Genuine DEUTZ filters provide the highest quality, best filtration performance and long service life leading to optimum protection, consistent performance and low fuel consumption of the engine. DEUTZ Air filters provide reliable filtration of combustion air, preventing dust from entering and causing increased wear inside a combustion engine. DEUTZ Oil filters preserve the engine performance and reliability protecting it from wearing and damage caused by dust, soot and other particles. DEUTZ Fuel filters provide highly efficient separation of harmful particles and water ensuring high fuel quality and engine protection from compromised engine´s performance and shortening of its life cycle.

Aircraft hydraulic pumps are used to move non-compressible fluid through an aircraft hydraulic system. This power is often used on small airplanes to operate wheel brakes, retractable landing gear, and some constant-speed propellers. On larger airplanes, hydraulics are used for flight control surfaces, wing flaps, spoilers, and other systems. Aircraft hydraulic pumps are normally engine driven, but sometimes to simplify the system manufacturers use an electric motor to drive the hydraulic system. These hydraulic power packs incorporate a reservoir, control valve and auxiliary valves into a single unit.

As the OEM for the PRESTOLITE Power Packs, AEROSPACE TURBINE ROTABLES Inc.applies an extensive overhaul and testing process to ensure a long and reliable operation of PRESTOLITE Hydraulic Power Packs offered as Overhaul/Exchange (*).  

(*)requires the return of the old unit and its exchange by an overhauled one. The supplier maintains the right to check the condition of the returned unit before the exchange. The price also applies to the hydraulic power packs shipped for overhaul of the same unit and return. 

When intended for use on certified aircraft applications, PRESTOLITE Overhaul/Exchange Hydraulic Power Packs come with Dual Release (FAA/EASA) Certification . It must specified at the time of ordering as additional charges may apply.

For additional information please consult the supplied documentation.

Manufactured to the highest standards, the Andair standard fuel selector range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. Duplex fuel selectors are also offered by Andair (see separate product presentations). FS16, FS20 and FS25 series of fuel selectors are designed for safety, provide a precise and smooth feel in operation  and come in different types, ranging from Type 1 ON/OFF shut off valves to valves with multiple positions to ensure the right fuel tank selection. Can be supplied with different fittings. To prevent the pilot switching the wrong tank or turning the fuel off they feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off.

Designed for use with Light Sport and Ultralight aircraft, FS16 series 1/4" fuel selectors come in the following types:

Type 1 (FS16x1): simple 1/4” ON/OFF shut off valve with 90 degrees action between the two positions. On the FS16x1 there are two ports and either port can be used as the inlet or outlet.

Type 2 (FS16x2): Three way 1/4” fuel selector with positions LEFT-RIGHT-OFF and a 90 degree action between each tank selection. No lower fitting for use where there is little space behind the valve. 

Type 4 (FS16x4): Designed for high wing aircraft, it has four lever positions OFF - LEFT - BOTH – RIGHT with a 90 degree action between each position.On the FS16x4 there are 3 ports. The lower port is the outlet to the engine is 1/8 NPT Female. The inlet, side ports are 1/8 NPT Female and are at the 9 o'clock and 12 o'clock positions when looking at the valve with the brass ball spindle pointing upwards. At the 3 o'clock position there is a blanking plate that covers up a PTFE gland opposing the forces of the other 2 PTFE glands.

Type 2 and Type 4 valves do not allow cross feed between each tank when the selector is in the OFF position.

For additional information please refer to the product presentations, the supplied documentation or contact us.

Honeywell is a leading switch and sensor provider for many HVAC applications, including airflow, VAV control, boiler/chillers, motors, and more.  Products include pressure sensors, digital humidity/temperature sensors, magnetic position sensor ICs, current sensors, pressure switches, basic switches, and more.

Honeywell's MICRO SWITCH switches fill many roles in a wide range of applications, including presence/absence/positioning, inspection/recognition, condition measurement, and operator/machine interface. They range from sealed switches used in high temperature aerospace applications to large cable-pull switches ensuring safety on conveyors.

Honeywell's snap-action basic switches are simple, superior, durable, and irreplaceable. Globally compliant and known worldwide for their compact and lightweight design, MICRO SWITCH snap-action switches are designed for accurate repeatability and extended life. MICRO SWITCH Basic switches are designed for presence and absence detection where physical contact with an object is permissible. They also excel in applications requiring simple on-and-off actions. 

Honeywell's  Standard families of Basic and Miniature switches include V15 series, and are designed with the same high quality standards, but for low cost-of-failure applications — ones where the cost of replacing the switch is less than the total cost of a switch failing.

The Premium families of MICRO SWITCH Large and Subminiature switches are designed for high-precision applications where the cost of a switch failing is high maintaining enhanced accuracy and repeatability. MICRO SWITCH premium basic switches are offered in different series, they feature precise and accurate characteristics. Available in large, miniature, and subminiature switch sizes, MICRO SWITCH premium basics are customizable to provide unique actuators, different terminal combinations, custom characteristics, and even value-added wires… to meet customers’ application requirements. With many Honeywell premium basics, they are tested and certified to a higher cycle count.

FALLS FILTRATION TECHNOLOGIES Inc. (FFT), formerly AIRMAZE Inc., manufactures a wide variety of highest quality plastic and metal air intake systems and their filter element replacements as well as filtration equipment (such as oil, air/oil separation and hydraulic filters) for the industrial, agricultural, and aerospace industries.

Today FFT filtering products are  typically initially installed or used as retrofits on aircraft, agricultural, railroad, construction, trucking and power industries for a wide range of applications including gas and diesel engine filtration, filters for generators and gas compressors, light, commercial, and military aircraft filters, vacuum pump filters, pressure blowers, and filters for locomotives.

FFT AIRMAZE designed product lines include UNIMAZE small filters, MULTIMAZE industrial air intake filters, breathers, air intake panels, oil bath filters, AUTOMAZE self cleaning air filters, and MUFFLEMAZE noise reducers.

FFT AIRMAZE aircraft & military product lines include strainers used from fuel to lube oil, wash flow filters used primarily in throttle control systems, FAA PMA fuel filters, in-line filters and replaceable filter elements. FFT AIRMAZE AM01W052261 fuel filter assembly is a FAA PMA fuel filter approved for installation in  the Lake Model LA-4-200 airplane, replacing older Bendix 450-OK fuel filter.

For additional information on FALLS FILTRATION TECHNOLOGIES product portfolio please refer to the Product Description section and the supplied documentation. Filter element replacements for FFT filters are offered both as OEM parts or equivalent to / interchangeable with FFT parts from other manufacturers. Please refer to our respective product listings.

The DUKES AEROSPACE Inc. is a manufacturer of  fuel pumps for general aviation and corporate aircraft.  DUKES fuel pumps are used in a range of aircraft such as Beechcraft, Cessna, Diamond, Maule, Mooney, Lake and Navion aircraft. The company is a subsidiary of AERO FLUID PPRODUCTS, part of TransDigm Group Inc.

The DUKES AEROSPACE fuel pumps are offered as NEW, OVERHAULED or OVERHAULED EXCHAGE (in the second case, in exchange of existing customer owned unit (core) for a quick turn around). Overhaul pumps are serviced in accordance with FAA-approved process specification and certified (FAA Form 8130-3) by authorized repair stations such as QUALITY AIRCRAFT ACCESSORIES, the exclusive DUKES AEROSPACE  authorized overhaul facility for General Aviation fuel pumps,  RAPCO FLEET SUPPORT SERVICES division or CJ AVIATION. In the case of exchanged pumps,  the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders with us when our co-operating supplier verifies that the unit is in a serviceable condition. 

Additionally, FAA-PMA approved direct replacement fuel pumps to the respective DUKES AEROSPACE  models are offered. They are made by reputable manufacturers such as CJ AVIATION and offered as NEW or NEW EXCHANGE (please refer to their separate product presentations). For additional information please consult the supplied documentation of our offered products (*) or contact us.

(*) The supplied documentation is to be used for reference only. When selecting a part for installation, consult the appropriate aircraft maintenace manual, parts catalogue, or equipment list for approved data.

LENZ Model DB desiccant breather filters fall under the company's extensive product portfolio of tank accessories. Made from ABS plastic & impact-modified acrylic LENZ tank breather filters remove corrosive water vapor and they are offered in four standard sizes (3" to 10"). Additional characteristics and features include:

• Operating temp. range: -20˚ F to +200˚ F (-28˚ C to +93˚ C)

• Bi-directional air flow

• Silica gel turns from gold to green when maximum absorption is reached

• Dual filter system with anti-static guard

• Solid contaminant filtration surface area 20.6 in2 (133 cm2)

• Silica gel absorbs up to 40% of its weight in water

• Resistant to alkalis, hydrocarbons, non-oxidizing acids, salt water,and synthetic oils

Available options include:

• Activated charcoal media (consult factory)

• 5 PSI Maximum Operating Pressure

For additional information please refer to the supplied documentation.

Tempest® Spin EZ® FAA PMA approved aviation oil filters are manufactured by Aero Accessories®, LLC. Apart Spin-EZ® gasket oil filters the company also manufactures other pneumatic products such as Tornado™ dry air pump.

Product Features:

Improved Nut Welds – Nut welds are so strong that the can will distort without breaking the welds.Tempest Original filters can be installed without the danger of installation nuts falling off.

Improved By-Pass Valve for Continental® Engines – Meets TCM by-pass specification of 12-14 psi, reducing risk of premature bypass that can result in unfiltered oil flowing to your engine.

PC Housing (Patent Pending) – the only filter to incorporate a housing for the by-pass valve to prevent the restriction of the oil outlet should a failure of the by-pass valve occur.

Burst strength of 600 psi – Significant improvements to the roll seam process used on the bottom of the can substantially improved the design burst strength of the Tempest Spin EZ oil filter to over 600 pounds per square inch, exceeding the ARP 1400 standard by 50 percent. Extra strength gives added assurance that Tempest oil filters are made to withstand the harshest operating conditions.

Full Pleat Media – The resin-impregnated, cellulosic, full pleat media is designed for uniform flow and collapse resistance.  312 square inches is the most in aviation oil filters.

Tempest® Spin EZ® oil filters are sold individualy but also offered as economical, convenient, and easy to handle six and twelve packs. Spin EZ® Solid Lubricant, aTempest Spin EZ oil filter’s proprietary solid lubricant is also available allowing for easy removal of the filter. Unlike oil, grease or DC4 compound that leave the filter seemingly “bonded” to the engines mount pad, making it nearly impossible to remove, Tempest® Spin EZ solid lubricant won't extrude or squirt out from under the seal.

PLease consult the supplied documentation for additional information.

Series 580 and 593 NPT swing check valves by PARKER Hydraulic Valve Division permit free flow in one direction, and shut off in the reverse direction with an extremely low internal leakage. Series 580 and 593 check valves will provide low pressure drop.

Body and cap are made from aluminum alloy, anodized. Internal parts are from aluminum alloy, anodized and stainless steel. They feature synthetic rubber molded seal and o-ring.

They come in different sizes: NPT 1/4", 3/8",1/2",3/4",1",1-1/4",1-1/2".

Product Features:

• Light weight aluminum

• NPT female fitting (NPTF)

• Zero leakage (less than 1 drop per minute)

• Full flow with low opening pressure

• Improved hinge controls

• Mounts in any position

• MS valves meet the following specifications: MS28882A or B, MS28884A or B

FLEETGUARD® filtration product portfolio by ATMUS FILTRATION TECHNOLOGIES includes a wide range of cleaning products for all media, as well as chemical compounds and additives for cooling systems.  With more than 6.000 offered products, including air, oil & fuel filters, fuel /water separators, coolant filters/additives, and hydraulic filters, FLEETGUARD® is the worlds leading filter maker with their products used by a wide range of engine and other manufacturers for buses, trucks, generators, construction machines, marine and agriculture applications. Genuine FLEETGUARD® filters are offered along with their respective replacement parts manufactured to OEM specifications from third manufacturers. For more information please contact us.

The PARKER AIRBORNE designs and manufactures motor driven fuel fuel  boost and transfer pumps and is part of the PARKER AEROSPACE GROUP of the PARKER HANNIFIN CORPORATION. These pumps consist standard equipment by the world's leading airframe manufacturers. The PARKER AIRBORNE product range includes:

- In Line fuel pumps for low-flow fuel applications,

- Submerged Centrifugal fuel pumps,

- High Performance Centrifugal fuel pumps for use in turboprop or turbofan jet aircraft,

- Submerged Duplex fuel pumps with two distinct pumping elements

The PARKER AIRBORNE fuel boost pumps use 28 V direct current (DC) to drive a highly efficiency, brushless DC (BLDC) motor or 115.5 V alternating current (AC) three-phase induction motors. The BLDCmotor-driven pumps incorporate integral electronic controllers using Hall Effect sensor rotor-position feedback. The hardware-only controller doe not use any software or programmable logic devices. These pumps feature:

-fuel cooled motor and electronics

-fuel wetted carbon bearings allowing for long-life fluid film design with no rotating shaft seals

-a high efficiency brushless DC (BLDC) motor or a three-phase induction motor

-qualification for high levels of lighting and electromagnetic interference (EMI).

The PARKER AIRBORNE fuel boost pumps can be furnished as either NEW, NEW EXCHANGE or OVERHAUL EXCHANGE. 

Offered pumps in OVERHAUL Condition are supplied in accordance with FAA-approved process specification, come with a FAA Form 8130-3 and can be provided in exchange of existing customer owned units (cores). In all EXCHANGE cases,  the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders with us when our co-operating supplier verifies that the unit is in a reasonable condition. For additional information please consult the supplied documentation (*) or contact us.

In addition to the PARKER AIRBORNE pumps, RAPCO FAA-PMA approved pumps are also offered as direct replacements  to the respective PARKER AIRBORNE models. The RAPCO replacement pumps can be furnished as either NEW EXCHANGE or OVERHAUL EXCHANGE (please refer to their separate product presentation).

(*) The supplied documentation is to be used for reference only. When selecting a part for installation consult the appropriate aircraft maintenance manual, parts catalogue, or equipment list for approved data.

DONALDSON® is a leading world-wide filter supplier for commercial jets, military vehicles, off-road equipment, trucks, light-duty vehicles, power plants, dust collectors, industrial compressors and more. The company is the OEM for  FAA-PMA air filters installed in Cessna (all SE piston models), Piper (turbo charged aircraft), Beechcraft,  Maule & Mooney aircraft delivering consistent and reliable performance.

Product Features:

Selection: Over 75 filter models for Cessna, Beech, Maule, Mooney, Piper and other aircraft.

Easy Installation & Maintenance: No removable parts or oil, may be washed with water.

Better Airflow:  In laboratory airflow tests comparing DONALDSON®, Bracket and Challenger Aviation (K&N) filters for Cessna 172 aircraft, DONALDSON® had the lowest restriction (best airflow). The reasons for this include:

• Filter media is composed of synthetic fibers

• Evenly distributed uniform size and shape media fibers

• More media area and less frame

• Deeper filter pleats

• No oil

Stop more dirt and protect the engine better: They achieve 98.5% or greater filtration efficiency according to ISO5011 fine and coarse dust requirements, greatly exceeding the other filters. 

Long Lasting: rated to last 500 hours, five to 10 times longer than foam filters. Replacement after three years, five cleanings or 500 flight hours, whichever occurs first.

OEM and FAA-PMA Certified: Designed to manufacturer specifications, DONALDSON® filters don not require STCs .

Thoroughly Tested: Third party lab tests show Donaldson filters meet or exceed FAA fire safety regulation per FAR 25.853 and FAR 23.1107 Induction system filters.

Please refer to the attached documentation on the application of DONALDSON® filters in different aircraft/models.

FACET® and PUROLATOR® are both brands of MOTOR COMPONENTS, LLC. a manufacturer of electronic fuel pumps  and filtration products. The company is a global leader in the electronic fuel pump industry. FACET® and PUROLATOR® products are known for their high quality and dependability. 

Starting with fuel filters, FACET® and PUROLATOR® filter range has expanded to include oil filters, hydraulic fluid filters, air filters and water filters to their lineup.  FACET® and PUROLATOR® fuel and other aircraft filters have a pleated design to maximize the filtration surface for faster, more efficient filtration. They carry a  FAA-PMA approval and can be used in a variety of aircraft applications providing reliable, long-lasting and proven to work filtration solutions. Sold in pieces or packs of 10 pieces each. They come with Certificate of Conformance as standard. If additional certification is needed, manufacturer's certification and a FAA Export 8130-3 form can be provided with any qualifying filter item at extral cost.  In this case please select listed products with the extension "CERT" in the product reference code (SKU) from our offered items.

LEAR ROMEC is a brand of CRANE AEROSPACE & ELECTRONICS for fluid management solutions in aircraft, gas turbine engines and radar cooling systems. The LEAR ROMEC products are suitable for applications in the commercial transport, general aviation, business, regional jet and ground based gas turbine markets.

CRANE AEROSPACE & ELECTRONICS is a world leader in the design and manufacture of high performance, technology, accuracy, and reliability positive displacement pumps, centrifugal pumps and true mass flowmeters, under the company's ELDEC, HYDRO-AIRE and LEAR ROMEC brands, which are used in aerospace and defense applications.

Product lines include:

- Vane type positive displacement lube & scavenge pumps featuring high reliability and volumetric/mechanical efficiency, excellent flow performance at high altitude/low inlet pressures, excellent priming performance, lowest weight option for high flow pumps (such as Geared Turbofan) and high contamination wear resistance,

- Fuel Flow Transmitters (FFT) for aircraft engines featuring a +/-0.5% accuracy performance of flow point in the engine cruise range, form factor and flow conditioning for difficult installations,

- Centrifugal pumps for fuel, water and coolant applications of different drive types including gearbox driven, hydraulic motor driven, 400 Hz fixed frequency AC, 28 VDC brush and brushless, and 270 VDC brushless. Like the lube & scavenge pumps, these pumps are characterised by high reliability and volumetric/mechanical efficiency, priming performance and contamination wear resistance.

LEAR ROMEC customer owned fuel pumps can be overhauled or offered in overhaul/exchange condition for immediate shipment. In case of no core returns, core charges apply. Please see below an indicative list of available LEAR ROMEC fuel pumps for overhaul/ exchange or contact us for additional information.

LEAR ROMEC Part Numbers: 

RG15980 | RG15980P 

RG17980 | RG17980A | RG17980A/M | RG17980/M | RG17980D | RG17980D/M | RG17980E | RG17980E/M | RG17980J | RG17980J/M | RG17980K | RG17980K/M | RG17980P | RG17980P/M | RG17980U | RG17980U/M

RG9080F1 | RG9080F1/M | RG9080F2 | RG9080F2/M | RG9080G1 | RG9080G1/M | RG9080G2 | RG9080G2/M| RG9080H1 | RG9080H1/M | RG9080H2/M | RG9080J1 | RG9080J1/M | RG9080J4A | RG9080J4A/M | RG9080J6A | RG9080J6A/M | RG9080J7A | RG9080J7A/M | RG9080J8A | RG9080J8A/M

RG9570K1 | RG9570K1/M | RG9570K2 | RG9570K2/M | RG9570K3 | RG9570K3/M | RG9570K4 | RG9570K4/M | RG9570P1 | RG9570P1/M

Manufactured to the highest standards, the Andair standard fuel selector range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. Duplex fuel selectors are also offered  (see separate product presentations). FS16, FS20 and FS25 series of fuel selectors are designed for safety, provide a precise and smooth feel in operation  and come in different types, ranging from Type 1 ON/OFF shut off valves to valves with multiple positions. To prevent the pilot switching the wrong tank or turning the fuel off they feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off.

FS20 series 3/8" fuel selectors provide a choice of lower and side fittings, and all units can be operated with an extension and universal joints. They come in the following types:

Type 1 (FS20-1): simple 3/8” ON/OFF shut off valve with 90 degrees action between the two positions. There are two ports and either port can be used as the inlet or outlet.

Type 2 (FS20-2): Three way 3/8” fuel selector with positions LEFT-RIGHT-OFF and a 90 degree action between each tank selection. No lower fitting for use where there is little space behind the valve. 

Type 3 (FS20-3): three way selector with the positions LEFT - RIGHT - OFF. Generally used in low wing aircraft with a tank in each wing.

Type 4 (FS20-4): Designed for high wing aircraft, it has four lever positions OFF - LEFT - BOTH – RIGHT with a 90 degree action between each position.There are 3 ports. The lower port is the outlet to the engine and can be Male AN-6, Female 1/4NPT or a  360 degree Banjo adjustable fitting with a male AN-6 end.

Type 5 (FS20-5): 4 way Fuel Selector ( 3 tanks and OFF ) with positions LEFT - MAIN - RIGHT - OFF, each at 90 degree intervals.

Type 7 (FS20-7): Newest in the range 3 way fuel selector with positions LEFT - RIGHT - OFF. The inlets are at the 45 degree positions, to the LEFT and RIGHT, and the outlet is at the base of the valve. FS20-7 has been designed for centre consol mounting.

Type 8 (FS20-8): 5 way Fuel Selector ( 4 tanks and OFF ) with positions LEFT TIP - LEFT - RIGHT - RIGHT TIP - OFF, each at 72 degree intervals. 

For additional information please refer to the product presentations, the supplied documentation or contact us.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different vacuum pumps are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. The RAPCO FAA/PMA'd vacuum pump, RA215CC  is used in ROTAX® 912 UL, 912 ULS and 914 UL engines. Please refer to the separate product presentation for RAPCO Dry Air Pumps for vacuum or pressure system applications.

Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

CONCENTRIC HE Series AC/DC power packs allows the selection from a broad range of standard components to design a power system to meet the exact specifications of applications, both vertical and horizontal, with a full range of valving, motor, pump and reservoir combinations and minimum inventory for maximum cost efficiency. Other advantages of the HE power packs includes low power consumption, quiet operation, proven field performance and long service life. Concentric HE2000 Series AC/DC Power HPUs  can be coupled via suitable hydraulic lines to a wide range of operating mechanisms. They normally operate hydraulic cylinders, but can be used with any other hydraulic actuating device. A unit can individually control up to four (4) hydraulic cylinders.

Product Features:

All units have:

12 or 24 VDC motors

Adjustable internal relief valve preset at factory

Load holding check valve

Reservoirs plumbed for horizontal / vertical mount

Various size cylindrical/rectangular reservoirs

9/16˝-18 SAE outlet and return ports (P/N 1303835 1/4˝-18 NPTF ports)

140 x 170 mesh inlet strainer

Please refer to the attached documentation for specifications & additional information.

Sourced from quality producers, AVIATIONEU NEW ERA general purpose brass check valves with nylon cover are suitable for use in hydraulic, heating, air conditioning and pneumatic installations in vertical, horizontal or oblique positions. They are manufactured in accordance with ISO 228 standard and they are available in different sizes. Sold in pieces.

MANN+HUMMEL GmbH is a manufacturer of high-performance, precision-engineered filtration products offered under their globally recognized MANN-FILTER® brand. The MANN-FILTER®  product portfolio includes 6,800 superior original equipment quality filters and automotive aftermarket filters protecting engines, passengers and machines and used in over 300,000 applications.

MANN+HUMMEL PUROLATOR® brand relates to a compehensive range of engine air and oil filters, power steering filters, fuel/water separator filters and cabin air filters. Includes a growing line of heavy-duty filtration products for medium- and heavy-duty applications and can be used on various trucks such as Freightliner, International, Mack, Volvo, Peterbilt, Sterling and Kenworth, Bomag and Atlas Copco compressors, Deutz and Fendt tractors and others.