Since its introduction in 1994, the B&C SPECIALITY PRODUCTS BC320 Starter for Continental engines has established an impressive service record as the ONLY starter design on the market that has provided reliable, long-term service for these engines. 

Suitable for installation on Continental engines (C-75, C-85, C-90, C-145-2, O-200, IO-240, O-300-A, -B, and -C, and GO-300-A, -B, and -C) it solves all the problems that other starter designs have had:  worn-out clutches, broken pinions, nagging oil leaks, and catastrophic failure modes. Featuring the durability of all-steel gears and heavy-duty ball-bearings, and the efficiency of a high-torque series-wound motor, it provides greater starting torque, while saving 4.3 to 5.2 lbs. over the old key-type and pull-cable type starters (respectively).

The B&C SPECIALITY PRODUCTS BC320 Starter is STC-PMA approved for use in certificated aircraft, and is available with or without the STC (*). Two installation kits are also available:  one for replacing a key-type starter (Installation Kit 501-1), the other for replacing a pull-cable type starter (Installation Kit 501-3). For key-type starters, before installing the BC320, you will need to remove the needle bearing pressed into the engine case & install the supplied plug in its place. For pull-cable starters, before installing the BC320, you will need to cut off the 9/16 steel shaft that is installed in your engine case.

Other versions of BC320 Starter for 12v and 24v electrical systems (BC320-2, 12v Counter-Rotating or the 24v BC320-3) are also available.

(*) For the issue of the STC, the aircraft make and model, aircraft registration and serial number are required.

EXXONMOBIL® AVIATION Mobil Jet Oil 254 is a third-generation oil formulated to deliver exceptional high-temperature thermal stability  (HTS), excellent resistance to coking and deposit control as well as exceptional oxidation and corrosion protection. It meets the demanding requirements of latest technology  aircraft-type gas turbines operating over a wide range of severe operating conditions.  When compared to a typical Type II lubricant, Mobil Jet Oil 254 reduces bulk oil oxidation by up to 50 percent and shows deposit control capability 50 F higher.  These properties have been confirmed in various laboratory tests including; the Corrosion-Oxidation Stability Test,  Alcor Deposition Test, Vapor Phase Coker, Erdco High-Temperature Bearing Test, Ryder Gear and the Mobil Thin Film Oxidation Test.The closely controlled low-temperature viscosity of Mobil Jet Oil 254, along with its low pour point (below -54 ºC), ensure good low-temperature fluidity to permit starting and lubrication at temperatures as low as -40 ºC.  In extensive laboratory testing and in-flight experience, Mobil Jet Oil 254 also exhibits excellent bulk oil stability at temperatures up to 232 ºC (450 ºF) for extended periods.  The evaporation rate at these temperatures is low enough to prevent excessive loss of volume.  The load-carrying ability of Mobil Jet Oil 254 comes from its synthetic base stock viscosity and, therefore, is not subject to loss from viscosity index additive shear.  

Product Features & Benefits:

Excellent thermal and oxidation stability reducing the formation of carbon (carbon coking) and sludge deposits. Helps operators reduce shop visits and maintenance costs. Maintains engine efficiency and extends engine life. Reduces bulk oil oxidation by 50% and increases deposit control by 50 ºF

Excellent wear and corrosion protection extending seal, gear and bearing life. Reduces engine maintenance. 

Viscosity and shear stability across wide temperature range providing effective lubrication at high operating temperatures

Chemically stable at high operating temperatures reducing evaporation losses and lowering oil consumption

Excellent resistance to foaming maintaining film strength under rigorous operating conditions

Good low temperature fluidity permiting start-up and ensuring effective lubrication of critical components at temperatures as low as -40 °F.

TOTALENERGIES (formerly TOTAL) Specialties has developed a comprehensive turbine lubricant product range to support the power generation industry (whether it’s for large frame or aero-derivative turbines) with approvals by the leading turbine manufacturers. Offered in 20-liter containers and drums of 208 liters (210 kg) each.

TOTALENERGIES PRESLIA range of turbine oils include: 

a) PRESLIA mineral high-performance turbine lubricants for regulation and lubrication circuits of gas, steam and combined cycle turbines working at high temperatures. Can also be used in centrifugal and screw compressor bearing lubrication when an oil without strong anti-wear properties is needed. These oils offer long drain intervals, simplified maintenance and  ageing protection of engines and equipment in which they are used. 

b) PRESLIA GT (ISO 32 and 46) high-running temperature resistant turbine lubricants. These oils are specially designed for the lubrication (bearing, gear boxes) and regulation of gas turbines. The use of non-conventional base stocks and unique additization provides excellent thermal-oxidative stability. Preslia GT 32 and 46 should also be considered for use in steam turbine applications that requires either an ISO 32 or 46 fluid.

c) PRESLIA SE synthetic lubricants for aero-derivative turbines. Formulated with an advanced polyolester-basestock and next generation additive technology, Preslia SE Jet (5cSt POE) provides outstanding performance in the most demanding land-based aero-derivative engine applications that require a SAE AS5780 qualified fluid. PRESLIA SE HTS (High Thermal Stability) is a High Temperature/Performance oil delivering the performance expected for aeroderivative gas turbines operating in the most difficult environments.

For additional information please consult the Product Description section and the supplied documentation.

Miscellaneous OEM special tooling / equipment used for the maintenance & repair of aircraft piston and turbine engines. Used by airline companies  and Aircraft Maintenance, Repair and Overhaul facilities (MROs) in various applications. Available in NEW or USED conditions.  For additional information please consult the supplied documentation or contact us for non listed tools.

HONEYWELL AEROSPACE seals are engine parts widely used in aerospace applications. They are also available as FAA-PMA parts from other manufacturers. Supply of the specific parts can be effected either as OEM part numbers or any of respective FAA-PMA  part numbers subject to their availability by our suppliers.

P/N: 2-300-778-01 Fuel Manifold Gasket Seal is used in combustor turbine modules. It is also available as FAA-PMA part with alternative P/N: DEC2-300-778-01 by HEICO AEROSPACE and P/N: NK1004054-10 by EATON CORPORATION. 

An oil pressure sensor is a device used to measure the oil pressure on an engine. The term oil pressure sensor is often used to denote  at least two different and distinct types of sensor - an oil pressure switch and and oil pressure sender.

An oil pressure switch is an egine protection device. It is a mechanical device that has a switch inside. The oil pressure switch may be 1, 2, or 3 insulated terminals (pins). Traditionally most oil switches for protection close when they activate, to show low oil pressure. 

An oil pressure sender is a device that senses the oil pressure of an engine and transmits it to the engine or machine controller. It is used as a generator protection device, to display the oil pressure to a user or for logging and diagnostic purposes. Unlike an oil pressure switch, it can display a range of readings.

Oil pressure sensors are used aircrafts and offered either as parts from the respective OEMs or as replacement parts from third parties. They are alternatively termed as HOBBS switches.

Please refer to the manufacturer Illustrated Part Cataloge (IPC) or the technical specifications of offered sensiors to select the right sensor for your application.

AEROSHELL® Turbine Oil 308 is a 3 mm2/s synthetic ester oil incorporating additives to improve resistance to oxidation and corrosion and to minimise wear. It was developed specifically for use in particular models of aircraft turbo-prop and turbo-jet engines for which a MIL-PRF- 7808 (formerly MIL-L-7808) oil is required. AEROSHELL® 308 turbine oil contains a synthetic ester oil and should not be used in contact with incompatible seal materials and it also affects some paints and plastics.

Product Specifications/Approvals:

US – Approved MIL-PRF-7808L Grade 3

Nato Code O-148

Joint Service Designation – Equivalent OX-9

Airbus Helicopters CM  CM0113

NOTE: Other AEROSHELL® piston engine and turbine oils, greases and fluids are also offered through our Web Platform for Supplies or can be furnished through our network of co-operating suppliers. Due to our continuously expanding list of suppliers and their respective range of offered products, certain AEROSHELL® products may not be currently listed in our Platform. Please refer to the supplied list of offered products or contact us for additional information or assistance on non listed products.

AEROSHELL® Turbine Oil 560 is a third-generation 5-centistoke synthetic hindered ester lubricating oil, which offers reduced coking, improved wear resistance, and all-round commercially viable performance for modern jet engines. It meets or exceeds the most exacting requirements of turbine oil technology standards as outlined in SAE AS 5780A. For more information please refer to the attached documentation.

Product Features:

Reduced coke formation: Coke formation and shedding can be disruptive to airline operations. Reduced coke deposits can lower maintenance costs and increase on-wing life.

Fully compatible with other approved oils: No engine problems such as coke shedding and oil filters blocking is experienced when changing from one approved oil to AeroShell Turbine Engine Oil 560, in accordance with the engine manufacturer recommendations.

No adverse effect on elastomer seals: AEROSHELL® 560 has good elastomer compatibility which reduces the possibility of oil leaks that could lead to expensive engine overhauls or even an in-flight engine shutdown.

Good oxidative and thermal stability:The use of AEROSHELL® 560 reduces the occurrence of oxidative and thermal degradation of the oil at high operating temperatures, which could result in high overhaul and maintenance costs due to:

1. An increase in oil viscosity, which may result in the need for oil change;

2. An increase in acidity, which could lead to the corrosion of gears and bearings; and

3. Sludge formation in the oil system, causing the blockage of oil jets and filters.

AEROSHELL® Turbine Oil 560  Approvals:

US – Approved MIL-PRF-23699G Grade HTS, Approved SAE AS5780B Grade SPC

British – Equivalent DEFSTAN 91-101

French – Equivalent DCSEA 299/A

Russian – Analogue to VNII NP 50-1-4F, B3V, LZ-240, VNII NP 50-1-4U, and 36/Ku-A

NATO Code – O-154

Joint Service Designation – Equivalent OX-27

NOTE: Other AEROSHELL® piston engine and turbine oils, greases and fluids are also offered through our Web Platform for Supplies or can be furnished through our network of co-operating suppliers. Due to our continuously expanding list of suppliers and their respective range of offered products, certain AEROSHELL® products may not be currently listed in our Platform. Please refer to the supplied list of offered products or contact us for additional information or assistance on non listed products.

AEROSHELL®Turbine Oil 750 is a 7½ mm2 /s synthetic mixed ester oil containing a thickener and additives which provide excellent load carrying, thermal and oxidation stability. It meets the requirements of DERD 2487 (now DEF STAN 91-98) and was developed to provide a high standard of lubrication specifically for British and Russian turbo-prop engines, especially those calling for mineral turbine oils and particularly turbo-prop engines where a good load carrying oil was required for the propeller reduction gearbox. Approved by the Russian authorities as an analogue to MN-7.5u and for those Russian turbo-prop applications which require the use of mixtures of mineral turbine oil and aircraft piston engine oil. 

AEROSHELL® Turbine Oil 750 contains a synthetic ester oil and should not be used in contact with incompatible seal materials and some paints and plastics as this oil may negatively impact their function. Available in US Quarts and Drums of 55 US Gallons. 

Specifications:

British: Approved DEF STAN-91-98 (replaces DERD 2487)

French: Equivalent to AIR 35174A

Joint Service Designation: OX-38

NATO: O-149 (equivalent O-159)

Russian: Analogue to TU 38.1011722-85 Grade MN-7.5u

Approvals:

Honeywell: Auxiliary Power Units (some models)

Pratt & Whitney Canada: PT6 (some models)

Rolls-Royce: Dart, Tyne, Avon (some early models only), Gnome, Pegasus, Palouste, Nimbus, Proteus, Orpheus, Olympus 200 and 300

Sikorsky: S-61N transmissions

Soloviev: D30 engine

Turbomeca: Astazou, Bastan, Turmo, Artouste, Arriel, Malika

For more information please refer to the attached documentation.

NOTE: Other AEROSHELL® piston engine and turbine oils, greases and fluids are also offered through our Web Platform for Supplies or can be furnished through our network of co-operating suppliers. Due to our continuously expanding list of suppliers and their respective range of offered products, certain AEROSHELL® products may not be currently listed in our Platform. Please refer to the supplied list of offered products or contact us for additional information or assistance on non listed products.

AEROSHELL® 500 2nd Generation Synthetic Turbine Engine Oil from Shell Aviation is a 5 centistoke synthetic hindered ester oil incorporating additives to improve thermal and oxidational stability and also metal passivation. Developed essentially to meet the requirements of Pratt & Whitney 521 B Type II and MIL -L-23699 specifications, it is suitable for certain civil and military aero-engines requiring this class of lubricant but also approved for use in their industrial and marine derivatives which retain the essential design elements of their aviation versions. High Viscosity Index Synthetic Base Fluids used in AEROSHELL® Turbine Oil 500 maintain viscosity and protect components more effectively under the high shear stresses that a turbine system places on lubricants. The outstanding high temperature and oxidation stability of AEROSHELL® Turbine Oil 500 is due to the natural properties of the synthetic hindered ester base fluids used. These fluids are clean running in that they tend to dissolve varnish and sludge rather than leave deposits on working surfaces.

Available in US Quarts, 20 Lt Pails and Drums of 55 US Gallons. Meets U.S. Approved MIL-PRF-23699G Grade STD specification. 

Product Features:

Outstanding high temperature and oxidation stability.

High Viscosity Index Synthetic Base Fluids maintain viscosity and protect components.

Qualified to MIL-L-23699, DERD 2499 and NATO O-156 fluid [ A qualified product must be blended and packed in the plant listed on the QPL to ensure that the base oil is made in an approved refinery and that the product is blended and packed in an approved and closely monitored facility.] which provides compatibility with other similarly qualified oils.

Excellent load carrying properties.

Good low volatility characteristics.

For more information please refer to the attached documentation.

NOTE: Other AEROSHELL® piston engine and turbine oils, greases and fluids are also offered through our Web Platform for Supplies or can be furnished through our network of co-operating suppliers. Due to our continuously expanding list of suppliers and their respective range of offered products, certain AEROSHELL® products may not be currently listed in our Platform. Please refer to the supplied list of offered products or contact us for additional information or assistance on non listed products.

The PARKER AIRBORNE designs and manufactures motor driven fuel fuel  boost and transfer pumps and is part of the PARKER AEROSPACE GROUP of the PARKER HANNIFIN CORPORATION. These pumps consist standard equipment by the world's leading airframe manufacturers. The PARKER AIRBORNE product range includes:

- In Line fuel pumps for low-flow fuel applications,

- Submerged Centrifugal fuel pumps,

- High Performance Centrifugal fuel pumps for use in turboprop or turbofan jet aircraft,

- Submerged Duplex fuel pumps with two distinct pumping elements

The PARKER AIRBORNE fuel boost pumps use 28 V direct current (DC) to drive a highly efficiency, brushless DC (BLDC) motor or 115.5 V alternating current (AC) three-phase induction motors. The BLDCmotor-driven pumps incorporate integral electronic controllers using Hall Effect sensor rotor-position feedback. The hardware-only controller doe not use any software or programmable logic devices. These pumps feature:

-fuel cooled motor and electronics

-fuel wetted carbon bearings allowing for long-life fluid film design with no rotating shaft seals

-a high efficiency brushless DC (BLDC) motor or a three-phase induction motor

-qualification for high levels of lighting and electromagnetic interference (EMI).

The PARKER AIRBORNE fuel boost pumps can be furnished as either NEW, NEW EXCHANGE or OVERHAUL EXCHANGE. 

Offered pumps in OVERHAUL Condition are supplied in accordance with FAA-approved process specification, come with a FAA Form 8130-3 and can be provided in exchange of existing customer owned units (cores). In all EXCHANGE cases,  the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders with us when our co-operating supplier verifies that the unit is in a reasonable condition. For additional information please consult the supplied documentation (*) or contact us.

In addition to the PARKER AIRBORNE pumps, RAPCO FAA-PMA approved pumps are also offered as direct replacements  to the respective PARKER AIRBORNE models. The RAPCO replacement pumps can be furnished as either NEW EXCHANGE or OVERHAUL EXCHANGE (please refer to their separate product presentation).

(*) The supplied documentation is to be used for reference only. When selecting a part for installation consult the appropriate aircraft maintenance manual, parts catalogue, or equipment list for approved data.

AIRBUS HELICOPTERS is one of the three divisions of EUROPEAN AERONAUTIC DEFENCE AND SPACE CO (EADS), a European aerospace corporation which designs, manufactures and sells civil and military aerospace products worldwide. The other two divisions are  Commercial Aircraft and Defence and Space. AIRBUS civil helicopters, grouped in families range from single- and twin-engine light and medium rotorcraft, up to those in the eleven-ton-class and aim to handle any and all civil missions. Civil range of AIRBUS HELICOPTERS includes:

H125 and H130 intermediate single engine helicopters,

H135 and H145 light twin engine helicopters,

H155 and H160 medium twin engine helicopters,

Eurocopter AS365 Dauphin (formerly known as Aérospatiale SA365 Dauphin 2) medium-weight multipurpose twin engine helicopter,

H175 super medium twin engine helicopter,

H215 and H225 heavy twin engine helicopters

Components and parts for the above helicopters are offered on demand as OEM or PMA parts in NEW or USED condition. These include among others rotables, blades, hardware, structural and engine parts.

PMA parts are generally listed in separate product presentations of their respective manufacturers. 

Please contact us for additional information.

ATS 7500 Aviation Piston Ring Compressor features a quick-change design to speed up piston ring installation. It includes HASTINGS Ring-O-Matic® pliers and bands that operate in all positions: not just vertically or horizontally. The pliers incorporates a precision locking action for exact holding and release of piston ring bands. The complete kit includes the Ring-O-Matic® pliers and one of each of the following size bands: 4-1/8" to 4-1/2", 4-1/2" to 4-3/4", 4-3/4" to 5", 5" to 5-1/4", and 5-1/4" to 5-1/2", 5-1/2" to 5-3/4". Shipping weight: 3 lbs (1.5Kg).

The new 3882 series Cylinder Base Nut wrenches by AIRCRAFT TOOL SUPPLY COMPANY (ATS) are made from forged alloy steel, tempered, and hardened for maximum strength. They also have an industrial chrome plating to improve surface wear, and protect against rust and corrosion. Their thin-wall construction guarantees they will fit nuts close to the cylinder casing without grinding down the wrench's outer diameter. And with a 15" span, they clear even the tallest cylinders. The new 3882 cylinder base wrenches replacing ATS 2882 series address just about every concern of the previous 2882 series, while including several enhancements for work easier while carrying the ATS Pro lifetime warranty. The set includes 4 wrenches in Hex Sizes: 1/2", 9/16", 5/8", and 3/4" suitable for all Continental, most Lycoming, and many other types of aircraft engines.

ALCOR, an affiliated company of TEMPEST AERO GROUP is a manufacturer of sensors, instruments, test equipment, fuel treatment products, parts and accessories.

ALCOR CHT FAA/PMA approved thermocouples are offered in Type J gasket, Type J bayonet and Type K bayonet styles.

AMT NETHERLANDS  designs and manufactures high performance gas turbine engines in different series with different specifications, start system options and delivered thrust ratings.  AMT LYNX Gas Turbines are only manufactured in E-start cofiguration with an direct kerosene starting system. They are offered in EPV layout and include the Engine Data Terminal. They deliver 1.569 N at 46.000 RPM. For additional information, please refer to the supplied documentation or contact us. 

AMT NETHERLANDS  designs and manufactures high performance gas turbine engines in different series with different specifications, start system options and delivered thrust ratings.  AMT NIKE Gas Turbines are only manufactured in E-start cofiguration with an direct kerosene starting system. They are offered in EPV layout and include the Engine Data Terminal. For additional information, please refer to the supplied documentation or contact us. 

AMT NETHERLANDS  designs and manufactures high performance gas turbine engines in different series with different specifications, start system options and delivered thrust ratings.  AMT TITAN Series gas turbine engines deliver 392 N at 96.000 RPM. They are offered in E-start or AIR start (10-12 Bar) configuration, with propane start or kerosene start system and with or without the Engine Data Terminal (EDT). For additional information, please refer to the supplied documentation or contact us. 

AMT NETHERLANDS  designs and manufactures high performance gas turbine engines in different series with different specifications, start system options and delivered thrust ratings.  AMT Olympus Series HP gas turbine engines deliver 230 N at 108.500 RPM. They are offered in E-start or AIR start (10-12 Bar) configuration, with propane start or kerosene start system and with or without the Engine Data Terminal (EDT). A spinoff of the Olympus HP is being certified by EASA for the use as a "bringing home device" for a full size glider. For additional information, please refer to the supplied documentation or contact us. 

AMT NETHERLANDS  designs and manufactures high performance gas turbine engines in different series with different specifications, start system options and delivered thrust ratings.  AMT Pegasus Series HP gas turbine engines deliver 167 N at 119.500 RPM. They are offered in E-start or AIR start (10-12 Bar) configuration, with propane start or kerosene start system. For additional information, please refer to the supplied documentation or contact us. 

Manufactured to the highest standards, the Andair standard fuel selector range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. Duplex fuel selectors are also offered  (see separate product presentations). FS16, FS20 and FS25 series of fuel selectors are designed for safety, provide a precise and smooth feel in operation  and come in different types, ranging from Type 1 ON/OFF shut off valves to valves with multiple positions. To prevent the pilot switching the wrong tank or turning the fuel off they feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off.

FS25 series 1/2" fuel selectors has been designed for engines up to 560 HP (50+ GHP), provides a choice of fittings and all units can be operated with an extension and universal joints. They come in the following types:

Type 1 (FS25-1): ON / OFF Shut Off valve for 1/2" fuel lines. There is a 90 degree action between the two positions and included with the valve is the safety button. 

Type 2 (FS25-2): Three way 3/8” fuel selector with positions LEFT-RIGHT-OFF and a 90 degree action between each tank selection. No lower fitting for use where there is little space behind the valve. 

Type 3 (FS25-3): Three way selector with positions LEFT - RIGHT - OFF. No lower fitting. This valve has inlets ports at the Left and Right hand side and the outlet towards the front.

Type 4 (FS25-4): Designed for high wing aircraft, it has four lever positions OFF - LEFT - BOTH – RIGHT with a 90 degree action between each position.There are 3 ports. The lower port is the outlet to the engine and can be Male AN-8, Female 3/8 NPT or a  360 degree Banjo adjustable fitting with a male AN-8 end.

Type 5 (FS25-5): 4 way Fuel Selector ( 3 tanks and OFF ) with positions LEFT - MAIN - RIGHT - OFF, each at 90 degree intervals. The inlet ports are around the side of the valve and the outlet is at the bottom of the valve.

For additional information please refer to the product presentations, the supplied documentation or contact us.

Manufactured to the highest standards, the Andair standard fuel selector range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. Duplex fuel selectors are also offered  (see separate product presentations). FS16, FS20 and FS25 series of fuel selectors are designed for safety, provide a precise and smooth feel in operation  and come in different types, ranging from Type 1 ON/OFF shut off valves to valves with multiple positions. To prevent the pilot switching the wrong tank or turning the fuel off they feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off.

FS20 series 3/8" fuel selectors provide a choice of lower and side fittings, and all units can be operated with an extension and universal joints. They come in the following types:

Type 1 (FS20-1): simple 3/8” ON/OFF shut off valve with 90 degrees action between the two positions. There are two ports and either port can be used as the inlet or outlet.

Type 2 (FS20-2): Three way 3/8” fuel selector with positions LEFT-RIGHT-OFF and a 90 degree action between each tank selection. No lower fitting for use where there is little space behind the valve. 

Type 3 (FS20-3): three way selector with the positions LEFT - RIGHT - OFF. Generally used in low wing aircraft with a tank in each wing.

Type 4 (FS20-4): Designed for high wing aircraft, it has four lever positions OFF - LEFT - BOTH – RIGHT with a 90 degree action between each position.There are 3 ports. The lower port is the outlet to the engine and can be Male AN-6, Female 1/4NPT or a  360 degree Banjo adjustable fitting with a male AN-6 end.

Type 5 (FS20-5): 4 way Fuel Selector ( 3 tanks and OFF ) with positions LEFT - MAIN - RIGHT - OFF, each at 90 degree intervals.

Type 7 (FS20-7): Newest in the range 3 way fuel selector with positions LEFT - RIGHT - OFF. The inlets are at the 45 degree positions, to the LEFT and RIGHT, and the outlet is at the base of the valve. FS20-7 has been designed for centre consol mounting.

Type 8 (FS20-8): 5 way Fuel Selector ( 4 tanks and OFF ) with positions LEFT TIP - LEFT - RIGHT - RIGHT TIP - OFF, each at 72 degree intervals. 

For additional information please refer to the product presentations, the supplied documentation or contact us.

Manufactured to the highest standards, the Andair standard fuel selector range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. Duplex fuel selectors are also offered by Andair (see separate product presentations). FS16, FS20 and FS25 series of fuel selectors are designed for safety, provide a precise and smooth feel in operation  and come in different types, ranging from Type 1 ON/OFF shut off valves to valves with multiple positions to ensure the right fuel tank selection. Can be supplied with different fittings. To prevent the pilot switching the wrong tank or turning the fuel off they feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off.

Designed for use with Light Sport and Ultralight aircraft, FS16 series 1/4" fuel selectors come in the following types:

Type 1 (FS16x1): simple 1/4” ON/OFF shut off valve with 90 degrees action between the two positions. On the FS16x1 there are two ports and either port can be used as the inlet or outlet.

Type 2 (FS16x2): Three way 1/4” fuel selector with positions LEFT-RIGHT-OFF and a 90 degree action between each tank selection. No lower fitting for use where there is little space behind the valve. 

Type 4 (FS16x4): Designed for high wing aircraft, it has four lever positions OFF - LEFT - BOTH – RIGHT with a 90 degree action between each position.On the FS16x4 there are 3 ports. The lower port is the outlet to the engine is 1/8 NPT Female. The inlet, side ports are 1/8 NPT Female and are at the 9 o'clock and 12 o'clock positions when looking at the valve with the brass ball spindle pointing upwards. At the 3 o'clock position there is a blanking plate that covers up a PTFE gland opposing the forces of the other 2 PTFE glands.

Type 2 and Type 4 valves do not allow cross feed between each tank when the selector is in the OFF position.

For additional information please refer to the product presentations, the supplied documentation or contact us.

The Andair standard fuel selector valve range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. 

Manufactured to the highest standards, all Andair fuel selector valves are designed for safety, provide a precise and smooth feel in operation and can be supplied with custom engraving. They feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off. All these features help prevent the pilot switching the wrong tank or turning the fuel off.

Andair duplex fuel selector valves have two separate compartments so that two independent fuel lines can be switched simultaneously making them ideal for fuel injected or diesel engines where there needs to be a return line. It allows to pipe surplus fuel to the same tank from which it was drawn. This avoids overfilling the return tank or having an overly complicated fuel system. 

FS2020(*) fuel selector valves feature two 3/8" sections for feed & return. FS2520(*) fuel selector valves feature one 1/2" feed section and one 3/8" return section. Both can be supplied with different ANDAIR fittings to meet application requirements. 

Engines that can benefit from these valves are Surburu, Continental, Rotax, and Diesel aircraft engines. 

For additional information please refer to the product presentations, the supplied documentation or contact us.

(*) Fittings in product titles relate to inlet from right tank, outlet to engine and inlet from left tank in the lower and upper side of the valve.

ARKWIN INDUSTRIES has been designing and manufacturing engine actuators for over 60 years for operation with fuel, engine oil and hydraulic oil pressurization. Their actuators are used on numerous civil, military, and industrial applications to provide actuation force to direct engine control components. They differ from conventional hydraulic actuators, a major difference being the incorporation of the fire resistance features necessary to meet engine safety requirements. Engine actuators are frequently exposed to elevated temperature during normal operation. If extended periods of flame resistance are required, protective coatings can be applied to the actuator housings including the use of intumescence or ablative coatings. Where temperature permits, ARKWIN uses aluminum alloys. For higher operating  temperatures or pressure requirements exceeding the allowables of aluminum alloy, stainless PH steel alloys or titanium alloys can be provided. Two stage sealing is common for both static and dynamic seals. Specifically selected seal compounds allow zero external leakage, long durability life, high temperature resistance, while providing protection in fire. 

ARKWIN’s  engine actuators feature a high side load tolerance to ensure long piston life, high resistant wear plating, high reliability/low maintenance and fire resistance. Their key design characteristics include:

• Fuel and petroleum based operating fluids

• Operating pressures up to 4,000 psig

• Position feedback of the actuators is provided by integral or externally mounted LVDT’s.

• Multiple mounting options

• Servo valve applications (Control of actuators through external pressurization valving or through an integral electro hydraulic servo valve).

• Master/Slave configurations

ARKWIN’s  engine actuators are offered for different platforms including:

CFM International CFM56-2/-3, CFM56-5/-7

General Electric CF34-3, CF34-8C/E, CF6, F110, F404,  F414, LM2500, LM6000, TF34

ARKWIN EXCHANGE PROGRAM: ARKWIN’s commercial and industrial gas turbine engine actuator exchange program was developed for the CFM56-5/7, CF6-80C2, CF6-80E1, CF34-8C/E, LM2500, and LM6000 engines.  The program provides operators the reliability of OEM NEW products at competitive prices. Qualifying actuators are exchanged in a very short time for FACTORY NEW OEM production units complete with FACTORY NEW OEM and a three-year/6000 EOH warranty. For additional information please consult the supplied documentation or contact us.

The AVIASPORT indicators (gauges) are reliable, accurate and solid, combining the accumulated experience of more than twenty years with the latest technology  They have been designed for ROTAX engines and their display areas are divided into red, green and yellow zones in line with Rotax limits. They use a pointer that turns 240º or 320º, providing high resolution. AVIASPORT range of gauges includes CHT, EGT, tachometers, oil and fuel pressure, oil and coolant temperature, fuel level, voltmeters & ammeters and offered with casings of different sizes: 80mm; 57mm and 52mm.

The AVIASPORT fuel pressure gauges  have been designed especially to measure fuel pressure in Rotax® engines 912 and work both with 12V and 24V systems. Unlike mechanical gauges, the AVIASPORT ielectronic gauges use a high precision sensor to be installed close to the engine, preventing fuel lines in the cockpit. These gauges are sold without sending units or as kits with matching senders whenever specified.

The AVIASPORT indicators (gauges) are reliable, accurate and solid, combining the accumulated experience of more than twenty years with the latest technology  They have been designed for ROTAX engines and their display areas are divided into red, green and yellow zones in line with Rotax limits. They use a pointer that turns 240º or 320º, providing high resolution. AVIASPORT range of gauges includes CHT, EGT, tachometers, oil and fuel pressure, oil and coolant temperature, fuel level, voltmeters & ammeters and offered with casings of different sizes: 80mm; 57mm and 52mm.

AVIASPORT Oil Pressure indicators (gauges) are designed specifically for ROTAX 912/914 aircraft engines with painted red, green, and yellow gauge markings. are available in two sizes: 52 and 57 mm. They are offered in two unit versions for readings in PSI or Bars. They work with different pressure sensors depending on these installed in ROTAX 912/914 engines: the VDO sensor (Before September 2008) or the 4..20mA sensor (after 2008).

Turbine engine oils (abbreviated as TEOs), also known as jet oils, turbo oils are specialty lubricants designed to support the operation of turbine engines. Apart from their lubricating function of the engine,  gearbox, shafts and associated accessories, TEOs have two additional functions. Their various additives protect the components from corrosion, and filter contaminants in the engine such as carbon deposits (coking) while TEOs are also used as heat transfer fluids, cooling the engine in temperatures reaching 1000°C, in turn extending the life of the oil up to 25,000 hours of operation. TEOs have been initially developed as mineral and and subsequently innovated to synthetic.

Castrol™ 5000 is a 5 centistoke "Type II" synthetic lubricant designed for use in modern gas turbine engines operating at bulk oil temperatures exceeding those which "Type I" oils can successfully withstand. It  is a clear, amber-colored fluid having the appearance of a thin oil with a faint aromatic odor. It is based on a blend of high quality hindered esters and additives used to offer a product with excellent high temperature and oxidation stability, good load-carrying properties and complete compatibility with engine and accessory constructional materials, such as metals and elastomeric sealing compounds. 

Castrol™ 5000  is compatible with other MIL-PRF-23699F Std, 5 centistoke gas turbine lubricanrts such as AEROSHELL® 500, 560, EXXONMOBIL® Mobil Jet Oil II, EXXONMOBIL® Mobil Jet Oil 254, EASTMAN Turbo Oil 2380™ and others. However, it is unwise to mix grades of different viscosity.

Castrol™ 5000  oil  is not compatible with mineral oils and while it is miscible with phosphate ester hydraulic fluids, the latter will have a detrimental effect such as coking propensity and resistance to corrosion. 

For additional information and specifications please refer to the supplied documentation.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft. They form part of  BRP-Powertrain GmbH & Co. KG product portfolio which also includes engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles & carts.

The BRP-ROTAX® 916 iS series are turbo charged four cylinder aircraft engines with best power-to-weight ratio and TBO 2,000h. This series includes non-certified (916 iSA)  and EASA CS-E certified models (916 iScA) and also models for 24V power aircraft supply systems (non-certified 916 iSA C24 and EASA CS-E certified 916 iScA C24).

916 iS Series Engine Features:

Four-stroke piston engine with four liquid and air-cooled cylinders

Redundant electronic fuel injection and ignition, eco mode

Turbocharger, stainless steel exhaust

Dry sump forced lubrication with separate oil tank, automatic adjustment by hydraulic valve tappets

Engine management system (EMS)

Electric starter (12 or 24 Volt)

Propeller speed reduction gearbox

Intercooler

TBO 2,000 hrs

Maximum operating altitude 23,000 feet

Full take-off power up to 15,000 feet

Available Options (supplied with the engine):

air guide baffle installed

2 electrical fuel pumps

silicon water hoses

NOTE: Options are additionally charged and must be specified at the time of ordering. They can only be ordered with the respective engine(s).

For additional information please refer to the supplied documentation.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different sensors are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer depending on the type of the engine. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different wire harnesses are parts intended for use in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Ignition systems and parts are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from BRP-ROTAX® but also from other manufacturers.  Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different vacuum pumps are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. The RAPCO FAA/PMA'd vacuum pump, RA215CC  is used in ROTAX® 912 UL, 912 ULS and 914 UL engines. Please refer to the separate product presentation for RAPCO Dry Air Pumps for vacuum or pressure system applications.

Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different air filters are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different springs are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Airboxes are used in ROTAX® aircraft engines to remove SOME of the difficulties created by having two independent induction systems. They simplify sourcing the air for both carburetors. Depending on the installation, the air temperature and/or pressure within the engine cowling may be significantly different on each side. Airboxes make it easy to run a single intake hose to a point on the aircraft where preferred ambient air can be obtained. They also make the provision of the same carb heat air simpler to each carburetor.

BRP-ROTAX® airboxes and parts are offered as certified or non certified from BRP-ROTAX®.  Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Exhaust systems and parts are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from BRP-ROTAX® but also from other manufacturers.  Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Shock mounts and mount sets are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from BRP-ROTAX® but also from other manufacturers.  Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Revolution Counters (Tachometers)/HOBBS meters are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from BRP-ROTAX® but also from other manufacturers.  Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Fuel pressure gauges are used in BRP-ROTAX® aircraft engines and offered as certified or non certified parts from their respective manufacturers. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation.

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

Fuel pressure gauges are no longer offered as ROTAX Part Numbers. These part numbers are provided for reference only. For these gauges please refer to our product presentation on AVIASPORT Fuel Pressure Gauges or contact us.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different spacers are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different alternators are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different starter relay assemblies are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different cylinder heads and cylinder head assemblies are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different screws, such as hexagonal, allen, fixation and others are used in BRP-ROTAX® aircraft engines (please refer to the respective product presentations). They come in various sizes (mostly Metric) and are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different screws, such as hexagonal, allen, fixation and others are used in BRP-ROTAX® aircraft engines (please refer to the respective product presentations). They come in various sizes (mostly Metric) and are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different oil filters and other oil system parts are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different hoses for water, heat, air intake, protection, form, connecting, low pressure and others & related fittings are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU). ROTAX engine hoses are generally sold in meters and appearing prices are per meter but some hoses of specific dimensions and fittings are sold in pieces.

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.