The PARKER AIRBORNE designs and manufactures motor driven fuel fuel  boost and transfer pumps and is part of the PARKER AEROSPACE GROUP of the PARKER HANNIFIN CORPORATION. These pumps consist standard equipment by the world's leading airframe manufacturers. The PARKER AIRBORNE product range includes:

- In Line fuel pumps for low-flow fuel applications,

- Submerged Centrifugal fuel pumps,

- High Performance Centrifugal fuel pumps for use in turboprop or turbofan jet aircraft,

- Submerged Duplex fuel pumps with two distinct pumping elements

The PARKER AIRBORNE fuel boost pumps use 28 V direct current (DC) to drive a highly efficiency, brushless DC (BLDC) motor or 115.5 V alternating current (AC) three-phase induction motors. The BLDCmotor-driven pumps incorporate integral electronic controllers using Hall Effect sensor rotor-position feedback. The hardware-only controller doe not use any software or programmable logic devices. These pumps feature:

-fuel cooled motor and electronics

-fuel wetted carbon bearings allowing for long-life fluid film design with no rotating shaft seals

-a high efficiency brushless DC (BLDC) motor or a three-phase induction motor

-qualification for high levels of lighting and electromagnetic interference (EMI).

The PARKER AIRBORNE fuel boost pumps can be furnished as either NEW, NEW EXCHANGE or OVERHAUL EXCHANGE. 

Offered pumps in OVERHAUL Condition are supplied in accordance with FAA-approved process specification, come with a FAA Form 8130-3 and can be provided in exchange of existing customer owned units (cores). In all EXCHANGE cases,  the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders with us when our co-operating supplier verifies that the unit is in a reasonable condition. For additional information please consult the supplied documentation (*) or contact us.

In addition to the PARKER AIRBORNE pumps, RAPCO FAA-PMA approved pumps are also offered as direct replacements  to the respective PARKER AIRBORNE models. The RAPCO replacement pumps can be furnished as either NEW EXCHANGE or OVERHAUL EXCHANGE (please refer to their separate product presentation).

(*) The supplied documentation is to be used for reference only. When selecting a part for installation consult the appropriate aircraft maintenance manual, parts catalogue, or equipment list for approved data.

CLEVELAND WHEELS & BRAKES, part of PARKER HANNIFIN CORPORATION, offers an extensive range of FAA-PMA approved master brake cylinder assemblies for use in different aircraft.

CLEVELAND master cylinders come in push or pull types in different bore, stroke and displacement variations in inches and 7/16-10 or 1/8-27 N.P.T. port sizes. Some models include parking valves and reservoirs. 

For additional information please consult the supplied documentation on technical characteristics and suitability of the master cylinders for specific aircraft.

McFARLANE® AVIATION MC0543022-2 Series FAA-PMA approved nose wheel steering rods s are intended for use on for Cessna 172 series aircraft replacing respective OEM steering rod,tube assemblies.They feature new re-designed long-life springs, hardened internal washer for greater durability, stainless steel tubes for improved corrosion resistance  and optimum performance even after years of service.

Cessna Models' Application List:

172D,E,F,G,H,I,K,L,M,P

P172,

R172K

F172D,E,F,G,H,K,L,M,N,P

FP172

FR172E,F,G,H,J,K

172R

172S

TYCO ELECTRONICS TE CONNECTIVITY™ PIDG ring tongue terminals  are available in different colors, wire sizes (AWG) and stud sizes. Appearing sizes are in inches. Each TE CONNECTIVITY™ insulated terminal consists of a tin plated copper body, a tin plated copper wire support sleeve and a color-coded insulation sleeve. They meet respective MIL specification.

Aviation grade ELECTRODELTA X61 series solenoids by LAMAR TECHNOLOGIES LLC are offered in continuous  or intermitant duty in 12 or 24 Volt. They fit current GA production aircraft as well as legacy aircraft and replace both single terminal switched units, as well as the current double terminal switched units in production today. All units have multiple quality and functional tests prior to certification and delivery. Non FAA-PMA Approved.

Product Features:

Replace most contactors in general aviation

Available in 12 or 24 Volt

Available for Continuous or Intermittent duty

All units inspected and tested to performance standards

Warranty 24 months

ARKWIN INDUSTRIES has been designing and manufacturing engine actuators for over 60 years for operation with fuel, engine oil and hydraulic oil pressurization. Their actuators are used on numerous civil, military, and industrial applications to provide actuation force to direct engine control components. They differ from conventional hydraulic actuators, a major difference being the incorporation of the fire resistance features necessary to meet engine safety requirements. Engine actuators are frequently exposed to elevated temperature during normal operation. If extended periods of flame resistance are required, protective coatings can be applied to the actuator housings including the use of intumescence or ablative coatings. Where temperature permits, ARKWIN uses aluminum alloys. For higher operating  temperatures or pressure requirements exceeding the allowables of aluminum alloy, stainless PH steel alloys or titanium alloys can be provided. Two stage sealing is common for both static and dynamic seals. Specifically selected seal compounds allow zero external leakage, long durability life, high temperature resistance, while providing protection in fire. 

ARKWIN’s  engine actuators feature a high side load tolerance to ensure long piston life, high resistant wear plating, high reliability/low maintenance and fire resistance. Their key design characteristics include:

• Fuel and petroleum based operating fluids

• Operating pressures up to 4,000 psig

• Position feedback of the actuators is provided by integral or externally mounted LVDT’s.

• Multiple mounting options

• Servo valve applications (Control of actuators through external pressurization valving or through an integral electro hydraulic servo valve).

• Master/Slave configurations

ARKWIN’s  engine actuators are offered for different platforms including:

CFM International CFM56-2/-3, CFM56-5/-7

General Electric CF34-3, CF34-8C/E, CF6, F110, F404,  F414, LM2500, LM6000, TF34

ARKWIN EXCHANGE PROGRAM: ARKWIN’s commercial and industrial gas turbine engine actuator exchange program was developed for the CFM56-5/7, CF6-80C2, CF6-80E1, CF34-8C/E, LM2500, and LM6000 engines.  The program provides operators the reliability of OEM NEW products at competitive prices. Qualifying actuators are exchanged in a very short time for FACTORY NEW OEM production units complete with FACTORY NEW OEM and a three-year/6000 EOH warranty. For additional information please consult the supplied documentation or contact us.

Aircraft wheels and braking systems serve a vital function during takeoff, landing and taxiing. Along with landing gear, aircraft wheels and brakes are critical to ensure safe and reliable aircraft ground operations under extreme forces, stress, as well as wear and tear from general operation and the environment. 

Aircraft brakes are arranged in multiple disk pairs, which are commonly referred to as brake Heat Sink. As aircraft brakes convert the kinetic energy of the moving airplane to heat energy, they are also referred to as Heat Packs made of steel or carbon fibres. Conventional metal (steel) brakes are gradually replaced by carbon brakes (particularly on larger, long-haul commercial airplanes) due to their higher efficiency in braking applications, lower weight and resulting less fuel consumption and lower CO2 emission by the engines. 

Commercial aircraft wheels and braking systems are produced by by leading manufacturers such as Honeywell Aerospace, Collins Aerospace/Goodrich Wheels & Brakes, Parker Meggitt Aircraft Braking Systems and Safran Landing Systems (formerly Messier-Bugatti-Dowty) and offered as OEM products/parts for an extensive list of commercial aircraft platforms.  For more information on different OEM products please refer to the Product Description section, the supplied documentation or contact us.

Carbon and steel heat packs are also offered as part of our own labelled (AVIATIONEU NEW ERA) product lines. They are  PMA approved (*) parts by the Civil Aviation Administration of China (CAAC) for use on an extensive list of Western and Eastern commercial (civil ) aircraft platforms including Boeing, Airbus, McDonnell Douglas, Ilyushin and others. Sourced from quality suppliers they are available in an extensive product range, consist cost effective alternatives equalling or exceeding standards of the respective OEM products and feature high quality, safety, improved design, significant cost savings and fast deliveries. For more information on AVIATIONEU NEW ERA PMA brake heat packs please consult our separate product presentation or contact us.

FLYBOX® EFC-P Electronic Flap Controller by MICROEL SRL allows selection of the desired position of the flaps of an aircraft. EFC-P Controllers are offered in Rectangular (P/N: EFC-P-102010) or Round (P/N: EFC57-P-103010) versions. They are intended for use in ultralight and experimental aircraft. The working mode consist in selecting one of the four positions previously stored by the user, then the EFC-P will automatically moves the flaps in the exact position. The LEDs show the current position of the flaps or, when in movement, the position that they are reaching. For further information please refer to the attached documentation.

Aircraft braking systems serve a vital function during takeoff, landing and taxiing. Along with landing gear, aircraft wheels and brakes are critical to ensure safe and reliable aircraft ground operations under extreme forces, stress, as well as wear and tear from general operation and the environment. Commercial aircraft brakes are arranged in multiple disk pairs commonly referred to as Heat Sinks or Heat Packs (as they convert the kinetic energy of the moving airplane to heat energy). Initially made metal (steel) heat sinks are gradually replaced by those from carbon fibres (particularly on larger, long-haul commercial airplanes) due to their higher efficiency in braking applications, longer life-span, lower weight and resulting less fuel consumption and lower CO2 emission by the engines. 

Carbon and steel heat packs and parts are offered as part of our own labelled (AVIATIONEU NEW ERA) product lines. Sourced from quality suppliers these heat packs  feature high quality, safety, improved design, significant cost savings and fast deliveries. They can be used as  cost effective alternatives in many commercial aircraft platforms equalling or exceeding standards of  respective OEM products by leading manufacturers such as Honeywell Aerospace, Collins Aerospace/Goodrich Wheels & Brakes, Parker Meggitt Aircraft Braking Systems and Safran Landing Systems (formerly Messier-Bugatti-Dowty). They are  PMA approved (*) parts by the Civil Aviation Administration of China (CAAC) for use on an extensive list of Western and Eastern commercial (civil ) aircraft platforms including Boeing, Airbus, McDonnell Douglas, Ilyushin and others and are currently installed in aircraft operating by different air transport operators in China and other countries in the Middle-East, South and Central Asia and Africa.

Typical Aircraft Applications for steel and carbon heat packs include Boeing 737 / 757, Airbus A318 / A319 / A320 / A330 , McDonnell Douglas: MD82 /MD90  Xian MA60 etc. 

(*)  Parts Manufacturer Approval (PMA) is a combined design and production approval granted by a competent Civil Aviation Authority (CAA) to a manufacturer of aircraft parts for modification and replacement. Use of Civil Aviation Administration of China (CAAC) approved parts in other countries depends on existing bilateral agreements between CAAC and respective competent authorities in these countries.

For additional information please contact us.

UNIFRAX® is the largest ceramic fiber producer worldwide with in-house paper-making capabilities. UNIFRAX® products include FIBERFRAX®Ceramic Fiber Insulation Blankets (S Durablanket 2300F and 2600F, Fibermax Blanket 3000F), FIBERFRAX® Ceramic Fiber Insulation Papers in different grades, FIBERFRAX® Ceramic Fiber Insulation Boards (Duraboard LD and HD 2300F, Duraboard 2600F and 3000F), FyreWrap Insulation Ducts (Elite Grease, Elite Air Distribution System (ADS), Dryer Protection System (DPS), Plenum and Cable) and High Temperature Textiles (Ceramic Cloths 2300F, Ceramic Tapes 2300F, Ceramic Square and Round Braids 2300F, Ceramic Twisted Ropes 2300F, Silica Textiles 2000F and Fiberglass Textiles 1000F. UNIFRAX® products are distributed by Thermal Products Company, Inc.

For FIBERFRAX® Ceramic Fiber Insulation Papers please consult the Product Description section and supplied documentation. Other products can also be supplied on demand. Please contact us.

Fine quality switch from ACS used in many aircraft. The switch housing is machined from billet aluminum which makes this switch 25% lighter. It provides “ON” and “OFF” electrical control of both magnetos on a single engine aircraft. The key-operated switch mounts from the rear of the panel in a 7/8” dia hole. Available with or without starter position. A-510-2 model with starter position is supplied with switch plate two keys. (diode included). FAA PMA Approved. Made in USA.

SKY-TEC, a HARTZELL ENGINE TECHNOLOGIES brand, includes starters and support for Prestolite, Electrosystems, Lamar and Kelly designs. SKY-TEC OEM contactors are today installed in many general aviation aircraft while SKY-TEC FAA-PMA contractors can be used for starter, battery master/auxiliary or auxiliary power applications in replacement of OEM parts.

SKY-TEC STS-S Series FAA-PMA certified aircraft starter solenoids (aka relays) are intermittent duty suitable for starter applications. They are available in 12V (STS-S12) or 24V (STS-S24) versions. Activation: +V to S-Terminal (Frame is grounded by mounting).

SKY-TEC STS-M Series FAA-PMA approved Battery/Master solenoids are continuous duty solenoids intended for use in battery master/auxiliary applications in certified aircraft. They are available in 12V (STS-M12) or 24V (STS-M24) versions. Activation: -(Ground) to S-Terminal. (Floating ground frame).

SKY-TEC STS-A Series FAA-PMA approved solenoids are continuous duty and typically used for connecting auxiliary (ground) power. They are available in 12V (STS-A12) or 24V (STS-A24) versions. Activation: varies.

Product Features:

FAA-PMA Certified

All-metal case construction

Silver contacts (vs. copper) for high-current capability and long-life. They provide 300A in-rush capability. Much higher than the original units.

Strong spring and high-current coil for quick contact opening - minimizing arcing

Single coil terminal (other end connected to case)

High quality manufacturing 

Upgraded to perform best with today's lightweight, high torque starters

Same OE terminal layout simple to install

For additional information on different SKY-TEC series of slenoids and their applications in different aircraft please refer to the respective product presentations.

TEKNOFIBRA® is a leading manufacturer of aircraft firewall, exhaust, electrical, fuel system heat and sound absorbing materials. TEKNOFIBRA® product range includes Heat Reflecting Panels, Sleeves, Contacts and Aluminum Adhesive Tapes. The impressive heat-reflecting and insulating characteristics of Teknofibra® products ensure resistance and protection, even at extreme temperatures. Their lightness (lighter in weight than competition) makes them the perfect insulation for aeronautical uses. The organic composition of Teknofibra® non-woven fabric guarantees maximum safety and non-toxicity in every situation. In the event of a fire, no harmful emissions are produced, preserving total safety. Sound absorbing Teknofibra® panels dramatically reduce excessive noise that can distract and compromise results. TEKNOFIBRA® products are widely used in the Aviation, Car Racing and Motorcycling fields.

LORD manufactures a range of vibration and motion control products for General Aviation aircraft including elastomeric and non-elastomeric mounts, full structures, yokes and attachments. Their Dynafocal engine mounts are available for many aircraft, including the most produced general aviation fixed wing aircraft models, such as the Cessna 152, Cessna 172, Cessna 182, Piper PA-28 series, and more. For additional information please also refer to the attached Lord Catalog.

High quality vinyl toggle switch covers that do not have a nipple at the end of the cover. Suitable for MS35058 series switches. Available in different colors.

Electrodelta (Hartzell Engine Technologies) is the world market leader in top quality voltage regulators for general aviation aircraft, and continues to revolutionize the industry with proven technologies and improvements. The units are assembled from the highest quality electronic components available and are meticulously tested and calibrated to ensure maximum performance.The Electrodelta product line was acquired by by Lamar Technologies LLC in order to add new and alternative  parts to the company's product lines.

BRS AEROSPACE™ has first invented the first Whole Aircraft Rescue Parachute System (WARPS) in 1980 currently being installed on more than 35,000 aircraft. Today the company offers a wide range of WARPS suitable as retrofits to Cessna series 172 and Cessna 182, as standard installations on Cirrus SR20 and SR22 models but also for installations on LSA and experimental aircraft.

BRS WARPS are offered in 3 different types:

Canister. The BRS Canister is waterproof when the original factory seal remains intact, making it the perfect design for exterior installations. With a six year repack schedule and versatile mounting hardware, it is one of the most popular systems.

Softpack. The BRS Softpack is best suited for aircraft manufactur-ers that require a ballistic parachute mounted inside their aircraft. When mounted internally, this system also has a six year repack schedule.

VLS - Vertical Launch System. Built specifically for aircraft with limited interior space, the VLS (Vertical Launch System) installs on top of the wing or fuselage. Upward firing works well with pusher designed aircraft

A small solid-fuel rocket is used to pull the parachute out from its housing and deploy the canopy fully within seconds. Typically on ultralight installations the rocket is mounted on the parachute container. On larger aircraft installations the rocket may be remotely mounted. The current version, BRS-6. has a separate rocket installation that can be removed from the parachute so that the parachute can be sent for re-packing without the problems of trying to ship the rocket along with it. Typically the parachute requires repacking every six years and the rocket requires replacing every 12 years.

AVIATIONEU NEW ERA wire rope slings complements our range of wire cables/ropes providing mechanically spliced, hand spliced or socket robustly manufactured slings made from high grade 1770/1960 raw material. Hand and mechanically spliced slings are offered in different eye/loop types (soft,hard,plain thimble,solid thimble) in different diameters up to 60 mm. The hand spliced slings are of different contruction types (6X19,7X19,6X7) and feature sturdiness, strong construction, long service life and dimensional accuracy. They are offered as galvanized, UN galvanized, and stainless steel and can be used with different fittings (ring, hook, D shackle, turnbuckle). The mechanically spliced  galvanized steel and stainless steel slings are aasy to use, of different contruction types (6X7,7X7,6X19,7X19,6X37,7X37,6X36,7X36) and feature corrosion resistance, high strength and long service life.  The slings with socket from stainless steel are offered in  diameters 5-10 mm in plain eye, hard loop and plain thimble eye/loop types. Sold by the piece with Minimum Order Quantity (MOQ) 100 pieces.  Appearing price is for reference only per piece. Please contact us for a quotation.

Rest products are commonly used during travelling and leisure activities and span from small accessories such as travel pillows and camping mats to complete bed systems used in airlines, corporate jets, railways, ships and other means of transport.

In aircraft operating on long haul flights, secret compartments equipped with lie-flat beds are used for crew to rest and sleep. On smaller aircraft,  a few rows of passenger seats in the passenger cabin are reserved for crew rest. 

Different types of mattresses integrating respective technologies are offered by various manufacturers depending on their intended application.Air mattresses (aka Air beds) utilize a series of air chambers to provide sleepers with comfort and support.Their benefits include a lightweight design, low price, and easy storage. Memory foam mattresses are made up of several dense foam layers and provide benefits such as pressure relief from conforming to the body, enhanced spinal alignment, and motion isolation.Some models include cooling technologies to counteract heat retention. Commonly used as mattresses for crew rest in aviation meeting U.S. Federal Aviation Regulation FAR 25.853  that sets flammability standards for materials used in aircraft interiors. Hybrid mattresses offer a balance of comfort and support by combining foam layers with a pocketed coil system. Their benefits include pressure relief, better spinal alignment, improved airflow for cooling, and reduced motion transfer. Natural latex mattresses are environmentally friendly  and considered to last longer than traditional ones. Also offered from synthetic latex. These mattresses offer pressure relief by conforming to body curves while maintaining spinal alignment, are resistant to dust mites and mold, and have an open-cell structure for better airflow.

Complete bed systems in Aviation are commonly encountered in private jets, corporate aircraft , VIP cabins & lounges but also as commercial jet retrofits. Portable systems are equipped with a rechargeable battery-powered air pump as an inflation mechanism of the foundation and folding the ends of the mattress  in place over the aircraft seats. Bed accessories such as matrtress covers, pillows, and linen are also offered. 

Listed products and materials are supplied as OEM parts of their respective manufacturers or as parts of our own labelled (AVIATIONEU NEW ERA) product lines. For additional information please refer to the supplied documentation or contact us.

The PARKER HANNIFIN electronic plug amplifier VS 111 provides control for proportional pressure, directional, and throttle valves.

The plug amplifier may be mounted directly on the proportional solenoids and secured with a screw. The output of the amplifier supplies DC current for controlling one proportional solenoid.

This current is proportional to the command signal at the input of the amplifier. Through this, together with a proportional valve, an infinitely variable adjustment can be made to the pressure or flow.

Product Features:

• Solenoid control

• Simple installation, direct on valve

• Standard voltage or current signals for command signal inputs

• Capable of PLC control

• Solenoid current independent of temperature

• Solenoid connection 2+PE as per EN 175301-803

• Control connection 6+PE as per DIN 43651

IMPORTANT NOTE: Discontinued Item. Limited Availability from existing stocks in NEW SURPLUS  or USED Conditions.

For additional information please consult the supplied documentation or contact us.