All aircraft develop fuel leaks at one time or another which can ground an aircraft for unspecified time intervals. Fuel leaks are considered to be one of the most time consuming maintenance tasks required on an aircraft. Fuel line leak testers are intended to check leakages in fuel lines and assist maintenance personnel of Maintenance, Repair and Overhaul (MRO) facilities to detect and repair them. AVIATIONEU NEW ERA fuel line leak testers are offered as  part of our own label product portfolio of Aircraft MRO Equipment. For more information and a quotation please contact us.

TRONAIR® is a leading GSE manufacturer offering a diverse range of high-quality GSE product lines to support safe and efficient aircraft ground operations. Their product portfolio includes equipment for jacking & access, hydraulic & pressure testing, towing & taxiing, electrical power & air conditioning, and aircraft & engine servicing.

TRONAIR® ATA-29 Hydraulic Power Service Units (HPUs) are multipurpose equipment, used for loading hydraulic oil in the aircraft or engine tanks of commercial, regional, and business airlines or allowing the aircraft actuators to be moved through their equipped high-pressure pumps. Their filter lines ensure that the liquid is not contaminated while their use reduces aircraft filter changes and increases aircraft component life. TRONAIR® ATA 29 HPUs have the best high-grade filtration in the industry. TRONAIR® HPUs are available in different series and various configurations. Despite their differences all HPUs are powered by a motor (the primary source of power), which in turn powers the main pump to circulate hydraulic fluid from the reservoir throughout the entire system. Typically, motors are electrically powered. However, a few are gas and diesel-driven for outdoor usage. Other HPU components include the hydraulic pump which controls both the flow and the pressure within the unit, the reservoir (the storage area for the hydraulic fluid), the regulators which control or "regulate" the pressure lines and the relief and pressure supply lines which keep the pressure inside the hydraulic power unit level.

TRONAIR® Reservoir Service Units, under their Hydraulic Service Units product range, support control of contamination of hydraulic fluids from dirt, air, and water in aircraft hydraulic systems through the servicing process. Re-circulating the fluid, prior to servicing, removes particulate contamination from the servicing line and couplings through their 2 micron filter and air, visible in their transparent return hose. Pressure and vacuum valves in the reservoir fill cap minimize tank breathing and thereby control the entry of water into the fluid. TRONAIR® Reservoir Service Units feature a 2 gallon (7.6 liter) reservoir capacity and a maximum output pressure rating of 75 psi/5.2 bars or 200 psi/13.8 bars depending on the model. Units are shipped fully assembled with the exception of customer supplied quick-disconnect couplings. 

For more information please consult the supplied documentation. 

Note: TRONAIR® ATA-29 Hydraulic Power Service Units (HPUs) are offered with or without CE marking (*). Listed HPUs are non CE rated. For CE rated versions please specify during ordering. 

(*) CE marking indicates that a product has been assessed by the manufacturer and deemed to meet EU safety, health and environmental protection requirements. It is required for products manufactured anywhere in the world that are marketed in the EU.

SNAP-ON® high-end tools and equipment are intended for professional use in the transportation industry including the automotive, heavy duty, equipment, marine, aviation, and railroad industries. Marketed under many different brands SNAP-ON® product portfolio includes premium hand tools, power tools, tool storage products (including tool control software and hardware), diagnostics, equipment and related accessories, electronic parts catalogs, warranty analytics solutions, business management systems and services, OEM specialty tools and equipment development and distribution, and OEM facilitation services.

CDI TORQUE PRODUCTS® (a SNAP-ON® brand) relates to professional grade torque products manufactured and sold more than anyone in the world. CDI's mechanical torque product lines include click type torque wrenches, dial indicating torque wrenches, torque limiting screwdrivers, calibration equipment and a number of special application torque products. CDI has long been a major innovator and a leader in electronic torque measurement and torque calibration equipment.

TechWrench® and TechAngle® electronic torque wrenches revolutionized the industry with easy-to-use, push button precision tools. TechAngle® wrenches combine the ability of electronic torque and angle wrench to complete precise "torque plus turn" specifications.

Other torque wrench products and equipment include ControlTech® industrial wrenches, TQ Series adjustable click-type, Torqometer® wrenches and drivers, angle gauges, screwdrivers, geared head and torque multipliers, testers, electronic bench Top Torque testers and  calibrator as well as pneumatic and cordless torques.

For additional information on SNAP-ON® product lines please consult the supplied documentation.

JIFFY® AIR TOOL is a market leading solutions provider specializing in professional grade hand held, limited access, pneumatic drilling and fastener installation tools for the aerospace and aircraft industries. Manufactured in the USA, their product portfolio includes an extensive line of specialty hand-held pneumatic tools designed and built for easy, trouble-free operation and reach into difficult areas. Their tools are widely used by airframe assembly, maintenance, repair and overhaul facilities.

Modular Drill Motors & Attachments (JMD)

JIFFY® AIR TOOL pioneered the “Modular Tool” platform for drill motors and attachments (JMD). JIFFY® motors can accept a wide variety of drill attachments to meet limited access requirements.JIFFY® Pistol Grip Straight style drilling tools are offered in models with forward running, reverse running and reversible functions, safety trigger option, 250 – 20,000 RPM, and 0.3 – 1.5 HP.  Available Thread Sizes: 1/4-28, 10-32, 9/32-40, 5/16-24, 3/8-24 and 7mm Collet.

Modular Fastener Installation Tools (JMI)

With JIFFY® modular fastener installation platform installation motors can accept a wide variety of install attachments to meet limited access requirements. The latter are available in 17° indexable or fixed, 20° indexable or fixed, “L”, and straight install type offered in various series correlating to the torque capacity of the fastener. Their versatility is further enhanced by the three offered drive styles: a socket and key system,a flush gear with a key and a hex through with no key control to allow access to confined space installations.

In addition to the modular installation tools, ratchet install tools in straight, 17° and 20° head styles are also available. Their pneumatic ratchet wrenches can be used for HI-SHEAR fastener (*) installation quickly, easily, and efficiently. Their new & improved spring loaded hex tip holder allows the use of special hex tips that will hold the HI-LOK™ style fastener in place when installing non-interference fasteners. With the new & improved design, hex tips are easier than ever to change and can literally be changed in just a few seconds.JIFFY®  sockets and hex tips (sold separately) can be used with these wrenches.

For additional information please refer to the supplied documentation or contact us.

 (*) HI-SHEAR CORPORATION Fastening System includes HI-LITE™, HI-LOK™ and HI-LOK™/HI-TIGUE™ pin and collar fastener combinations. The HI-LOK™ fasteners are the second most used fasteners in aircraft structural assembly after the solid rivets MS20470 and MS20426. The HI-LOK™ fastener system includes a rivet pin (similar to a screw but with additional advantages) and a collar (similar to a nut). Pneumatic installation/removal tools for HI-LOK™ or HI-LOK™ style fasteners are also offered by  HS Tooling and U.S Air Tool Co. (USATCO). Please refer to the respective product presentations.

The landing gears and doors used in commercial airplanes are moved by a set of actuating cylinders. For each door, a cylinder opens and closes the door. Landing gear door locks offered as  part of our own label  AVIATIONEU NEW ERA product portfolio of Aircraft MRO Equipment are high strength steel clamping tools which retain the door actuator in closed position. They fit around the actuator and secure two tension rods to the door Iinkage. For more information and a quotation please contact us.

Gauges (also termed as gages) and gauge scales are widely used for inspection or measurement of correct grip length of  rivet pins, shear lockbolts, structural screws and bolts in aerospave and industrial applications. They ensure correct fastener selection, enhancing structural integrity, simplify the measurement process saving time during assembly, and improve accuracy in maintenance and repair tasks. Made from durable materials for long-lasting use (including high-strength alloys and stainless steel) they come with easy-to-read markings for quick and precise measurement.

Protrusion grip gauges & their assemblies (including apart from the grip gauge a grip gauge slide) can be supplied for use on HI-SHEAR Hi-Lilte®/Hi-Lok®/Hi-Tigue® Series of fasteners or those from PCC CHERRY AEROSPACE. 

These gauges are offered as sets of blades with different color markings for different nominal diameter sizes in Inch or Metric (mm) systems with the letter "M"in their part number denoting a Metric version. For example, those with 2-1522 part number, include five stainless steel blades (5/32", 3/16", 1/4", 5/16", and 3/8") on a keychain for portability, and can be used  with HI-SHEAR Hi-Lok®/ Hi-Tigue® fasteners ensuring proper pin protrusion for safe aviation fastener applications.Their counterparts, 2-1522HST are suitable for HI-SHEAR Hi-Lilte® fasteners. 

Grip Gauge Scales with or without a slide are also offered with measurement graduations in inches or inches and millimeters. The 269C3 Grip Gauge Scale from PCC CHERRY AEROSPACE, made of high-strength alloy, has been designed for precise grip measurement in various materials in aircraft structures. Can be used with CherryMax® & CherryLok® rivets. Its durable construction ensures long-lasting use, while its clear markings for quick reference, and user-friendly design for easy insertion into prepared holes for reliable readings, simplify the measurement process.

Depending on the selected part & stock conditions, grip gauges & scales for HI-SHEAR and PCC CHERRY AEROSPACE fasteners can be supplied as OEM parts or equivalent parts from other suppliers, such as OMEGA TECHNOLOGIES (separately listed) meeting or exceeding specifications. 

Economy models of gauges for shop rivet heads and rivet lengths are also available from ATS and AVERY TOOLS and can be used for measuring both universal head and flush rivets. Rivet head gauges are offered as a set of four gauges for -3, -4, -5, & -6 rivet sizes permanently stamped on each gauge. Each gauge measures MINIMUM height and MINIMUM diameter of shop heads AFTER setting eliminating guessing if the rivets are properly set, and are color coded with anodized finish. Their respective rivet length gauges measure -3, -4, -5 & -6 rivets and have been designed for checking the length of rivets BEFORE setting. Their set of rivet head gauges and the length gauges can be ordered as kits or separately.

For more information please contact us.

HSTOOLING (formerly HI-SHEAR TOOLING) is a brand of ZEPHYR Manufacturing Co., Inc. (aka Zephyr Tool Group) designing and manufacturing the highest quality aerospace and industrial assembly tools and tooling systems.

HSTOOLING product porfolio includes installation, assembly and repair tools for Aerospace (air drills, riveters, both conventional rivet hammers and compression riveters, specialty fastener installation and other tools and accessories).

HSTOOLING ULTRALITE® compression riveters include different models covering different capacity requirements for aluminum and steel.They are  offered in Alligator jaw and C-Yoke models and feature ergonomic design, weight reduction vs. comparable-force models, high-strength forged jaws and C-yokes, precison bearings and shafts.  The new 702 and 702T alligator models posess outstanding force-to-size ratios. 

HSTOOLING Air Driver Assemblies are designed specifically for installing HI-SHEAR CORPORATION HI-LOK™ (*), HI-LITE™,  and HI-LOK™/HI-TIGUE™ pin and collar fastener combinations. They come in a variety of sizes and configurations, to drive fasteners in both open and restricted-access areas. Compact, lightweight, fast and reliable HSTOOLING tooling systems generate low noise compared with conventional riveting, require minimum employee training, and are designed to operate at a normal factory air pressure of 90 psi with 1/4 or 3/8 inch air lines.

Installation/removal tools for Hi-Lok™ or Hi-Lok™ style fasteners made by Jiffy Air Tool and USATCO are also offered. Pleae refer to the respective product presentations.

For additional information please refer to the supplied documentation or contact us.

(*) The HI-LOK™ fasteners from HI-SHEAR CORPORATION, subsidiary of LISI AEROSPACE, are the second most used fasteners in aircraft structural assembly after the solid rivets MS20470 and MS20426. The HI-LOK™ fastener system includes a rivet pin (similar to a screw but with additional advantages) and a collar (similar to a nut).

PAN AMERICAN TOOL CORPORATION manufactures and supplies specialized precision metal cutting tools for private, business, commercial aviation and military applications. Their NOVA® Pneumatic Tools is a complete line of high-quality, competitively priced aerospace pneumatic drills and aircraft tools. 

NOVA® Pistol Grip Drills are available in a variety of speeds and torques  as well as chuck sizes and designs. Intended for use in general drilling, reaming and screw removal applications. Engineered for use with a combination of PAN AMERICAN's threaded shank adapter drills, insert bits, and composite cutting tools for many drilling applications.

NOVA®  STANDARD and COMPACT Series pneumatic drills are engineered and built for close quarter drilling in aviation, aerospace, automotive, and shipbuilding applications. Their ergonomic design reduces operator stress and muscle fatigue. Drills in both series feature a rear exhaust with bronze muffler, hardened alloy-steel planetary gears and heavy duty motor cylinder and rotor. Their grease fittings in the motor housing and head provide for easy lubrication and smooth, quiet operation. In STANDARD Series the motor to head assembly adapter is built onto the motor housing, making for a self-contained unit, minimizing gear separation for increased tool durability and longevity. In the COMPACT Series the motor to head adapter is built onto the heads, shortening the overall length of the tool allowing drilling in even the tightest of areas. The NOVA®  STANDARD system offers 5 straight motor housings, providing a variety of speed and torque options with 19 interchangeable heads, allowing for drilling in even the most difficult to access areas.The COMPACT Series includes 4 motor housings as well as 6 interchangeable heads. NOVA®  STANDARD drills and their COMPACT counterparts are designed to be used in combination with PAN AMERICAN TOOL's threaded shank adapter drills. The COMPACT system  offers Nova Standard pneumatic tool heads that can be adapted to compact motor housings with optional adapter system, offering more possibilities for the drilling needs.

Apart from individual units NOVA®  STANDARD and COMPACT Tool Kits are also offered with customer selection from the motor housings and heads included in the respective series for current and future drilling needs. Each kits features: 

- heavy duty carrying case.

- cut outs designed to hold Nova Pneumatic Aircraft Tools.

- choic from one of 3 motor housings and 10 Heads in STANDARD System or from one of 4 motor housings and 3 or 6 heads in the COMPACT system.

- one year warranty.

For additional information please consult the supplied documentation.

AVIATIONEU NEW ERA frames for storage of aircraft engine pylons are offered as part of our own label product portfolio of Aircraft MRO Equipment and they are indispensable equipment for any Maintenance, Repair and Overhaul (MRO) facility. 

Different pylon storage frames are offered corresponding to diffent aircraft engines. The PN: 460007240 98A54003003000 frame is intended for use to handle and store pylons of GENERAL ELECTRIC (GE) and PRATT & WHITTNEY (PW) aircraft engines.  For more information and a quotation please contact us.

An aircraft elevator removal installation sling is the supporting frame which, together with the car platform, guide shoes, elevator car safety, hoisting ropes (or sheaves) and/or associated equipment, are used to as to remove or install the elevator from an aircraft. AVIATIONEU NEW ERA slings are offered as part of our own label product portfolio of Aircraft MRO Equipment. The PN: -C55001-1 elevator sling is intended for use on BOEING  737-300 thru -500 and 737-200 series airplanes with composite elevators. For more information and a quotation please contact us.

AVIATIONEU NEW ERA aircraft wheel axle jack falls under our product lines of Aircraft MRO Equipment. It is mainly used for tire change in aircraft. It includes a pneumatic hydraulic mode and features a lift weight capability of 50T for use in commercial aircraft like A320 and B737. The cylinder block is made of high-quality manganese steel and the surface from high-quality carbon steel, chromium plated, galvanized and plastic sprayed. The minimum height of the hydraulic cylinder is 245mm and the maximum height is 565mm. With a robust construction ensuring a long service life, versitile use and competitive price, AVIATIONEU NEW ERA aircraft wheel axle jack is an indispensable equipment for any Maintenance, Repair and Overhaul (MRO) facility. For more information and a quotation please contact us.

The new 3882 series Cylinder Base Nut wrenches by AIRCRAFT TOOL SUPPLY COMPANY (ATS) are made from forged alloy steel, tempered, and hardened for maximum strength. They also have an industrial chrome plating to improve surface wear, and protect against rust and corrosion. Their thin-wall construction guarantees they will fit nuts close to the cylinder casing without grinding down the wrench's outer diameter. And with a 15" span, they clear even the tallest cylinders. The new 3882 cylinder base wrenches replacing ATS 2882 series address just about every concern of the previous 2882 series, while including several enhancements for work easier while carrying the ATS Pro lifetime warranty. The set includes 4 wrenches in Hex Sizes: 1/2", 9/16", 5/8", and 3/4" suitable for all Continental, most Lycoming, and many other types of aircraft engines.

AVRO TOOLS manufactures countersinking and pneumatic tools including high performance pneumatic rivet hammers, drills, precision microstops and tungsten bucking bars.

For over 60 years, CHERRY® AEROSPACE Installation Tools have been specified and used by aircraft manufacturers and repair facilities throughout the world. Each CHERRY® AEROSPACE fastening system is combined with a full range of tools to provide an overall systems approach that ensures optimum compatibility and consistent installation performance. Used worldwide, Their tools are are manufactured to provide maximum service with minimum care. They are offered in a wide variety of hand, pneumatic and pneumatic/hydraulic versions, with optional accessories to permit their use in difficult and limited access areas. The size and type of fastener being installed dictates the type of tool to be used. All installation tools are manufactured at CHERRY® AEROSPACE's plant in Santa Ana, CA, USA.and they are CE Certified.

For additional information please refer to the supplied documentation or contact us.

APEX® TOOL GROUP (ATG) is one of the largest manufacturers of professional hand and power tools in the world, serving the industrial, vehicle service and assembly, aerospace, electronics, construction and DIY markets. ATG products are offered through vatious brands.

ATG’s three main product types include:

Hand Tools: mechanic, trade, and specialty tools, chain, truck boxes, jobsite storage and drill chucks for a broad range of industrial, construction, vehicle repair and DIY applications.

Power Tools: electric, pneumatic and air tools, as well as high performance bits, torque measurement, metal cutting and drilling solutions to the global industrial, vehicle assembly, aerospace and utilities/energy markets. CLECO®, one of ATG brands,  is one of the  pneumatic fastening brands to meet and exceed aerospace and motor vehicle assembly requirements. CLECO® product portfolio  includes the following assembly tools, material removal, drilling and riveting tools. CLECO DOCTO™ brand offers a premier line of material removal tools in the industrial marketplace. 

ASSEMBLY TOOLS: nutrunners & screwdrivers, fixtured spindles, controllers & software, impact wrenches, pulse tools, torque wrenches, air motors and accessories,

MATERIAL REMOVAL TOOLS: grinders, sanders & polishers, specialty tools and accessories,

DRILLING & RIVETING TOOLS" hand drilling, countersinking & spotfacing, riveting and accessories.

Electronic Tools: precision soldering, cutting, motion control and air ventilation solutions to electronics assembly industries.

For additional infomation on ATG tools please consult the supplied documentation.

Aircraft waste leak testing equipment are used to plug the waste system and provide leak detection. AVIATIONEU NEW ERA aircraft waste leak testing equipment are offered as  part of our own label product portfolio of Aircraft MRO Equipment. For more information and a quotation please contact us.

U.S. Air Tool Company Inc. (USATCO) is a manufacturer and worldwide distributor of high quality tools for the aerospace/aviation industry. Their offered product range includes installation, assembly, and repair tools and related accessories for air drilling,punch & cutting,  clamp & fastening, cable, wiring & tubing,  lighting & inspection, testing & measuring, riveting, sheet metal forming, sanders & grinders, files,  abrasives & saws, an extensive range of hand, assembly, shop & application tools and more.

For additional information onUSATCO product portfolio please refer to the Product Description section, the supplied documentation or contact us.

ERNEST H HILL LIMITED (HILL PUMPS) is a manufacturer of fluid transfer equipment for automotive and industrial lubrication, petrochemical, industrial, agricultural and aerospace fluid transfer applications.

HILL supplies a comprehensive range of pumps, lubrication, garage & workshop equipment to all types of industries, from aviation & agricultural pumps to industrial and automotive servicing equipment.

HILL pumps are designed for use with chemicals, oils, AdBlue/UREA, water, diesel, antifreeze, grease, gear oil. Their food grade approved pumps are intended for use within the food and drink sector. Apart from pumps HILL supplies  an extensive range of garage equipment such as hose reels and waste oil drainers. 

For additional information on HILL PUMPS products please consult the supplied documentation or contact us.

Miscellaneous OEM special tooling / equipment used for the maintenance & repair of aircraft piston and turbine engines. Used by airline companies  and Aircraft Maintenance, Repair and Overhaul facilities (MROs) in various applications. Available in NEW or USED conditions.  For additional information please consult the supplied documentation or contact us for non listed tools.