The AN6298 bulkhead nuts are plain, hexagon nuts used in various aerospace applications. These have been superseded by respective part numbers of SAE International standard  SAE-AS5178. Typically made from high-strength steel or corrosion-resistant alloys they are designed for use in  high-stress environments such as aircraft assemblies. Sourced from quality manufacturers they are offered as part of our own labelled (AVIATIONEU NEW ERA) product lines in different materials and thread sizes. The fitting composition is designated by a code letter in the part number of the fitting (No code letter for Steel, “D” for Aluminum Alloy, “J” for 304 Stainless Steel (CRES), “K” for 316 Stainless Steel or “T” for Titanium Alloy. Depending on their Part Number they are sold in pieces but mostly in packs a with specified number of fittings indicated after the letters "PK" in the product reference number (SKU).

The  Parker Aerospace (Stratoflex Products Division) offers a broad array of PTFE, rubber and metal hose and hose assemblies, hose fittings, rigid tube assemblies, couplings, quick disconnects, swivel joints, fuel break-away valves, hydraulic fuses, and flow regulators, and specialty fittings including permanently swaged and welded fittings suitable for virtually any aerospace application. 680 Series are 90º elbow flared fittings  for use with Stratoflex 156 hoses. They come in different outside diameters (OD) and thread sizes in inches. Please refer to the attached Stratoflex catalog for offered hoses and fittings or contact us.

Range of special accessories by FRANZ AIRCRAFT ENGINES for use in BRP-ROTAX® aircraft engines and other applications.

Thermoplastic hydraulic hoses are used in certain hydraulic control applications where low volumetric expansion properties are desired for more precise actions or control. Such applications include those for precision gauging, pilot lines, steering lines, grease systems, as well as other applications which cannot be subject to conductivity (use around power lines) or where moisture cannot be present, such as for spray foam. As with "rubber" hydraulic hose, not all brands of thermoplastic hydraulic hoses are built the same even though they may meet the same SAE specifications. Higher end brand hoses will typically be made to higher tolerances, better compounds, better resistance to various factors, added durability, enhanced engineering methods, and additional assurance of a proven system. With leading, innovative manufacturers such as Aeroquip, the market has seen improvements in hose design - such as more flexibility, lighter weight, higher temperature compounds, tougher covers, less manufacturing defects, and overall more durable products.

ΕΑΤΟΝ SYNFLEX® thermoplastic hose and tubing has been replacing rubber hose or metal tubing designs offering customers a number of benefits, including flexibility, durability, abrasion resistance, lighter weight materials, superior chemical resistance, variety of colors, high pressure capability and extended product performance.

Each component of the SYNFLEX® hose assembly system is compatible with other approved Eaton components to which it relates ensuring a complete hose assembly system. Component compatibility, along with the use of quality components, insures the production of reliable hose assemblies when properly assembled. Intermixing of fittings and hose not specifically engineered and designed for use with each other and Eaton equipment is not recommended and may result in the production of unsafe or unreliable hose assemblies. This can result in hose assembly leakage, hose separation or other failures which can cause serious bodily injury or property damage from spraying fluids, flying projectiles, or other substances. The ΕΑΤΟΝ warranty is limited to apply only when approved ΕΑΤΟΝ hose fittings and compatible ΕΑΤΟΝ SYNFLEX® hose are used with Eaton assembly equipment.

Hoses are priced and sold by the foot unless otherwise specified. Fittings can be separately purchased in pieces.

For additional information on different products please consult the supplied documentation or contact us.

The  Parker Aerospace (Stratoflex Products Division) offers a broad array of PTFE, rubber and metal hose and hose assemblies, hose fittings, rigid tube assemblies, couplings, quick disconnects, swivel joints, fuel break-away valves, hydraulic fuses, and flow regulators, and specialty fittings including permanently swaged and welded fittings suitable for virtually any aerospace application. 676 Series are straight fittings  for use with Stratoflex 156 hoses. They come in different outside diameters (OD) and thread sizes in inches. Please refer to the attached Stratoflex catalog for offered hoses and fittings or contact us.

The  PARKER HANNIFIN (Hose Products Divisionn) offers Push-Lok® Plus multipurpose hose lines featuring the widest fluid compatibility, application range and size range in the industry. At the same time they incorporate the highest working pressures in all sizes, making them the most versatile general-purpose hoses available. PARKER Push-Lok®  system is easy to use. No clamps or special tools are required during installation enabling assemblies in seconds, saving valuable time and cost. The unique seal of Push-Lok ensures reliable, durable, leak-free service while with PARKER:s exclusive color-code system hose inventories are identified and maintained easily and efficiently. 

PARKER's 801 general-purpose hoses with Push-Lok Plus technology are low-pressure, multipurpose synthetic rubber hoses featuring PARKER's exclusive color-coding system. Suitable for use with a wide range of media, 801 hoses are compatible with petroleum-based hydraulic fluid and lubricating oils, pneumatic power, antifreeze, and, when coupled with HY Series fittings, diesel fuel. These versatile hoses feature the unique Push-Lok® seal for easy assembly ensuring reliable, durable, and leak-free service. 801 hoses offer maximum working pressures ranging from 200 to 350 psi. The exclusive color-coding system enhances organization and assembly. Common uses include construction, utilities, machine tooling, ground support, industrial, and automotive applications.

For additional information please refer to the supplied documentation or contact us.

NYLO-SEAL tube fittings are exceptionally strong. The bodies, made of nylon, are stronger than machined fittings of similar composition. They are furnished complete with nut/sleeve assemblies, made of acetal copolymer. Since the sleeve snaps into and is retained by the nut there is no fumbling for a loose sleeve. Just insert tube into the fitting and tighten the nut 2 to 2-1/2 full turns. Note: The most frequently used combination of tube and pipe sizes are 1/4" Tube x 1/8" Pipe and 3/8" Tube x1/4" Pipe.

Hydraulic  & pneumatic fittings (also called compressed air connectors)  are used today in a wide range of applications as a connection for conductors such as hoses, tubes, pipes and machinery carrying fluids or gas and compressed air respectively to maintain their pressure without leakage. Whether their intended use is for fluids (hydraulic) or gas/compressed air (pneumatic) they are manufactured in a range of materials from plastic and aluminum to steel and stainless steel for maximum corrosion and chemical resistance. They come in different specifications (for military,aerospace or industrial uses), different thread types, such as British Standard Pipe (BSP) or U.S. National Pipe Thread (NPT/PTF) and sizes in inch or metric systems. Depending on the specific conductor/fitting application requirement different fittings are selected. Push-in fittings are quick and easy to install, connect and disconnect, even multiple times. Compressed air couplings,consisting of a socket and plug combination are self-sealing connecting components traditionally used for pneumatic tools, hall installations and laboratory equipment.  Compressed air distributors are the ideal choice whenever distribution of compressed air to different systems is required. Different types can be used to direct the compressed air from one access point to several  outputs at the required location.

Hydraulic  & pneumatic fittings are offered as OEM parts from well known manufacturers or as part of our own labelled (AVIATIONEU NEW ERA) product lines. They are included in different product presentations throughout our Web Platform. In addition, a comprehensive range of tools and accessories (separately presented) are also offered ranging from connecting and disconnecting pliers, tubing and pipe cutters to union nuts, sealing caps, hollow bolts, hose clips, tubing straps and others.

Extending our range of offered fittings for hydraulic systems and fluid power applications, JIC (Joint Industry Council) 37° flare fittings can be supplied as part of AVIATIONEU NEW ERA product porffolio. JIC fittings share the same 37° flare angle as AN (Army-Navy) fittings, listed separately but they exhibit significant differences in materials, design tolerances, and intended applications. Typically made from carbon steel, stainless steel, or brass, JIC 37° flare fittings are commonly used in agricultural equipment, construction, and general hydraulic industrial applications unlike AN fittings which were originally designed, developed and still widely used for military and aerospace applications meeting their strict performance requirements. Although JIC fittings are often interchangeable with AN fittings and also a cost-effective alternative for less demanding applications, AN fittings should be a prefered choice for aerospace,  military or critical applications in high-pressure or high-precision environments.

Please consult the supplied documentation or contact us for non listed items.

EATON HANSEN HA 15000  Series couplings, now part of DANFOSS product portfolio,  are general purpose hydraulic and fluid transfer couplings conforming to the dimensional requirements of ISO 7241-1 Series A. Body sizes are 1/4", 3/8", 1/2", 3/4" and 1".

Standard Materials used in their manufacturing include:

• Zinc-plated steel construction

• Stainless steel springs, balls and retaining rings

• Buna-N (Nitrile) seals

Product Features:

• Ball lock

• Manual connect, disconnect

• Poppet valving

• Slim profile

• Zinc plated steel construction

• NPTF and BSPP end connections

• Available push-to-connect socket designed for bulkhead mounting (1/2" body size only)

Rated Pressure in PSI / BAR per Body Size

1/4" - 4,568 / 315

 3/8" - 4,568 / 315

 1/2" - 3,625 / 250

 3/4" - 3,625 / 250

 1" - 2,900 / 200

For additional information please refer to the supplied documentation or contact us.

Note: Special Order items. Non-Cancellable/Non-Returnable Upon Order Placement (NCNR).

EATON AEROQUIP® brand name represents quality and innovation for aerospace and other industrial applications with a wide range of hoses, fittings, couplings and connectors available to cover application requirements. Eaton’s hydraulics were acquired by DANFOSS and form part of DANFOSS product portfolio.

DANFOSS EATON AEROQUIP® AE246/AE446/AE546/AE846 Series Hoses are based on AE246 advanced technology designed, tested and proved high pressure 3000 psi PTFE hose with Hi-Pac®braid reinforcement containing densely packed small diameter wires braided over a minimum thickness Teflon tube. This reinforcement offers up to 50% lighter in weight while the wires absorb stress more uniformly resulting in a stronger wire braid with less metal. Available in different tubing sizes and internal diameters in inches. They meet or exceed AS1339 performance requirements.

The AE546 series hoses feature an integral braided polyester chafe guard (manufactured by braiding polyester yarn onto existing hose styles) while those of  AE246 series come with an integral silicone firesleeve. 

The AE446 and AE846 Series hoses are AE246 high pressure teflon hoses with an integral silicone asbestos free fire protection (sleeve), adhering directly onto the hose metal braid and end fittings to form a smooth, tight bond.

Common end fittings used with these hoses include CRES fittings of -3 to -12 thread size, flared (MS33656), flareless (MS33514) or BSP type offered in straight, 45 deg and 90 deg styles.

“Super Gem” Reusable Flared Fittings can also be used with these hoses. They consist of 3 pieces: a socket, sleeve and nipple assembly.Made from corrosion resistant materials elbow fittings are available in standard, 45°, and 90° styles. Mate with AS4395 and AS33514 end connections. These service proven flared fittings provide permanent protection against leakage, even after high temperature aging and pressure impulsing to 250,000 cycles or more. This is due to the separation of the sealing function from the retention function.

The AEROQUIP® hoses are priced and sold by the foot unless otherwise specified. Fittings can be separately purchased in pieces.

For additional information please consult the Product Description section and the supplied documentation.

Hoses and fittings most suited to naval and marine applications are included in this listing. They are offered by DANFOSS EATON AEROQUIP® brand and other manufacturers, such as HYDRASEARCH or REPUBLIC BRASS SALES. Made from different materials & reinforcements they are available in different internal tube diameters (I.D.) in inches and lengths in feet. Depending on the hose, they can be used within their maximum operating pressure with a range of fluids (e.g. gasoline, crude, fuel and lubricating oils, air, water or hydraulic fluids) and conform to different Military specifications mentioned below. 

MIL-DTL-3992 Air brake hose 

MIL-DTL-8794 Medium-pressure wire-braid hose 

MIL-DTL-13444 Rubber fuel and oil hose 

MIL-DTL-13531 Rubber hydraulic hose 

MIL-DTL-52471 Rubber hydraulic hose 

MIL-H-24135 Wire-reinforced rubber hose 

MIL-H-24595 Wire-reinforced rubber hose 

MIL-H-24136 Fiber-reinforced rubber hose 

For additional information please consult the supplied documentation or contact us.

EATON products are known for their quality and innovation in aerospace and other industrial applications with a wide range of hoses, fittings, couplings and connectors available to cover application requirements. Following the acquisition of Eaton’s hydraulics business by DANFOSS, EATON hydraulic products form now part of DANFOSS product portfolio.

DANFOSS EATON WINNER® Series wire reinforced synthetic rubber hoses are constructed by a synthetic rubber tube with one or two wire braid reinforcement and a synthetic rubber cover. These hoses feature an operating temperature range of -40°C to +100°C / -40°F to +212°F. They can be used for a wide range of applications in hydraulic systems with petroleum and waterbased fluids as well as for general industrial uses. Available in different tubing sizes and internal diameters in inches. Priced and sold in meters unless otherwise stated.

EATON WINNER® Series include the following hoses:

The EATON WINNER® EC110 hoses which have one wire braid reinforcement and meet EN 853 1SN specification.

The EATON WINNER® EC115 hoses with one wire braid reinforcement and compliance with EN 857 1SC specification.

The EATON WINNER® EC210 hoses wiyh two wire braid reinforcement meeting EN 853 2SN specification.

The EATON WINNER® EC215 hoses with two wire braid reinforcement meeting  EN 857 2SC specification.

For additional information please refer to the supplied documentation ot contact us.

SAE-AS1034/MS24401/AN821 90° series elbow 90°, flared tube fittings are available as part of our own labelled (AVIATIONEU NEW ERA) product lines in different materials, tube outer diameters and thread sizes in inches.  AN821 and MS24401 series elbow fittings are superseded by the respective elbows of SAE International, standard AS1034 series. These fittings are made from different materials including Carbon Steel, Aluminum Alloy, Corrosion Resistant Steel (CRES), and Titanium Alloy. The 2 digits after the series code indicate the tubing outer diameter (O.D.)  in inches. The following Material Code Letters in the part numbers indicate the composition of the fitting. Finish code “V” in the PN indicates high purity Aluminum coating for “W” or “D” fittings. 

No code letter in part number for Carbon Steel

“D” for Aluminum Alloy (except 7075-T73)

“J” for CRES, type 304

“K” for CRES, type 316

“R” for CRES, type 321

“S” for CRES, type 347

“T” for Titanium Alloy 6AL-4V

“W” for Aluminum Alloy 7075-T73

For example, a 90° elbow fitting with a flared tube 3/8 in. size connection corresponds to PN AS1034D0606 when made from Aluminum Alloy or AS1034W0606 when made from 7075-T73 Aluminum Alloy replacing respective AN821-6D 90° elbow fitting from Anodized Aluminum Alloy with a 37 deg flared tube 3/8 in. connection, and a  UNJF / Class 3A thread of 9/16-18 in. size. AN821 fittings of tube outer diameters  3/4 in. (size 12) and above come with UNJ / Class 3A threads.

Depending on their Part Number they are sold in pieces but also in packs a with specified number of fittings indicated after the letters "PK" in the product reference number (SKU).

Note: In SAE AS standards for new designs, aluminum fittings with material code letter D in their Part or Identifying Number (PIN) are replaced by those with material code letter W for Aluminum Alloy 7075-T73 providing a higher tensile strength. In addition CRES fittings with material code letter S can be used for replacement parts. For new designs use of CRES fittings with material code letter R is recommended for applications requiring higher temperature. 

Flared sleeve fittings are cylindrical metallic parts designed to be used on tubing to back up the flared end and provide a bearing surface for the coupling nut, thereby reducing wear on the tubing flare. The inside diameter of the flanged end is countersunk to form a seat for the flare when assembled to a mating fitting.

Coupling sleeves conforming to SAE International, standard AS5176 standard replace respective MS20819/AN819 sleeves and they are offered as part of our own (AVIATIONEU NEW ERA) product lines. Sourced from quality producers these fittings are manufactured in different materials including 4130 Steel, Copper, Corrosion Resistant Steel (CRES) and Aluminum & Titanium Alloys. Material Code Letters in the part numbers indicate the composition of the fitting.

Depending on their Part Number they are sold in pieces but also in packs a with specified number of fittings indicated after the letters "PK" in the product reference number (SKU).

GATES industrial hoses are more than just flexible, reinforced tubes. GATES brand name is synonymous with engineered state-of-the-art quality hoses, couplings and accessories to cover an extensive range of application requirements ranging from water to welding, petroleum to pressure washing, and from mining to material handling. Every hose system component is tested under harsh environmental conditions and rigorous operational demands to ensure your Gates solution maximizes your value and minimizes your downtime. GATES couplings & ferrules feature simple coupling design and revolutionary performance. A brief overview of GATES hoses and couplings is provided at the Product Description section. For additional information please consult the supplied documentation or contact us.

In close co-operation with their respective quality manufacturers, AVIATIONEU NEW ERA industrial hoses address application requirements in many different industries. Combined with an extensive range of available fittings they consist cost-effective solutions with their high quality, cost savings and prompt deliveries.  Apart from the hoses, custom hose assemblies can be furnished with fittings pre-installed as per customer specifications.

Hoses are sold in feet or meters and fittings or hose assemblies in pieces. For additional information please consult the Product Description section or contact us for a quotation.

EATON AEROQUIP® brand name represents quality and innovation for aerospace and other industrial applications with a wide range of hoses, fittings, couplings and connectors available to cover application requirements. Following the acquisition of Eaton’s hydraulics business by DANFOSS, EATON AEROQUIP® products form now part of DANFOSS product portfolio.

DANFOSS EATON AEROQUIP® 816/8846/8891 series flared hose fittings can be used with DANFOSS EATON AEROQUIP® 601 hoses  and are available in different sizes. The 816 series straight hose fittings and 8891 series 90 Deg. hose fittings both consist of a pre-assembled nut/nipple assembly and an internally threaded hose socket. The size 4 fitting has a cadmium plated steel nut and nipple. Sizes 6, 8 and 10 nuts and nipples, and all sizes of sockets, are anodized aluminum. The 8846 series fittings are 45° hose fittings with swivel flared UNJF threads. They are noted for their outstanding performance as a result of a unique lipseal design concept. During assembly the nipple spur cuts a lip in the tube stock of the hose forming the fluid seal. 

For additional information please consult the supplied documentation or contact us.

Note: DANFOSS EATON AEROQUIP® 816 fittings ARE NOT THE SAME as AN816 fittings. Please specify at the time of ordering.

EATON AEROQUIP® brand name represents quality and innovation for aerospace and other industrial applications with a wide range of hoses, fittings, couplings and connectors available to cover application requirements. Following the acquisition of Eaton’s hydraulics business by DANFOSS, EATON AEROQUIP® products form now part of DANFOSS product portfolio.

DANFOSS EATON AEROQUIP® wire reinforced synthetic rubber hoses are offered in different series (types) described below to meet respective application requirements. 

The AE701 hoses consist an upgraded version and a direct replacement for old 601 ones, widely used for aircraft fuel and oil lines where flexibility and light weight are prime considerations. They are made from specially formulated synthetic rubber  inner tube with two layers of stainless steel wire outer braid reinforcement.  Because of their lighter weight and lower operating pressure than type 303 hose, AE701 hoses are not recommended for hydraulic lines. The AE501 hoses are AE701 hoses overlaid with a blue braided chafeguard cover of tough polyester yarn. Both AE701 and  AE501 hoses meet MIL-H-83797, TSO C53a,Type A specification.

The AE401 series hoses are AE701 hoses with an integral cover of silicone rubber compound. They meet MIL-H-83797, TSO C53a,Type C specification.

Product Features:

Flexibility

Light weight

Non-age sensitive (no shelf life)

Fluid temperatures: -65°F (-54°C) to +300°F (+149°C)

TSO C53a, Type A and Type C approvals (with fire sleeve)

Mil-Spec Approvals: MIL-H-83796/1 through MIL-H-83796/9 Assemblies & MIL-H-83797 Hose, MIL-F-83798 Fittings

Field attachable fittings

Applications:  fuel, engine oil and coolants. 

Available in different tubing sizes and internal diameters in inches. Priced and sold by the foot.

For additional information please refer to the supplied documentation ot contact us.

DANFOSS EATON SYNFLEX® subsea hoses and bundles are built to meet and exceed the most demanding industry requirements. Their rigorous hose qualification ensures long hose service life while their robust construction enables them to withstand high pressures. They are offered in long, continuous lengths to cover requirements of diverse applications all over the world.

At its core, SYNFLEX® High Pressure hose is a smooth, seamless, continuous extrusion of Nylon 11 Besno P40 TLO. The hose is reinforced with premium aramid fiber and jacketed with a highly UV resistant thermoplastic for long term aging and resistance to hydrolysis. Long continuous lengths are available for subsea bundles and single line applications. Available in 3,000, 5,000, 10,000, and 15,000 psi working pressures these hoses are lightweight, easy to install and assemble, and available in multiple sizes and long continuous lengths. Used in a wide range of applications including Hydraulic flying leads, workover umbilical components, hot lines, chemical, water and nitrogen injections and  subsea blow out prevention (BOP) bundles and hot lines enabling faster and more effective response to subsea events.

Like in other SYNFLEX® hoses, approved Eaton components are offered to ensure complete hose assembly systems. 

Hoses are priced and sold by the foot unless otherwise specified. Fittings can be separately purchased in pieces.

For additional information on different products please consult the Product Description section, supplied documentation or contact us.

MIL-DTL 6000D Soft Flexible Aircraft Fuel (*), Oil, Water & Alcohol Rubber Hoses (superseeding MIL-DTL-6000C hoses) are offered as part of our own labeled (AVIATIONEU NEW ERA) product lines. They replace the respective MIL-DTL 6000C hoses.

These hoses are designed to handle oil, alcohol, coolant, and water.  The tube of these hoses is oil resistant with a black cover reinforced with high strength mildew resistant yarns. It withstands extreme temperature conditions from -40 deg. F to +250 deg. F.  Lightweight, flexible and easy-to-handle, they meet or exceed U.S. military specs and consist the right choice for hard-to-get-to spots in tight engine compartments. Their burst pressure is 1000 PSI (400 PSI for the hose with ID 2-1/2 in.). 

AVIATIONEU NEW ERA MIL-DTL 6000D hoses are available in different internal and outer diameters in inches. Priced and sold in feet in one foot increments. The last part of our product reference code (SKU) indicates the inner diameter of the hose in inches.

For additional information please refer to the supplied documentation or contact us.

(*) MIL-DTL 6000D hoses are not recommended for use as fuel lines.