The EATON AEROQUIP FC300 are AQP elastomer hoses with a blue, abrasion-resistant fabric cover with single wire braid reinforcement over a synthetic rubber inner tube for longer life. The FC300 hoses are designed for high pressure fluid applications such as power steering, hydraulics, air, fuel, lubricating oils, fire resistant hydraulic fluids and other industrial fluids. They are also suitable for biodiesel use up to B20 and max temperature of 212°F (100°C). Available in different internal diameters in inches and for use in different maximum operating pressures (psi). Priced and sold by the foot.

Indicative Applications:

Power steering lines

Hydraulics

Air

Gasoline

Fuel

Lubricating oils

Over the wall air tool

Dot-approved air brake

Max operating pressure is 2250 psi

Operating Temperature Range

-55°F to +302°F (-49°C to +150°C)

Air not to exceed +250°F [+121°C]

Notes: 

(1) The FC300 Hose only works with FC300 steel fittings (to be ordered separately). Easily assembles with a bench vise and/or wrenches.

(2) FC300-32 and FC300-40 hoses DO NOT meet SAE 100R5 pressure with reusable fittings. FC300-32 is rated to 350 psi with crimp fittings. 

Manufactured to the highest standards, the Andair standard fuel selector range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. Duplex fuel selectors are also offered by Andair (see separate product presentations). FS16, FS20 and FS25 series of fuel selectors are designed for safety, provide a precise and smooth feel in operation  and come in different types, ranging from Type 1 ON/OFF shut off valves to valves with multiple positions to ensure the right fuel tank selection. Can be supplied with different fittings. To prevent the pilot switching the wrong tank or turning the fuel off they feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off.

Designed for use with Light Sport and Ultralight aircraft, FS16 series 1/4" fuel selectors come in the following types:

Type 1 (FS16x1): simple 1/4” ON/OFF shut off valve with 90 degrees action between the two positions. On the FS16x1 there are two ports and either port can be used as the inlet or outlet.

Type 2 (FS16x2): Three way 1/4” fuel selector with positions LEFT-RIGHT-OFF and a 90 degree action between each tank selection. No lower fitting for use where there is little space behind the valve. 

Type 4 (FS16x4): Designed for high wing aircraft, it has four lever positions OFF - LEFT - BOTH – RIGHT with a 90 degree action between each position.On the FS16x4 there are 3 ports. The lower port is the outlet to the engine is 1/8 NPT Female. The inlet, side ports are 1/8 NPT Female and are at the 9 o'clock and 12 o'clock positions when looking at the valve with the brass ball spindle pointing upwards. At the 3 o'clock position there is a blanking plate that covers up a PTFE gland opposing the forces of the other 2 PTFE glands.

Type 2 and Type 4 valves do not allow cross feed between each tank when the selector is in the OFF position.

For additional information please refer to the product presentations, the supplied documentation or contact us.

ZF FRIEDRICHSHAFEN AG (also known as ZF Group) is a global technology company offering products and systems for vehicle motion control, integrated safety, automated driving, and electric mobility. The product portfolio is continuously enhanced and adapted to the market conditions and safety requirements. ZF products and systems ae extensively used in passenger cars, commercial vehicles as well as in various other sectors such as defense and aviation industries, construction and agricultural machinery, wind power, marine propulsion, rail drives and test systems. ZF Aftermarket is world's leading supplier in the automotive and industrial aftermarket, offering an exceptional product range of OE quality spare parts and services.

ZF has decades of experience in the design and development of marine propulsion systems. The company offers complete driveline systems as well as components for all types of vessels – motor yachts, watersports boats, high-speed ferries, workboats and commercial vessels, in a power range from 10 to 12,000 kW. The product portfolio includes a comprehensive range of transmissions (reversing, non-reversing and hybrid), propellers, steering systems and CAN-bus-compatible electronic control systems, azimuth thrusters, tunnel thrusters and sail drives. ZF spin-on transmission gearbox oil filters are used in different series of ZF Marine Propulsion Systems. With high quality, intelligent design concepts and individual service, ZF guarantees minimum downtimes and low life cycle costs. Customer range for these systems include shipyards, ship owners and operators as well as engine manufacturers worldwide. 

For additional information please consult the supplied documentation.

The RAPCO Dry Air Vacuum/Pressure pumps are are FAA approved quality and performance pumps intended for use as direct replacements of respective models of AIRBORNE and AERO ACCESSORIES (AA) in vacuum or pressure system applications. They are offered as NEW or OVERHAULED.

The NEW RAPCO Air Vacuum/Pressure pumps are FAA-PMA approved and have an inspection port for monitoring vane wear and determine when replacement is needed. An oil seal on the main shaft helps to prevent oil from entering and damaging the pump. Cooling fins reduce operating temperatures and help to extend pump life. They are internally coated with a special Mil-Spec. hard lube coating reducing friction and wear. The carbon rotor has also been improved by chamfering the leading edges of the vane slots reducing failure due to foreign object damage. With every pump, RAPCO includes a mounting gasket and vane measuring caliper. Fittings not included. There is no core charge when purchasing a new RAPCO dry air pump.  Manufacturers warranty on the 200 series is three years / 1300 hours. The warranty period on the 240 and the 400 series is 1 year / 500 hours, which ever comes first. There is no Core Charge on new pumps. 

The OVERHAULED RAPCO pumps are FAA approved and come with an FAA form 8130-3. Mounting gasket included. The warranty period for the 200 series is two years / 1000 hours. The warranty period for the 240 and the 400 series is one year / 400 hours, which ever comes first. Core charge applies. Please refer to the attached documentation for additional information.

The RAPCO Model RA215CC Dry Air Pump is used in ROTAX® 912 UL, 912 ULS and 914 UL engines. This pump replaces the old model 211CC and can also be used in other engines listed below:

Textron Lycoming: O-235, O-290, O-320, O-360, O-435, O-540, IO-320, IO-360, IO-540, IO-720, TIO-360, TIO-540, GO-480, GSO-480

Continental: O-300, GO-300, IO-360, TSIO-360, TSIO-520, GTSIO-520

The RAPCO Model RA215CC-9  replaces the old model 211CC-9. It is the most common model in General Aviation applications using the O-200 engine. This pump can be used with Continental C90-16F, all 0-200 engines and most Lycoming O-320 engines installed on Cessna 150s, 172s, etc.

The RAPCO Model RA216CW replaces the old models 212CW, 216CW and RAPCO P/N RA212CW. This pump can be used with a wide range of aircraft engines including Textron Lycoming LIO-360, GO-435, TIO-541 and Continental E-185, E-225, IO-346, O-470, IO-470, TSIO-470 and IO-520.

ATTWOOD SAHARA automatic bilge pumps are self-contained in one compact yet durable low profile bilge pumping package, including pump, wire seals, strainer and mercury-free switch. Their new SAHARA Mk2 pumps replacing older Mk1 models are the only automatic bilge pump that eliminate air-locks with their patented X-Air™ impeller ejecting trapped air in the pump and pipework. They are designed for ultimate reliability and durability in both freshwater and saltwater applications.

SAHARA Mk2 are the easiest automatic bilge pumps to install and service. They can be installed quickly and easily in tight spaces while servicing the pump cartridge from hard-to-reach areas is possible using only one hand. External mounting feet and integrated outlet reduces time and effort. Their universal mounting patterns makes them backwards compatible with the most popular bilge pumps on the market making their replacement simple.

SAHARA Mk2 pumps offer 40% better protection against water ingress and electrolysis vs. their Mk1 counterparts and 2 times better protection than the leading competition. ATTWOOD’s SteadySwitch™ reduces cycling and extends the life of the pump. They are covered with 3-Year Warranty.

SAHARA Mk2 automatic bilge pumps come in 3 models depending on their GPH capacity:

- S500 12V DC with a 500 GPH capacity at open flow, sized for boats up to approximately 17 feet,

- S800 offered in 12V/24V DC configurations with a 800 GPH capacity at open flow, suitable for larger recreational boats,

-  the most powerful and efficient S1200 pumps offered in 12V/24V DC configurations with a 1200 GPH capacity at open flow, suitable for larger boats and yachts.

Service kits for SAHARA Mk2 pumps are also offered.

For additional information please refer to the supplied documentation.

LENZ externally-mounted tank hydraulic suction line strainers are offered in different NPT and SAE series below to cover the needs of a range of applications.They do not require access to the tank interior for ease of servicing and feature perforated steel support tubes, cast iron bushings and 100 mesh stainless steel pleated screens as standard.

Part Numbers include subsections for the Series, the Size, the By-pass Option and the Mesh Oprion of the strainer.

Versions with by-pass options are designated by "-R" and PSI number after the size number of the strainer (e.g. -R3 and -R5 for 3 or 5 PSI by-pass options respectively).

Versions with mesh options, other than 100 mesh stainless steel pleated screen, are indicated by "-" and the number of the mesh option (i.e. -30, -60, -200  for 30, 60 or 200 mesh respectively).

LTF series are male NPT (MNPT) tank strainers designed for flows up to 50 GPM (200 LPM), with 2" X 2" MNPT steel nut. Offered with No by-pass or 5 PSI by-pass and 30, 60 and 200 mesh  options.

LTM series are male NPT (MNPT) to female NPT (FNPT) tank strainers designed for flows up to 200 GPM (750 LPM) with cast iron nut (stainless nut as option). Offered with No by-pass, 3 or 5 PSI by-pass and custom mesh  options.

LTMA series are male SAE (MSAE) to female SAE (FSAE) tank strainers designed for flows up to  40 GPM (160 LPM). They come with Buna o-rings and steel zinc plated bushings. Offered with No by-pass , 3 or 5 PSI by-pass and 30, 60 and 200 mesh  options.

LTMAB series are male SAE (MSAE) to hose barbed tube externally-mounted tank strainers designed for flows up to 40 GPM (160 LPM). They come with 1" to 2" hose beads, Buna o-rings and forged Zinc plated fittings.  Offered with No by-pass, 3 or 5 PSI by-pass and 30, 60 and 200 mesh  options.

For additional information please refer to the supplied documentation.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different oil filters and other oil system parts are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different air filters are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

Switches for different functions, inteneded for use in Piper aircraft. Information on their applicability to different Piper aircraft models and serial numbers is included. For additional information and/or non listed switches please contact us.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different vacuum pumps are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. The RAPCO FAA/PMA'd vacuum pump, RA215CC  is used in ROTAX® 912 UL, 912 ULS and 914 UL engines. Please refer to the separate product presentation for RAPCO Dry Air Pumps for vacuum or pressure system applications.

Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

LOWARA e-SV™ Series Stainless Steel Vertical Multistage Pumps

The LOWARA e-SV™ range  of vertical multistage pumps are highly reliable and technologically advanced multipurpose pumps and includes models in eleven sizes  with 1-3-5-10-15-22-33-46-66-92-125 m³/h nominal capacities.

All pumps ≥ 1.5kW are equipped with IE3 standard motors.

Design features:

Balanced mechanical seal replaceable with-out need for pump disassembling (for 10-15-22SV>=5,5kW, 33-46-66-92-125SV)

“O” Ring seat design to allow for simple outer sleeve dis-assembly

Floating for self alignment replaceable diffuser wear ring (PPS Glass filled technopolymer to withstand chemically corrosive, mechanically aggressive and high temperature liquids)

Reduced impeller axial thrust for longer standard motor bearing life (17,500h)

Hard Material Intermediate bush bearing (Tungsten Carbide/Silicon Carbide) to improve life and ability to withstand heavy duty applications, like boiler feeding

High temperature seal option (180°C max) with low NPSH design, high pressure design (up to 40 Bar), and passivated & electro-polished versions are available upon request.

0.37 - 18.5kw

Single or 3 phase

2 Year Warranty

Further unique features of the e-SV™ pumps include the integration of performance diagnostic devices such as the i-Alert™ vibration monitor and Dry Run sensor. The  i-Alert™ and the Dry Run sensor are available as an accessory for all models.

The e-SV™ pumps are certified by WRAS, ACS and D.M. 174 for use with potable water.

LOWARA e-SV™ Series Pump Versions:

e-SV: standard pump with IE3 motor

e-SVE: Variable speed Smart Pump with ultra premium efficiency IES2 drive package including a permanent magnet IE5 motor (up to 1,5 kW)

e-SVH: Variable speed pump with Hydrovar® pump controller (up to 22 kW)

For additional information please consult the Product Description section and the supplied documentation.

BRACKET Air Filters by BRACKET AERO FILTERS, Inc. have been in service on aircraft and helicopters for many years. BRACKET Foam Filters are installed as factory  original equipment (OEM) on 16 current production aircraft and four helicopters. They number 88 different FAA-PMA approved models and they are also approved for sea planes. Their specially treated polyurethane element assures near total protection from any foreign material entering the system. Their treated foam is highly efficient at filtering with a dual stage foam element increasing dust holding capacity. They have no pleats to store dirt, they repel water, they are fire retardant and abrasive resistant and exhibit a good air flow for proper fuel/air ratio. Designed for low-cost maintenance with increased engine life requiring replacement of only the low cost element. FAA approved these air filter assemblies can replace original air filter units. Air filter elements are also offered for replacements.

The expected shelf life of Brackett elements stored in their original packaging and out of direct sunlight is 4 years from date of manufacture listed on the front of element packaging.This allows the element to be installed on an aircraft at the end of its shelf life.

CHALLENGER AVIATION PRODUCTS, Inc. manufactures high quality oil-impregnated, surgical cotton gauze-based aircraft air filters under FAA/PMA certification using K & N filter media. K&N Performance Filters have been well known in the automotive world for years, unsurpassed in airflow and filtering capability they are now one of the most used filters on the road today. Made of a woven cotton fabric instead of paper, the K&N filter medium offers superior filtering without the restriction of airflow presented with paper or foam filters. Fabric allows 50% more air to pass than paper, and almost 60% more than foam. This translates into more horsepower and improved fuel economy.

Based on K&N technology CHALENGER filters have been certified for most general aviation aircraft. Their pleated cotton/wire mesh filters are far less prone to being clogged than synthetic media or paper, and tests done by Challenger (at approximately 240 CFM air flow) show K&N filters typically flow 6.03 CFM as compared to 4.95 for the average pleated paper element and 4.93 CFM for the oil-coated foam variety.

CHALLENGER air filters can be used as replacement parts to other OEM products but an STC (available by CHALLENGER) is required. Air filters come with an application chart, instructions, warranty card and a STC request form which needs to be  filled out for approval for the specific aircraft. The filters comes with a gasket, but do not include the grease which is sold separately, unless otherwise stated.

Product Features:

Can be washed & serviced up to 25 times

Increase horse power 2-4%

Fire Retardant

Save money & improve efficiency

FAA-PMA approved

Ecologically sound

Better take-off and climb-out performance

Faster airspeed and/or better fuel consumption

Accordion fold design provides up to 5 times filtering surface of non-pleated designs

Please refer to the attached documentation on the application of CHALLENGER filters in different aircraft/models.

Manufactured to the highest standards, the Andair standard fuel selector range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. Duplex fuel selectors are also offered  (see separate product presentations). FS16, FS20 and FS25 series of fuel selectors are designed for safety, provide a precise and smooth feel in operation  and come in different types, ranging from Type 1 ON/OFF shut off valves to valves with multiple positions. To prevent the pilot switching the wrong tank or turning the fuel off they feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off.

FS20 series 3/8" fuel selectors provide a choice of lower and side fittings, and all units can be operated with an extension and universal joints. They come in the following types:

Type 1 (FS20-1): simple 3/8” ON/OFF shut off valve with 90 degrees action between the two positions. There are two ports and either port can be used as the inlet or outlet.

Type 2 (FS20-2): Three way 3/8” fuel selector with positions LEFT-RIGHT-OFF and a 90 degree action between each tank selection. No lower fitting for use where there is little space behind the valve. 

Type 3 (FS20-3): three way selector with the positions LEFT - RIGHT - OFF. Generally used in low wing aircraft with a tank in each wing.

Type 4 (FS20-4): Designed for high wing aircraft, it has four lever positions OFF - LEFT - BOTH – RIGHT with a 90 degree action between each position.There are 3 ports. The lower port is the outlet to the engine and can be Male AN-6, Female 1/4NPT or a  360 degree Banjo adjustable fitting with a male AN-6 end.

Type 5 (FS20-5): 4 way Fuel Selector ( 3 tanks and OFF ) with positions LEFT - MAIN - RIGHT - OFF, each at 90 degree intervals.

Type 7 (FS20-7): Newest in the range 3 way fuel selector with positions LEFT - RIGHT - OFF. The inlets are at the 45 degree positions, to the LEFT and RIGHT, and the outlet is at the base of the valve. FS20-7 has been designed for centre consol mounting.

Type 8 (FS20-8): 5 way Fuel Selector ( 4 tanks and OFF ) with positions LEFT TIP - LEFT - RIGHT - RIGHT TIP - OFF, each at 72 degree intervals. 

For additional information please refer to the product presentations, the supplied documentation or contact us.

Modern reciprocating-engine aircraft (especially large and high-performance ones) use electrically operated auxiliary fuel  boost and transfer pumps  to keep fuel moving toward the aircraft engine or move fuel between tanks to balance aircraft weight. Centrifugal boost pumps,  electric motor driven,  are the most common type and  are used to supply,back up the engine-driven fuel pump or transfer fuel between tanks if the aircraft is so designed. They are  most frequently  submerged in the fuel tank or located just outside of the bottom of the tank with the inlet of the pump extending into the tank. Cartridge/canister or in-tank mounted pumps supply fuel to the aircraft engine while reverse flow through the pump is prevented by check valves. The cartridge/canister design allows removal of the pump cartridge without draining the fuel tank. If the pump is mounted outside the tank, a pump removal valve is typically installed so the pump can be removed without draining the fuel tank.

The RAPCO FAA-PMA approved pumps are offered as direct replacements of the respective pumps by OEMs  such as PARKER AIRBORNE or DUKES (please refer to their separate product presentations). The letters " RA" in the beginning of the RAPCO part number are used to denote the correlation of RAPCO part number to the OEM part number. They incorporate modern design, materials, and manufacturing processes to provide high quality and performance fuel pumps at competitive prices. 

These pumps can be furnished  as NEW or OVERHAUL EXCHANGE, namely new or overhauled pumps in exchange of existing customer owned units (cores). In all exchange cases,  the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders with us when our co-operating supplier verifies that the unit is in a reasonable serviceable condition. In the case of overhauled pumps, these are overhauled in accordance with FAA-approved process specification and come with a FAA Form 8130-3. All  RAPCO fuel pumps are thoroughly tested for guaranteed pump performance, with a worldwide distribution and a full warranty (same as OEM). For additional information please consult the supplied documentation (*) or contact us.

(*) The supplied documentation is to be used for reference only. When selecting a part for installation consult the appropriate aircraft maintenace manual, parts catalogue, or equipment list for approved data.   

FACET FILTRATION GROUP® is the global leading manufacturer of filtration products and systems with an extensive range of products including filter cartidges, housings, water treatment equipment and complete systems. Group products are covering a wide range of applications from aviation fueling and onshore, offshore or onboard marine applications to protection from debris and water contamination of diesel fuel supply of heavy equipment and water treatment facilities. FACET® fuel pumps and filters for aviation uses are separately presented.

The PARKER AIRBORNE designs and manufactures motor driven fuel fuel  boost and transfer pumps and is part of the PARKER AEROSPACE GROUP of the PARKER HANNIFIN CORPORATION. These pumps consist standard equipment by the world's leading airframe manufacturers. The PARKER AIRBORNE product range includes:

- In Line fuel pumps for low-flow fuel applications,

- Submerged Centrifugal fuel pumps,

- High Performance Centrifugal fuel pumps for use in turboprop or turbofan jet aircraft,

- Submerged Duplex fuel pumps with two distinct pumping elements

The PARKER AIRBORNE fuel boost pumps use 28 V direct current (DC) to drive a highly efficiency, brushless DC (BLDC) motor or 115.5 V alternating current (AC) three-phase induction motors. The BLDCmotor-driven pumps incorporate integral electronic controllers using Hall Effect sensor rotor-position feedback. The hardware-only controller doe not use any software or programmable logic devices. These pumps feature:

-fuel cooled motor and electronics

-fuel wetted carbon bearings allowing for long-life fluid film design with no rotating shaft seals

-a high efficiency brushless DC (BLDC) motor or a three-phase induction motor

-qualification for high levels of lighting and electromagnetic interference (EMI).

The PARKER AIRBORNE fuel boost pumps can be furnished as either NEW, NEW EXCHANGE or OVERHAUL EXCHANGE. 

Offered pumps in OVERHAUL Condition are supplied in accordance with FAA-approved process specification, come with a FAA Form 8130-3 and can be provided in exchange of existing customer owned units (cores). In all EXCHANGE cases,  the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders with us when our co-operating supplier verifies that the unit is in a reasonable condition. For additional information please consult the supplied documentation (*) or contact us.

In addition to the PARKER AIRBORNE pumps, RAPCO FAA-PMA approved pumps are also offered as direct replacements  to the respective PARKER AIRBORNE models. The RAPCO replacement pumps can be furnished as either NEW EXCHANGE or OVERHAUL EXCHANGE (please refer to their separate product presentation).

(*) The supplied documentation is to be used for reference only. When selecting a part for installation consult the appropriate aircraft maintenance manual, parts catalogue, or equipment list for approved data.

Made from 14L 12 steel and cadmium plated, SAF-AIR FAA-PMA approved push type fuel drain valves are close tolerance valves of simple design. These valves provide the most trouble free operation of any other line of valves in the industry. SAF-AIR valves are manufactured with an o-ring placed on the stem to seal against a flat seat on the body. This design eliminates an area where dirt can gather, thus putting an end to the main cause of fuel drain valve drip. Available in eight models in two styles with or without 1/4" hose adapter.

CURTIS PLT-275AV Flush Valves 6 Holes' Adapter Plates Assembly.

Product Specifications:

Diameter: 2.75 in.

Depth: 640,000-650,000

From Mounting Surface to Bottom Hole Diameter: 1-1/2 in.

Not Certified

TEMPEST®, a TEMPEST AΕΡΟ GROUP™ affiliate, offers their Platinum Electronic Fluid Pump line with a range of electronic fuel pumps designed to replace many of the FACET® GOLD-FLO solid state fuel pumps. FAA/PMA certified, TEMPEST® operate in 14 to 28 volt systems of modern aircraft and use an internal high-flow filter element that can be easily replaced when specified by aircraft maintenance manuals. Use of TEMPEST® Platinum Electronic Fluid Pumps in most Cessna aircraft requires installation of tank modification SK421-26C service kit separately priced.

The pump filter element must be changed when specified by the aircraft maintenance manual or when the pump output/pressure diminishes (an event that may indicate a dirty clogged filter). A universal Filter Kit  P/N KIT-P1 is offered which fits all Aero Accessories Platinum Pumps and includes filter P/N 79729, gasket P/N 79136 & O-ring P/N 79139-2.

For additional information please refer to the supplied documentation.