AN823 45° Flared Tube & Pipe Thread Elbow Fittings are superseded by those of Military Standard MS20823 and these are superseded in turn by SAE-AS5196 standard. These fittings are  offered as part of AVIATIONEU NEW ERA product lines in steel or aluminum in different tube outer diameters and thread sizes in inches. Aluminum fittings are designated by the letter "D" after the suffix number.

VENA® HT Series flexible  hoses (SCAT equivalent) are  made of one layer of glass fabric silicone coated and visible steel wire  spiral inside. For use in conducting extremely cold or hot air (temperature range: -65°F to +550°F). Available in different internal diameters in inches. Sold by the foot.

Hose and tubing insert fittings are available in high density black polyethylene or white nylon. Polyethylene fittings can be used with tygon, nylon or soft rubber tubing to assemble low pressure instrument lines such as airspeed pitot and static lines. Nylon fittings can be used in gravity-feed fuel lines and engine breather lines.

EATON products are known for their quality and innovation in aerospace and other industrial applications with a wide range of hoses, fittings, couplings and connectors available to cover application requirements. Following the acquisition of Eaton’s hydraulics business by DANFOSS, EATON hydraulic products form now part of DANFOSS product portfolio.

DANFOSS EATON WINNER® Series wire reinforced synthetic rubber hoses are constructed by a synthetic rubber tube with one or two wire braid reinforcement and a synthetic rubber cover. These hoses feature an operating temperature range of -40°C to +100°C / -40°F to +212°F. They can be used for a wide range of applications in hydraulic systems with petroleum and waterbased fluids as well as for general industrial uses. Available in different tubing sizes and internal diameters in inches. Priced and sold in meters unless otherwise stated.

EATON WINNER® Series of hoses include the following hoses:

EC110 and EC115 one wire braid reinforcement hoses meeting EN 853 1SN and EN 857 1SC specifications respectively,

EC210 and EC215  two wire braid reinforcement hoses complying with EN 853 2SN & EN 857 2SC specifications respectively.

An extensive range of EATON WINNER® hydraulic fittings are also available under different basic part numbers conforming to US and other standards/specifications.For additional information please refer to the Product Description section and the supplied documentation or contact us.

The  Parker Aerospace (Stratoflex Products Division) offers a broad array of PTFE, rubber and metal hose and hose assemblies, hose fittings, rigid tube assemblies, couplings, quick disconnects, swivel joints, fuel break-away valves, hydraulic fuses, and flow regulators, and specialty fittings including permanently swaged and welded fittings suitable for virtually any aerospace application. 680 Series are 90º elbow flared fittings  for use with Stratoflex 156 hoses. They come in different outside diameters (OD) and thread sizes in inches. Please refer to the attached Stratoflex catalog for offered hoses and fittings or contact us.

SAE-AS1034/MS24401/AN821 90° series elbow 90°, flared tube fittings are available as part of our own labelled (AVIATIONEU NEW ERA) product lines in different materials, tube outer diameters and thread sizes in inches.  AN821 and MS24401 series elbow fittings are superseded by the respective elbows of SAE International, standard AS1034 series. These fittings are made from different materials including Carbon Steel, Aluminum Alloy, Corrosion Resistant Steel (CRES), and Titanium Alloy. The 2 digits after the series code indicate the tubing outer diameter (O.D.)  in inches. The following Material Code Letters in the part numbers indicate the composition of the fitting. Finish code “V” in the PN indicates high purity Aluminum coating for “W” or “D” fittings. 

No code letter in part number for Carbon Steel

“D” for Aluminum Alloy (except 7075-T73)

“J” for CRES, type 304

“K” for CRES, type 316

“R” for CRES, type 321

“S” for CRES, type 347

“T” for Titanium Alloy 6AL-4V

“W” for Aluminum Alloy 7075-T73

For example, a 90° elbow fitting with a flared tube 3/8 in. size connection corresponds to PN AS1034D0606 when made from Aluminum Alloy or AS1034W0606 when made from 7075-T73 Aluminum Alloy replacing respective AN821-6D 90° elbow fitting from Anodized Aluminum Alloy with a 37 deg flared tube 3/8 in. connection, and a  UNJF / Class 3A thread of 9/16-18 in. size. AN821 fittings of tube outer diameters  3/4 in. (size 12) and above come with UNJ / Class 3A threads.

Depending on their Part Number they are sold in pieces but also in packs a with specified number of fittings indicated after the letters "PK" in the product reference number (SKU).

Note: In SAE AS standards for new designs, aluminum fittings with material code letter D in their Part or Identifying Number (PIN) are replaced by those with material code letter W for Aluminum Alloy 7075-T73 providing a higher tensile strength. In addition CRES fittings with material code letter S can be used for replacement parts. For new designs use of CRES fittings with material code letter R is recommended for applications requiring higher temperature. 

Nylaflow®, Nylon Tubing is a high-quality pressure tubing, available in several types. Nylaflow® tubes are tough and durable, offering low friction and high flexibility. Offered by different producers, Nylaflow® tubing is suitable for applications that require toughness, resilience, a small bend radius and high burst strength. Nylaflow® tubing offers superior burst strength compared to vinyl, ethylene, and urethane tubing and it is a high performance, long-lasting alternative to copper, rubber, aluminum and other types of plastic tubing. Its high burst rating makes it a common solution pneumatic and hydraulic lines. Nylon has excellent chemical resistance and can withstand exposure to relatively high concentrations of harsh chemicals at elevated temperatures. Its extremely smooth inner surface resists abrasion and wear and makes for a low coefficient of friction. It is often used in corrosive environments because of its excellent resistance to harsh chemicals. 

Nylaflow® tubing comes in different types.

Types T (Thin Wall) and H (Heavy Wall) are the most common Nylaflow general purpose tubing made from type 6/6 nylon. FDA compliant for use in food or beverage handling applications also meeting 3A sanitary standards. The High performance of this Nylon tubing makes it perfect for applications that require durability, resilience, a small bend radius, and high burst strength.

Type LM tubing is a premium high flex tubing available in two types: natural or black, which exhibits improved light stability. Type LM offers excellent chemical resistance and low moisture absorption. Often used in automotive fuel lines, lubrication lines, air lines, and vacuum environments.

Type LP tubing is a low pressure, general purpose type 6 nylon tubing with carbon added for UV stability. 

Nylaflow® nylon tubing is available with custom markings, cut to length and custom packaging. It can be cut with a sharp knife and flared hot or cold. They are odorless, tasteless and noncorrosive.

Typical applications of Nylaflow® tubing include airlines, grease lines, vacuum lines, and hydraulic lines.

The  PARKER HANNIFIN (Stratoflex Products Division) offers a broad array of PTFE, rubber and metal hose and hose assemblies in different outside diameters (OD), hose fittings, rigid tube assemblies, couplings, quick disconnects, swivel joints, fuel break-away valves, hydraulic fuses, and flow regulators, and specialty fittings including permanently swaged and welded fittings suitable for virtually any aerospace application. 

PARKER HANNIFIN Stratoflex rubber and PTFE hoses with various reinforcements and covers are briefly presented in the Product Description section with reference to their features and specifications. Offered in different sizes (tube and hose ODs) in inches and lengths in feet unless otherwise stated. Suitable fittings for use with Stratoflex hoses are separately presented. For additional information please refer to the attached Stratoflex catalogs for offered hoses, fittings and assemblies or contact us.

The  PARKER HANNIFIN (Hose Products Divisionn) offers Push-Lok® Plus multipurpose hose lines featuring the widest fluid compatibility, application range and size range in the industry. At the same time they incorporate the highest working pressures in all sizes, making them the most versatile general-purpose hoses available. PARKER Push-Lok®  system is easy to use. No clamps or special tools are required during installation enabling assemblies in seconds, saving valuable time and cost. The unique seal of Push-Lok ensures reliable, durable, leak-free service while with PARKER:s exclusive color-code system hose inventories are identified and maintained easily and efficiently. 

PARKER's 801 general-purpose hoses with Push-Lok Plus technology are low-pressure, multipurpose synthetic rubber hoses featuring PARKER's exclusive color-coding system. Suitable for use with a wide range of media, 801 hoses are compatible with petroleum-based hydraulic fluid and lubricating oils, pneumatic power, antifreeze, and, when coupled with HY Series fittings, diesel fuel. These versatile hoses feature the unique Push-Lok® seal for easy assembly ensuring reliable, durable, and leak-free service. 801 hoses offer maximum working pressures ranging from 200 to 350 psi. The exclusive color-coding system enhances organization and assembly. Common uses include construction, utilities, machine tooling, ground support, industrial, and automotive applications.

For additional information please refer to the supplied documentation or contact us.

EATON AEROQUIP® brand name represents quality and innovation for aerospace and other industrial applications with a wide range of hoses, fittings, couplings and connectors available to cover application requirements. Following the acquisition of Eaton’s hydraulics business by DANFOSS, EATON AEROQUIP® products form now part of DANFOSS product portfolio.

DANFOSS EATON AEROQUIP® FD45 Series quick disconnect couplings are  general purpose industrial interchange couplings offered in different sizes, materials, port  and multiple valved and non-valved configurations. They are replaced by EATON Hansen HK 1-8 Series couplings which set the industry standard for ISO B Couplings.

They feature a rugged PUSH-PULL design ball latch mechanism allowing quick and easy connection and disconnection of hose lines. Their automatic self-sealing poppet valves provide excellent high and low pressure sealing. Standard seal materials include Buna-N, EPR and Viton. Standard body materials Include:

- High resistance carbon steel with zinc trivalent chromate plating (Brass poppet guide in –02 size)

- Brass with stainless steel springs and balls for greater corrosion resistance in rugged applications and fluid compatibility where stainless steel is cannot be used

- 303/304 Stainless Steel for excellent corrosion resistance in rugged applications and fluid compatibility. 

The FD45 series couplings meet requirements to ISO standard 7241/1 Series B Interchange.

For additional information please refer to the supplied documentation or contact us.

Note: Special Order items. Non-Cancellable/Non-Returnable Upon Order Placement (NCNR). Minimum Order Quantities & long lead times usually apply.

In close co-operation with their respective quality manufacturers, AVIATIONEU NEW ERA industrial hoses address application requirements in many different industries. Combined with an extensive range of available fittings they consist cost-effective solutions with their high quality, cost savings and prompt deliveries.  Apart from the hoses, custom hose assemblies can be furnished with fittings pre-installed as per customer specifications.

Hoses are sold in feet or meters and fittings or hose assemblies in pieces. For additional information please consult the Product Description section or contact us for a quotation.

EATON AEROQUIP® brand name represents quality and innovation for aerospace and other industrial applications with a wide range of hoses, fittings, couplings and connectors available to cover application requirements. Following the acquisition of Eaton’s hydraulics business by DANFOSS, EATON AEROQUIP® products form now part of DANFOSS product portfolio.

DANFOSS EATON AEROQUIP® BLIND-MATE quick disconnect couplings are utilized in advanced liquid cooled electronics and avionics thermal management systems. These couplings are used between removable cold plates and fixed manifolds to allow for quick leak free removal and replacement of both evaporative and liquid flow through systems. Blind-mate couplings provide unequaled performance in pressure drop, radial misalignment, and envelope. In addition, these couplings incorporate a patented integral thermal relief feature that prevents pressure buildup when the liquid cooling module is disconnected. Like other EATON AEROQUIP® quick disconnect couplings, they can be ordered as separate halves. Available in different sizes.

AEROQUIP® BLIND-MATE  couplings have been tested to meet or exceed SAE AS5072 for modular style couplings. These requirements include:

• Ability to operate within a temperature range of –65°F to +160°F (-54°C to +71°C)

• Capable of enduring 1000 connect/disconnect cycles without evidence of malfunction, leakage or damage

• Standard operating pressure of 150 PSI, proof pressure of 225 PSI, and burst pressure of 375 PSI

• Ability to tolerate proof and burst pressure without rupture or loss of fluid

• Ultra-low spillage during disconnection

• Integral thermal relief valve

• Minimal air inclusion during connection

Applications: Ethylene Glycol Water, Propylene Glycol Water, Polyalphaolefin (PAO) per MIL-C-87252

For additional information please refer to the supplied documentation or contact us.

Note: Special Order items. Non-Cancellable/Non-Returnable Upon Order Placement (NCNR). Minimum Order Quantities & long lead times usually apply. Contact us. 

REFFLEX® INTERNATIONALl B.V. manufactures prefabricated hoses, tubes, fittings and tools for refrigeration applications. Their REFFLEX® advanced systems of refrigeration flexible hoses are offered in two sizes, DN-2.0mm, and DN-5.0mm while larger sizes are covered by their COLDLEX® system. They are both strong and reliable, easy to use, ozone, UV and oil resistant, with a highly flexible, short bending radius and capability of absorbing all possible multi directional vibrations. They are vailable in different colors.

DN-2.0mm is used for connecting pressostats, pressure gauges etc. while DN 5.0mm is mainly used for connecting oil separators and level regulators.

REFFLEX® fittings 1/4 “flare, 6mm ODS, 1/4 “flare or 3/8” flare are also offered for use with their DN-2.0mm, DN-5.0mm hoses together with different tools.

For additional information please refer to the supplied documentation.

AVIATIONEU NEW ERA air relief valves can be used in different industrial applications. They are made from different materials,  EN 1AL (free cutting steel), 1SMnPb30+C or SAE 12L13  and zinc plated. Available in the following sizes:

Metric: M10 x 1 ARV

British Standard Pipe (BSP): 1/8" BSP ARV

U.S. National Pipe Thread (NPT): 1/8" NPT ARV, 1/4" NPT ARV

Sold by the piece (pc.) with Minimum Order Quantity (MOQ) 1000 pcs.  Appearing price is for reference only per pc. Please contact us for a quotation.

SAE-AS1035/MS24402/AN824 series tee, flared tube fittings are available as part of our own labelled (AVIATIONEU NEW ERA) product lines in different materials, tube outer diameters and thread sizes in inches. The AN824 series tee fittings are superseded by the respective fittings of SAE-AS1035 series (SAE International, Standard SAE AS1035, FITTING, TEE, STANDARD AND REDUCER, FLARED). They are manufactured from Carbon Steel, Aluminum Alloy, Corrosion Resistant Steel (CRES), Titanium Alloy. The 2 digits after the series code indicate the tubing outer diameter (O.D.)  in inches. The following Material Code Letters in the part numbers indicate the composition of the fitting. Finish code “V” in the PN indicates high purity Aluminum coating for “W” or “D” fittings. 

Depending on their Part Number they are sold in pieces but also in packs a with specified number of fittings indicated after the letters "PK" in the product reference number (SKU).

No code letter in part number for Carbon Steel

“D” for Aluminum Alloy (except 7075-T73)

“J” for CRES, type 304

“K” for CRES, type 316

“R” for CRES, type 321

“S” for CRES, type 347

“T” for Titanium Alloy 6AL-4V

“W” for Aluminum Alloy 7075-T73

For example, AS1035D in the PN of the fitting indicates that these are made from Aluminum Alloy. 

Note: In SAE AS standards for new designs, aluminum fittings with material code letter D in their Part or Identifying Number (PIN) are replaced by those with material code letter W for Aluminum Alloy 7075-T73 providing a higher tensile strength. In addition CRES fittings with material code letter S can be used for replacement parts. For new designs use of CRES fittings with material code letter R is recommended for applications requiring higher temperature. 

Hydraulic  & pneumatic fittings (also called compressed air connectors)  are used today in a wide range of applications as a connection for conductors such as hoses, tubes, pipes and machinery carrying fluids or gas and compressed air respectively to maintain their pressure without leakage. Whether their intended use is for fluids (hydraulic) or gas/compressed air (pneumatic) they are manufactured in a range of materials from plastic and aluminum to steel and stainless steel for maximum corrosion and chemical resistance. They come in different specifications (for military,aerospace or industrial uses), different thread types, such as British Standard Pipe (BSP) or U.S. National Pipe Thread (NPT/PTF) and sizes in inch or metric systems. Depending on the specific conductor/fitting application requirement different fittings are selected. Push-in fittings are quick and easy to install, connect and disconnect, even multiple times. Compressed air couplings,consisting of a socket and plug combination are self-sealing connecting components traditionally used for pneumatic tools, hall installations and laboratory equipment.  Compressed air distributors are the ideal choice whenever distribution of compressed air to different systems is required. Different types can be used to direct the compressed air from one access point to several  outputs at the required location.

Hydraulic  & pneumatic fittings are offered as OEM parts from well known manufacturers or as part of our own labelled (AVIATIONEU NEW ERA) product lines. They are included in different product presentations throughout our Web Platform. In addition, a comprehensive range of tools and accessories (separately presented) are also offered ranging from connecting and disconnecting pliers, tubing and pipe cutters to union nuts, sealing caps, hollow bolts, hose clips, tubing straps and others.

Extending our range of offered fittings for hydraulic systems and fluid power applications, JIC (Joint Industry Council) 37° flare fittings can be supplied as part of AVIATIONEU NEW ERA product porffolio. JIC fittings share the same 37° flare angle as AN (Army-Navy) fittings, listed separately but they exhibit significant differences in materials, design tolerances, and intended applications. Typically made from carbon steel, stainless steel, or brass, JIC 37° flare fittings are commonly used in agricultural equipment, construction, and general hydraulic industrial applications unlike AN fittings which were originally designed, developed and still widely used for military and aerospace applications meeting their strict performance requirements. Although JIC fittings are often interchangeable with AN fittings and also a cost-effective alternative for less demanding applications, AN fittings should be a prefered choice for aerospace,  military or critical applications in high-pressure or high-precision environments.

Please consult the supplied documentation or contact us for non listed items.

Flared sleeve fittings are cylindrical metallic parts designed to be used on tubing to back up the flared end and provide a bearing surface for the coupling nut, thereby reducing wear on the tubing flare. The inside diameter of the flanged end is countersunk to form a seat for the flare when assembled to a mating fitting.

Coupling sleeves conforming to SAE International, standard AS5176 standard replace respective MS20819/AN819 sleeves and they are offered as part of our own (AVIATIONEU NEW ERA) product lines. Sourced from quality producers these fittings are manufactured in different materials including 4130 Steel, Copper, Corrosion Resistant Steel (CRES) and Aluminum & Titanium Alloys. Material Code Letters in the part numbers indicate the composition of the fitting.

Depending on their Part Number they are sold in pieces but also in packs a with specified number of fittings indicated after the letters "PK" in the product reference number (SKU).

EATON AEROQUIP® brand name represents quality and innovation for aerospace and other industrial applications with a wide range of hoses, fittings, couplings and connectors available to cover application requirements. Eaton’s hydraulics were acquired by DANFOSS and form part of DANFOSS product portfolio.

DANFOSS EATON AEROQUIP® AE246/AE446/AE546/AE846 Series Hoses are based on AE246 advanced technology designed, tested and proved high pressure 3000 psi PTFE hose with Hi-Pac®braid reinforcement containing densely packed small diameter wires braided over a minimum thickness Teflon tube. This reinforcement offers up to 50% lighter in weight while the wires absorb stress more uniformly resulting in a stronger wire braid with less metal. Available in different tubing sizes and internal diameters in inches. They meet or exceed AS1339 performance requirements.

The AE546 series hoses feature an integral braided polyester chafe guard (manufactured by braiding polyester yarn onto existing hose styles) while those of  AE246 series come with an integral silicone firesleeve. 

The AE446 and AE846 Series hoses are AE246 high pressure teflon hoses with an integral silicone asbestos free fire protection (sleeve), adhering directly onto the hose metal braid and end fittings to form a smooth, tight bond.

Common end fittings used with these hoses include CRES fittings of -3 to -12 thread size, flared (MS33656), flareless (MS33514) or BSP type offered in straight, 45 deg and 90 deg styles.

“Super Gem” Reusable Flared Fittings can also be used with these hoses. They consist of 3 pieces: a socket, sleeve and nipple assembly.Made from corrosion resistant materials elbow fittings are available in standard, 45°, and 90° styles. Mate with AS4395 and AS33514 end connections. These service proven flared fittings provide permanent protection against leakage, even after high temperature aging and pressure impulsing to 250,000 cycles or more. This is due to the separation of the sealing function from the retention function.

The AEROQUIP® hoses are priced and sold by the foot unless otherwise specified. Fittings can be separately purchased in pieces.

For additional information please consult the Product Description section and the supplied documentation.

DANFOSS EATON SYNFLEX® 1300 Series composite wall tubes are designed for pneumatic instrument control systems. Their fully bonded polyethylene/aluminium construction combines the advantages of both metal and plastic tubing.

Their outer, high density polyethylene layer is impervious to most chemical environments and enables SYNFLEX® 1300 tubes to outperform practically all types of unprotected metal tubing.

Product Features:

• Combine the advantages of both metal and plastic tubing

• Very light (5 times lighter than a standard instrument control tubes)

• Provide neat looking bends without special bending tools

• Corrosion and chemical environment resistant

• Excellent chemical compatibility

• Tubing contents dry thanks to aluminum barrier

• Enable direct burial w ithout additional protection (whatever the installation)

• Connection with standard compression fittings

• 25, 75,100m standard lengths

• Standard color: black, other colours on request

• Also available with "Halogen free" jacket

Applications

• Pneumatic instrumentation and control lines located in very wet or moist environments

• Air and gas sampling

• Corrosive environments

• ID surface best suited for air

Construction

• Polyethylene/Aluminum composite

Temperature range

• -40 °C to 80 °C

SAE-AS5174/MS24392/AN815 series union, flared tube male to male hydraulic fittings are available as part of our own labelled (AVIATIONEU NEW ERA) product lines in different materials, tube outer diameters and thread sizes in inches. The AN815 series fittings are superseded by the respective fittings of Military Standard MS24392 which in turn are superseded by SAE International standard  SAE-AS5174 series. Materials include: Carbon Steel, Aluminum Alloy, Corrosion Resistant Steel (CRES), Titanium Alloy. The 2 digits after the series code indicate the tubing outer diameter (O.D.)  in inches. The following Material Code Letters in the part numbers indicate the composition of the fitting. Finish code “V” in the PN indicates high purity Aluminum coating for “W” or “D” fittings. 

Depending on their Part Number they are sold in pieces but also in packs a with specified number of fittings indicated after the letters "PK" in the product reference number (SKU).

No code letter in part number for Carbon Steel

“D” for Aluminum Alloy (except 7075-T73)

“J” for CRES, type 304

“K” for CRES, type 316

“R” for CRES, type 321

“S” for CRES, type 347

“T” for Titanium Alloy 6AL-4V

“W” for Aluminum Alloy 7075-T73

“Z” for Carbon Steel, Zinc plated

For example, AS5174D0606 union fitting is made from Aluminum Alloy with a tubing outer diameter (O.D.) 3/8" and a 0.5625-18 UNJF thread. The corresponding union fitting in AN832 series would be AN815-6D.

Note: In SAE AS standards for new designs, Aluminum fittings with material code letter D in their Part or Identifying Number (PIN) are replaced by those with material code letter W for Aluminum Alloy 7075-T73 providing a higher tensile strength. In addition CRES fittings with material code letter S can be used for replacement parts. For new designs use of CRES fittings with material code letter R is recommended for applications requiring higher temperature.