The  PARKER HANNIFIN (Stratoflex Products Division) offers a broad array of PTFE, rubber and metal hose and hose assemblies in different outside diameters (OD), hose fittings, rigid tube assemblies, couplings, quick disconnects, swivel joints, fuel break-away valves, hydraulic fuses, and flow regulators, and specialty fittings including permanently swaged and welded fittings suitable for virtually any aerospace application. 

PARKER HANNIFIN Stratoflex rubber and PTFE hoses with various reinforcements and covers are briefly presented in the Product Description section with reference to their features and specifications. Offered in different sizes (tube and hose ODs) in inches and lengths in feet unless otherwise stated. Suitable fittings for use with Stratoflex hoses are separately presented. For additional information please refer to the attached Stratoflex catalogs for offered hoses, fittings and assemblies or contact us.

Hempel A/S is a leading solution provider for coatings used in an extensive range of protective, decorative, marine, container, industrial, and yacht applications. Sold under different brands Hempel's product portfolio includes topcoats, primers / intermediates, thinners, varnishes, linings, antifouling, CUI/heat/insulation products as well as products for pipe coating , cargo holds, cargo tanks, wind blades, road marking, and other uses. Hempel"s brands and respective products are briefly presented in the Product Description section.

Note: Required color shade must be specified at the time of ordering. Price variations apply depending on selected shade. Please consult the supplied documentation & contact us for quotation.

Anchor nuts (aka nutplates or anchor plates) are terms used interchangeably and relate to stamped sheet metal fasteners with an internally threaded tube and a plate with two clearance holes for rivets. They are used in blind mounted panel applications in aerospace and other industrial sectors where hex nuts cannot be used or an attached nut is required for ease of maintenance. 

Anchor nuts can be Fixed or Floating, the latter being easier to use due to their built-in nut (threaded hole) able to "float" slightly thus providing a convenient connection point for threaded rods, such as bolts, from the backside. In the case of Fixed anchor nuts, the built-in nut is static (i.e. without the capability to “float”) and the threaded rod must be positioned perfectly over the hole. Self-locking anchor nuts are those with a built-in locking mechanism preventing them from loosening over time from vibrations. They are extensively used in aerospace, automotive, and construction industries.

Depending on their intended application, nutplates conform to different military, aerospace, ISO or other industrial standards such as the German DIN, U.S. (ASME & ASTM, IFI, ANSI), British BS, Japanese JIS and others. They are offered as OEM parts under their respective brands or under our own labelled (AVIATIONEU NEW ERA) product lines intended as cost-effective alternatives to the respective OEM products. Listed in accordance with their standard of compliance, Fixed and Floating nutplates come in different materials (such as steel or CRES & finishes),  in single/double lug configurations and Metric ISO οr Unified thread sizes. There is currently no U.S. Military Standard (MS) specification for Metric nutplates.Depending on the selected product and availability, nutplates can be supplied with a dry film lube specified by the letter "L" in the respective part number. Those with countersunk rivet holes are specified by the letter "K" at the end of the part number.

Sourced from quality manufacturers, AVIATIONEU NEW ERA MS21071/MS21072 series nutplates are fixed self-locking, low height one-lug, reduced rivet spacing miniature anchor nuts. Those included in MS21071 series are manufactured from cadmium plated carbon steel while the MS21072 nutplates are produced from corrosion resistant steel (CRES). They are available in different Unified thread sizes, with plain or countersunk rivet holes on each side and come with or without a dry film lube. Sold in pieces but also in packs where the specified number of nuts per pack is indicated after the letters "PK" in the product reference number (SKU). Appearing prices are always for the units of measurement used each time. Matching rivets are sold separately.

For additional information please refer to the supplied documentation or contact us.

CHEMETALL® is the brand for the Surface Treatment global business unit of BASF's Coatings division & a leading supplier of applied surface treatment technologies for metal, plastic & glass substrates.

CHEMETALL® NAFTOSEAL® polysulphide sealants are specifically designed to meet the challenging  requirements of the aerospace industry for multi-purpose applications. The OEM and maintenance sectors both  benefit from a full range of easy-to-use and approved aircraft sealant technologies. The application characteristics of NAFTOSEAL® enable higher production rates. In addition NAFTOSEAL®  sealants offer  eco-friendly properties: all components are chromate-free, solvent-free or very low in solvent content. 

Key Features & Benefits:

 Free of chrome and solvents/low in solvent content

 Low temperature flexibility

 Fast tack-free and cure times for high production rates

 Good adhesion to various substrates

 Excellent chemical resistance

 High elasticity and resilience

 Good thixotropic properties, no slump

 Low and medium density products available

 Applications:

CHEMETALL® NAFTOSEAL® multi-purpose aircraft sealants can be used for all aircraft applications requiring sealants, such as fuel tank, fuselage, floor panels and aerodynamic smoothing. Adhesion promoters, tool and equipment cleaning technologies and mixing devices round-off our portfolio and cover all aspects for an efficient and safe sealant application.

Please refer to the supplied documentation for features and specifications of individual products.

AVIATIONEU NEW ERA SC screw lug type battery terminals are available in three versions: SC(JGA), SC(JGY) and SC(JGB). Please refer to the specifications table. They are made from brass (99.7% copper), tin plated and can be used with wire sizes 1.5-1000mm2 in a wide range of applications. Operating Temperature: :-55 to 150 deg. C. Sold in packs of 100 pieces each with Minimum Order Quantity (MOQ) 25 packs. The appearing price is for reference only. Please contact us for quotation.

Honed tubes/pipes are also known as  hydraulic or pneumatic cylinder tubing due to their primary uses for their production or repair. They are tubes with their inside diameter either honed or skived & roller burnished resulting in extremely precise inside diameter (ID) dimensions and smooth ID surfaces. Honing is an abrasive machining process involving the use of abrasive polishing stones and abrasive paper to remove small amounts of material and improve surface geometry and surface texture.The manufacturing process is determined upon the tube dimension, mold availability and customer ewquirements. Honed tubing is used in applications where a high precise inside diameter dimension and a smooth inside surface are required.

As honed tubes are the most important materials for manufacturing and repairing hydraulic and pneumatic cylinders, the quality of the honed tube is of critical importance. Honed  tubes/pipes are offered as part of our own branded (AVIATIONEU NEW ERA) product lines in different materials, such as steel, stainless steel and aluminum alloys in various grades and tempers depending on the intended application. Sourced from quality producers, the AVIATIONEU NEW ERA honed tubing is available in different size ranges in imperial  (in.) and metric systems and pre-determined or cut to order lengths. Depending on the producer, they comply with different standards/specifications. Manufacturing test reports can be supplied upon request additional cost, unless otherwise mentioned.

For additional information, please refer to the Product Description section, the supplied documentation or contact us.

TRELLEBORG o-rings are widely used seals as they are efficient and economical and can be used in a wide variety of static and dynamic applications to seal practically all liquid and gaseous media.They are available in elastomeric and other materials including (among others) EPDM, FKM and NBR, offered in sizes from 10 mm to 250 mm and suitable for use in operating conditions of -40 °C to 200 °C & 25 MPa max pressure. The o-rings are used predominantly for static sealing applications as a radial static seal, e.g. for bushings,covers,pipes,cylinders,rods or as an axial static seal, e.g. for flanges,plates,caps. Their applications include from repairs or maintenance to quality assured sealing applications in aerospace,automotive or general engineering.Compared with other sealing elements,the TRELLEBORG o-rings have a wide range of advantages:

- Simple,one-piece groove design reduces hardware and design costs

- Compact design allows smaller hardware

- Easy, failsafe installation reduces risk

- Applicable to a wide range of sealing problems: static, dynamic, single- or double-acting

- Wide compound choice for compatibility with most fluids

- Ex-stock availability of many sizes worldwide for easy maintenance and repair

Please refer to the attached Aerospace Part Number Guide.

The MS27643/AS27643 series airframe control bearings are offered by various manufacturers. They are  double row, ball, self-aligning, heavy duty bearings produced in accordance with AS7949 specification.

Depending on the manufacturer, rings and balls of these bearings are produced from premium quality AISI 52100 chrome steel or CRES 440C materials.  External surfaces (except bore, caps, and seals) are cadmium plated per AMS-QQ-P-416 or zinc nickel plated per OEM specifications. They include PTFE seals, CRES sealcaps and they are prelubricated. They are offered in different sizes but custom sizes, materials, tolerances, radial internal clearances, lubrication, plating, etc., can also be offered upon request.

Operating temperature range: -65 to +250 °F.

MIL-spec were initially developed to standardize wires and cables used in military equipment. For many years, wires used in aircraft met MIL-W-5086  mil-spec and SAE-AS50861 standards superseeding them. They were manufactured with the use of tin-coated copper conductors rated at 600 volts and temperatures of 105°C and various insulating coatings including polyvinyl chloride (PVC). The PVC insulation provided resistance to abrasion, among many other things. Still in production, MIL-W-5086  cables in their various types of conductors and jacket constructions are used, apart from the aircraft in other applications that require resistance to abrasion, cut-through, impact, chemicals, and fuels. They are gradually replaced by those made in accordance with Mil-W-22759 standard due to toxic fumes generated by PVC insulation in the event of a fire. The Mil-W-22759 standard transitioned to SAE AS22759 in 2004. These two standards are essentially identical and cover a of wide range of single conductor wires (please refer to the Product Description section and supplied documentation for assistance).

Sourced from quality producers, AS22759/M22759 wires are offered as part of our own labelled (AVIATIONEU NEW ERA) product lines in different configurations, various AWG(*) sizes, in white or other color variations (depending on their selected product reference number). They are suitable for use in a range of applications in military and civilian aircraft, in harsh aircraft engine environments, for control surfaces as well as applications in areas subject to severe weather and moisture-prone (SWAMP).

Those commonly used are SAE AS22759/16  unshielded wires (replacing wires produced as per M22759/16 /17/18 and /19  specifications) but other configurations can be available. This specification uses stranded tin plated copper or silver plated high strength alloy conductors and extruded ethylene/tetrafluorbethylene (ETFE) insulation. Respective wire ratings are 150° C and 600 Volts.

The AVIATIONEU NEW ERA AS22759/M22759 wires are sold in pre-determined lengths in feet indicated in the product reference number (SKU). They are commonly packed in carousels, reels or spools. Cut-to-order lengths in 10 ft increments are also offered. Accompanied by our Certificate of Conformance (CoC) free of charge or Manufacturer Certificate of Conformance (CoC) if required at additional charge. Some of the offered wires are additionaly QPL listed(**) as specified in their product title. 

(*) American Wire Gauge (AWG): Wire gauge is a measurement of wire diameter. This determines the amount of electric current a wire can safely carry, as well as its electrical resistance and weight.

(**) Included in U.S. DoD Qualified Products List (QPL) of products, components, or materials, often used in aerospace or military applications, examined, pre-tested & found to conform with all applicable standards or qualification requirements set by a certifying organization or government entity. 

AVIATIONEU NEW ERA end hose banjo fittings are intended for use in hydraulic pipes in automotive fuel, oil and hydraulic systems. They are available with single or double ends from different materials, mild steel, EN 1AL(free cutting steel), 11SMnPb30, EN 8, stainless steel 202 & 304. Sourced by certified manufacturers these banjo fittings are competitively priced and offered in different Metric sizes (M10x5/16", M12x5/16", M14x5/16", M14x3/8", M16x3/8", M18x3/8", M18x1/2") and different surface treatments (clear /yellow zinc plated, olive green zinc plated, dacromet). Sold by the piece (pc.) with Minimum Order Quantity (MOQ) 500 pcs.  Appearing price is for reference only per pc. Please contact us for a quotation.

EATON AEROQUIP® brand name represents quality and innovation for aerospace and other industrial applications with a wide range of hoses, fittings, couplings and connectors available to cover application requirements. Following the acquisition of Eaton’s hydraulics business by DANFOSS, EATON AEROQUIP® products form now part of DANFOSS product portfolio. 

DANFOSS EATON AEROQUIP® 491 and 471 hose fittings consist of an AN818 style nut, an externally threaded 37 nipple and an internally threaded hose socket. Fittings of sizes 3 through 6 have nuts and nipples of cadmium plated steel. Nuts and nipples for size 8 and larger are of anodized aluminum. Fittings conform to MS24587. Available in different tube and thread sizes in inches.

For additional information please consult the supplied documentation or contact us.

DANFOSS EATON SYNFLEX® subsea hoses and bundles are built to meet and exceed the most demanding industry requirements. Their rigorous hose qualification ensures long hose service life while their robust construction enables them to withstand high pressures. They are offered in long, continuous lengths to cover requirements of diverse applications all over the world.

At its core, SYNFLEX® High Pressure hose is a smooth, seamless, continuous extrusion of Nylon 11 Besno P40 TLO. The hose is reinforced with premium aramid fiber and jacketed with a highly UV resistant thermoplastic for long term aging and resistance to hydrolysis. Long continuous lengths are available for subsea bundles and single line applications. Available in 3,000, 5,000, 10,000, and 15,000 psi working pressures these hoses are lightweight, easy to install and assemble, and available in multiple sizes and long continuous lengths. Used in a wide range of applications including Hydraulic flying leads, workover umbilical components, hot lines, chemical, water and nitrogen injections and  subsea blow out prevention (BOP) bundles and hot lines enabling faster and more effective response to subsea events.

Like in other SYNFLEX® hoses, approved Eaton components are offered to ensure complete hose assembly systems. 

Hoses are priced and sold by the foot unless otherwise specified. Fittings can be separately purchased in pieces.

For additional information on different products please consult the Product Description section, supplied documentation or contact us.

AVIATIONEU NEW ERA high tensile stainless steel threaded bolts are manufactured from AISI 410 stainless steel and heat-treated and machined to minimum of 110-ksi or 760 Mpa tensile strength. They are dual ASTM & ASME certified (ASTM A193 B6: Class 1 Stainless Steel, ASME B1.1 2A/3A Inch Unified Threads and B1.13M 6h Metric Coarse Threads). In addition to their high tensile strength, they exhibit excellent resistance to corrosion, good dimensional stability, durability as well as a long functional work life. They can be used in different industries demanding high tensile strength and corrosion resistance like marine, chemical & petrochemical etc. Sold in in packs (pk) of 25 bolts/pk in different head, body diameters and thread lengths in inches with Minimum Order Quantity (MOQ) 10 packs. Please refer to the attached specifications table. Appearing price is for reference only and differentiates based on wanted bolt sizes. Please contact us for a quotation.

CHAMPION AEROSPACE designs and manufactures CHAMPION-brand filters and piston-engine ignition components for both OEM and aftermarket for general aviation aircraft applications.

CHAMPION FAA/PMA Approved Spin-On Oil Filters replace oil filter elements. They are easy to install and save time and clean-up.

Their full-pleat, resin-impregnated micronic filter media traps all harmful particles, including metallic chips which result from abnormal engine wear. Because the oil flows through many layers of locked-in fibers, there is no migration of fiber material to clog engine oil passages or affect bearing surfaces. According to industry-approved tests, the CHAMPION oil filters trap and hold more dirt and harmful particles during their normal operating time than any other similar filters. 

Product Features:

Replacement elements service engine-mounted or line-installed filter systems incorporating a permanent housing assembly.

All sizes of replacement elements are packed 12 per case of a single part number in heavy, re-shippable corrugated-board cartons

Modern spin-on oil filters contain the element, incorporating the anti-drain back valve mechanism (and internal bypass valve 48108-1/48109-1), and are sealed in a disposable housing.

All sizes of spin-on filters are packed 12 per case of a single part number in heavy, re-shippable corrugated-board cartons.

Silicone impregnated filter gasket aids in future removal.

Shorter stud length on CH 48110-1 for tight clearance applications.

Heavy, corrugated steel center tube supports each convoluted pleat of the filter element and produces a substantially higher collapse-pressure rating, twice that of other similar filters.

Maximum full-flow design, without interference from center-bolt oil filter assemblies, provides increased oil filtration each engine-operating hour.

Sold each or in packs of 12 filters per pack.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different oil filters and other oil system parts are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

Miniature incandescent and LED lams (bulbs) sourced from different manufacturers such as GENERAL ELECTRIC (GE), NORMAN LAMPS, AMGLO KEMLITE LABORATORIES,AERO-TECH LIGHT BULB Co. and others, for use in various aircraft applications (cockpit/wing/tail lights).

Unless a specific manufacturer is mentioned at the time of ordering and the selected lamp model is in production by this manufacturer, alternative lamps from different manufacturers shall be provided meeting the same or equivalent specifications.

 GE Lighting has been acquired by Tungsram. All bulbs are identical, but packaging may differ at the time of shipment.

EXXONMOBIL® MOBIL® offers a complete range of  lubricants specifically designed to lubricate wind turbines that help protect their critical parts, safeguarding their continuous operation. They provide excellent equipment  protection and oil efficiency in a wide range of conditions, including terrestrial, offshore, dry or liquids and at high or low temperatures. MOBIL® industrial lubricants are used in more than 40,000 wind turbines worldwide and they are suitable for many leading wind turbine manufacturers including Vestas, Repower, Suzlon, Enercon, GE Energy and Nordex. The range includes lubricant and gear oils for the main gearbox, to greases for the main pitch, yaw and pitch bearings and generator bearings, and hydraulic oils. 

For additional information please consult the Product Description section and the supplied documentation.

Polyurethane adhesives are becoming more popular due to their environmental attributes, compared to other products currently available. The advantage of using reinforced GRP polyurethane adhesive is to speed up the curing and production time when manufacturing GRP moldings.

In this category of adhesives, CTA reinforced GRP polyurethane adhesive 25-5 has been designed to bond GRP, FRP, composites, metals, plastics and many other materials within different industries and is often used for industrial fiberglass moldings, marine and automotive applications. This product will structurally bond gel-coat and fiber side, enabling less work in progress on the shop floor. Available in 50ml and 400ml cartridges and in various packages of 2, 6 or 12 cartridges per pack.

Product Features:

Odour free

No shrinkage

Ease of application