Fine quality switch from ACS used in many aircraft. The switch housing is machined from billet aluminum which makes this switch 25% lighter. It provides “ON” and “OFF” electrical control of both magnetos on a single engine aircraft. The key-operated switch mounts from the rear of the panel in a 7/8” dia hole. Available with or without starter position. A-510-2 model with starter position is supplied with switch plate two keys. (diode included). FAA PMA Approved. Made in USA.

CURTIS PLT-275AV Flush Valves 6 Holes' Adapter Plates Assembly.

Product Specifications:

Diameter: 2.75 in.

Depth: 640,000-650,000

From Mounting Surface to Bottom Hole Diameter: 1-1/2 in.

Not Certified

Aluminum valve as used in production aircraft with Model A-110 master cylinders for dual brake installations. Complete with AN flare fittings.

LORD manufactures a range of vibration and motion control products for General Aviation aircraft including elastomeric and non-elastomeric mounts, full structures, yokes and attachments. Their Dynafocal engine mounts are available for many aircraft, including the most produced general aviation fixed wing aircraft models, such as the Cessna 152, Cessna 172, Cessna 182, Piper PA-28 series, and more. For additional information please also refer to the attached Lord Catalog.

Manufactured to the highest standards, the Andair standard fuel selector range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. Duplex fuel selectors are also offered  (see separate product presentations). FS16, FS20 and FS25 series of fuel selectors are designed for safety, provide a precise and smooth feel in operation  and come in different types, ranging from Type 1 ON/OFF shut off valves to valves with multiple positions. To prevent the pilot switching the wrong tank or turning the fuel off they feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off.

FS20 series 3/8" fuel selectors provide a choice of lower and side fittings, and all units can be operated with an extension and universal joints. They come in the following types:

Type 1 (FS20-1): simple 3/8” ON/OFF shut off valve with 90 degrees action between the two positions. There are two ports and either port can be used as the inlet or outlet.

Type 2 (FS20-2): Three way 3/8” fuel selector with positions LEFT-RIGHT-OFF and a 90 degree action between each tank selection. No lower fitting for use where there is little space behind the valve. 

Type 3 (FS20-3): three way selector with the positions LEFT - RIGHT - OFF. Generally used in low wing aircraft with a tank in each wing.

Type 4 (FS20-4): Designed for high wing aircraft, it has four lever positions OFF - LEFT - BOTH – RIGHT with a 90 degree action between each position.There are 3 ports. The lower port is the outlet to the engine and can be Male AN-6, Female 1/4NPT or a  360 degree Banjo adjustable fitting with a male AN-6 end.

Type 5 (FS20-5): 4 way Fuel Selector ( 3 tanks and OFF ) with positions LEFT - MAIN - RIGHT - OFF, each at 90 degree intervals.

Type 7 (FS20-7): Newest in the range 3 way fuel selector with positions LEFT - RIGHT - OFF. The inlets are at the 45 degree positions, to the LEFT and RIGHT, and the outlet is at the base of the valve. FS20-7 has been designed for centre consol mounting.

Type 8 (FS20-8): 5 way Fuel Selector ( 4 tanks and OFF ) with positions LEFT TIP - LEFT - RIGHT - RIGHT TIP - OFF, each at 72 degree intervals. 

For additional information please refer to the product presentations, the supplied documentation or contact us.

McFARLANE® AVIATION MC0543022-2 Series FAA-PMA approved nose wheel steering rods s are intended for use on for Cessna 172 series aircraft replacing respective OEM steering rod,tube assemblies.They feature new re-designed long-life springs, hardened internal washer for greater durability, stainless steel tubes for improved corrosion resistance  and optimum performance even after years of service.

Cessna Models' Application List:

172D,E,F,G,H,I,K,L,M,P

P172,

R172K

F172D,E,F,G,H,K,L,M,N,P

FP172

FR172E,F,G,H,J,K

172R

172S

Aircraft hydraulic pumps are used to move non-compressible fluid through an aircraft hydraulic system. This power is often used on small airplanes to operate wheel brakes, retractable landing gear, and some constant-speed propellers. On larger airplanes, hydraulics are used for flight control surfaces, wing flaps, spoilers, and other systems. Aircraft hydraulic pumps are normally engine driven, but sometimes to simplify the system manufacturers use an electric motor to drive the hydraulic system. These hydraulic power packs incorporate a reservoir, control valve and auxiliary valves into a single unit.

As the OEM for the PRESTOLITE Power Packs, AEROSPACE TURBINE ROTABLES Inc.applies an extensive overhaul and testing process to ensure a long and reliable operation of PRESTOLITE Hydraulic Power Packs offered as Overhaul/Exchange (*).  

(*)requires the return of the old unit and its exchange by an overhauled one. The supplier maintains the right to check the condition of the returned unit before the exchange. The price also applies to the hydraulic power packs shipped for overhaul of the same unit and return. 

When intended for use on certified aircraft applications, PRESTOLITE Overhaul/Exchange Hydraulic Power Packs come with Dual Release (FAA/EASA) Certification . It must specified at the time of ordering as additional charges may apply.

For additional information please consult the supplied documentation.

The PARKER AIRBORNE designs and manufactures motor driven fuel fuel  boost and transfer pumps and is part of the PARKER AEROSPACE GROUP of the PARKER HANNIFIN CORPORATION. These pumps consist standard equipment by the world's leading airframe manufacturers. The PARKER AIRBORNE product range includes:

- In Line fuel pumps for low-flow fuel applications,

- Submerged Centrifugal fuel pumps,

- High Performance Centrifugal fuel pumps for use in turboprop or turbofan jet aircraft,

- Submerged Duplex fuel pumps with two distinct pumping elements

The PARKER AIRBORNE fuel boost pumps use 28 V direct current (DC) to drive a highly efficiency, brushless DC (BLDC) motor or 115.5 V alternating current (AC) three-phase induction motors. The BLDCmotor-driven pumps incorporate integral electronic controllers using Hall Effect sensor rotor-position feedback. The hardware-only controller doe not use any software or programmable logic devices. These pumps feature:

-fuel cooled motor and electronics

-fuel wetted carbon bearings allowing for long-life fluid film design with no rotating shaft seals

-a high efficiency brushless DC (BLDC) motor or a three-phase induction motor

-qualification for high levels of lighting and electromagnetic interference (EMI).

The PARKER AIRBORNE fuel boost pumps can be furnished as either NEW, NEW EXCHANGE or OVERHAUL EXCHANGE. 

Offered pumps in OVERHAUL Condition are supplied in accordance with FAA-approved process specification, come with a FAA Form 8130-3 and can be provided in exchange of existing customer owned units (cores). In all EXCHANGE cases,  the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders with us when our co-operating supplier verifies that the unit is in a reasonable condition. For additional information please consult the supplied documentation (*) or contact us.

In addition to the PARKER AIRBORNE pumps, RAPCO FAA-PMA approved pumps are also offered as direct replacements  to the respective PARKER AIRBORNE models. The RAPCO replacement pumps can be furnished as either NEW EXCHANGE or OVERHAUL EXCHANGE (please refer to their separate product presentation).

(*) The supplied documentation is to be used for reference only. When selecting a part for installation consult the appropriate aircraft maintenance manual, parts catalogue, or equipment list for approved data.

The 90340/90375 Series wing tip mounted light systems from WHELEN AEROSPACE TECHNOLOGIES (WAT) combine  strobe anti-collision/LED position lights, eliminating the need for a tail mounted position light. 90375 Series is same as 90340 with the addition of 3 feet of braided bonded protection for use in composite wingtip structure. They can be direct replacements (exact footprint) for the Whelen Model A600PG/PR series without replacing the current strobe power supply. The LEDs in position lights provide a significant reduction in current draw over conventional light bulbs. The strobe light lens assembly is radio shielded for maximum EMI/RFI protection. Single set of flying leads operates both forward & tail nav on 28 VDC version, and one set each of flying leads for the forward & tail nav on the 14 VDC version. FAA TSO'd.

Product Specifications:

LED Navigation Light Power Consumption: 0.5 amps @ 14 VDC, 0.25 amps @ 28 VDC 

Weight: 0.60 lbs. (272gm) 14 VDC, 0.65 lbs. (295gm) 28 VDC 

Exposed Height: 2.70” (69mm) 

LED Colors: Aviation Red, Aviation Green & Aviation White 1.1 lbs. (499gm) 

Lens: Clear RFI coated glass: strobe, Clear Polycarbonate: Navigation Lights

Military Specification MS35058 Series Toggle Switches can be used to upgrade your aircraft's cockpit controls. These heavy-duty metal switches have a standard shape that works well for a variety of applications can be used for most components that only function in either the on or off positions. They are available in several sizes to fit your particular airplane and are shipped with all necessary rings and hardware for installation. Toggle switches are available with two or three operating positions, 1 or 3 hole mounting and a variety of circuitry & electrical ratings. Contacts are made of solid silver. Wide usage is found in aircraft, mobile, marine, electronic and industrial applications. Available in full "AN" standard size & Ultra Miniature 1/2" size, contact types and circuit codes (see reference chart).

This new MERCURY MARINE Mercruiser replacement Trim Pump replaces the older P/N 14336A17 trim pump. Used on MERCURY MARINE Mercruiser Alpha One, Alpha Gen II and Bravo Drive applications. Matched to the larger new style trim cylinders.

The HEIM® BEARINGS company has been acquired by RBC® BEARINGS, a leader in the world of highly engineered bearing products. 

HEIM® BEARINGS produces the industry's widest range of rod end bearing sizes (aka rod ends) in  the following four grades (types): precision, aircraft, military and commercial with each grade including different series suitable for respective application requirements. HEIM® BEARINGS are made from different materials featuring among others high strength two piece designs, high capacity designs, self-lubricating options and thermoplastic races or Teflon® liners. Please consult the supplied table on different grades and series offered.

- Precision rod ends are manufactured to tight tolerances for applications requiring improved linkage accuracy and reduced looseness. 

- Aircraft rod ends use premium materials, and have magnafluxed rod end bodies. Originally intended for aircraft applications, aircraft rod ends are used in many industrial applications where a high degree of reliability is required

- Military rod ends are produced in strict accordance with all applicable military specifications and are typically used in military and commercial aviation applications, or when Mil-Spec approval is required

- Commercial rod ends are produced using standard materials and manufacturing methods, and consist an economical choice for industrial applications

The HEIM® BEARINGS ME/AS81935/1 and FE/AS81935/2 series are military standard, high capacity self lubricating rod ends, male and female threaded respecively, using HEIM® UNIFLON® liner approved to SAE-AS81820 (formerly MIL-B-81820). Their rod end bodies are made from 4340 alloy steel, heat treated, magnetic particle inspected, cadmium plated and chromate treated. Balls  are made from 440C on 17-4PH race inserts and heat treated.

Letters “L” and “K” to prefix indicate Left Hand thread and Keyway respectively.

Please refer to the supplied chart for technical specifications and the RBC® HEIM® Bearings Catalog for additional information.

OMRON A3C series cylindrical pushbutton switches have the basic design as the M2C Series cylindrical indicators. They provide a high-intensity uniform surface lighting while they have a miniature size with excellent feeling of operation. They have a cylindrical 20-mmX12-dia. body making panel cutouts easier. These switches are offered in lighted and non lighted versions, different colors, display shapes, with LED or incandescent lamps and different socket units. Please consult the attached documentation for ordering.

When there is a need for connection of a set of electrical wires, terminal blocks provide a safe & convenient way to keep them organized. AVIATIONEU NEW ERA TR series of snap on (clip type) terminal blocks allows for terminal block assemblies to be installed and realeased fast and easily. Terminal block connectors are rugged, easy to use and designed to keep wires of varying gauges securely connected. They can be mounted on the 35/7.5mm DIN rail of 1 or 2 meter length made from aluminum or zinc plated steel which is in turn can be mounted on control panel backplates. Any pole assembly is possible. With the use of a DIN rail protective conductor terminal block, the rail itself can be used as the grounding terminal block.

The connectors are offered in black color (or other colors as per customer requirements), with a rated voltage of  600V and different rated current options (10A,20A,30A or 40A). They are sold in packs of 100 pieces each and come with paper marker strips & transparent cover. DIN mount rail & accessories are available at additional cost. These can be ordered only together with the terminal blocks. Appearing prices are for reference only. Contact us for a quotation.

McFARLANE® AVIATION MS27975-1 fork rod end is internally threaded 1/4"-28 to fit threaded 1/4" diameter rod. Manufactured from 4130 steel. Used for engine controls.

Miniature incandescent and LED lams (bulbs) sourced from different manufacturers such as GENERAL ELECTRIC (GE), NORMAN LAMPS, AMGLO KEMLITE LABORATORIES,AERO-TECH LIGHT BULB Co. and others, for use in various aircraft applications (cockpit/wing/tail lights).

Unless a specific manufacturer is mentioned at the time of ordering and the selected lamp model is in production by this manufacturer, alternative lamps from different manufacturers shall be provided meeting the same or equivalent specifications.

 GE Lighting has been acquired by Tungsram. All bulbs are identical, but packaging may differ at the time of shipment.

Filler opening caps are parts basically circular in shape, designed to cover or seal the filler-neck or inlet opening of a fuel tank, radiator, oil reservoir, liquid storage tank or the like. They are either permanently attached or provided with a means of removal and replacement. 

Pressure refuel caps are used to lock, seal, and vent the pressure refuel port for an aircraft fuel tank. Pressure refueling allows for single point refueling on larger aircraft and can be used with all aircraft fuels. To fuel the aircraft, the caps are manually actuated by pressing down on the handle, which will vent and unlock the cap for removal by twisting. The cap remains attached to the aircraft by a lanyard. Once refueling is complete, the cap is inserted back onto the adapter and twisted until locked into place, which effectively reseals the pressure refuel port.

Pressure refuel caps are offered by different manufacturers such as Parker Aerospace, Eaton Coporation and others. They are designed in accordance with military specification MIL-C-8605B (for technical requirements) and MS29526-2(for envelope requirements).

Those from Parker Aerospace are 4.5 inches diameter, with an indexing feature and they fit into a 2.5-inch pressure refuel adapter per military specification MS24484. Their main features include an aluminum base and handle, a fluorosilicone O-ring seal, and antisparking brass chain lanyard (per industry standard RR-C-271) with a plastic tubing cover and corrosion resistant steel hooks.  Lanyards can also be fabricated with corrosion-resistant steel or flexible plastic and fuel resistant tubing. Optional features are also available such as key lock, ventilation, hinge, visual fluid level indicator, dust cover easy-lift handle and contoured adapter.

For additional information please consult the supplied documentation or contact us.

MICHELIN® Aircraft Tyres is internationally recognized as the No.1 tire manufacturer in the world. The company provides bias tires, radial tires, and tubes for aviation customers around the world, in a range of applications including commercial and regional airlines, general aviation and military aviation. 

MICHELIN® AIR® X® Aviation Radial Tires are currently mounted on a wide range of commercial, military and corporate aircraft. Given the numerous advantages they offer over conventional bias-ply tires, these tires have elevated the basic performance expectations for aircraft tires, the same way MICHELIN® radials raised the standards for automobile tires. Offered in NEW or USED (RETREAD) (*) Condition. Compared to bias tires, MICHELIN® AIR® X® radials offer:

Measurable Fuel Savings

More Landings Per Tread

Improved Cut Resistance

Key features of MICHELIN® AIR® X® radials include:

Light Weight Radial Design. They typically weigh 20–30% less than comparable bias tires, and they operate at cooler temperatures. This leads to measurable fuel savings, more landings per tread, longer wear characteristics and a more stable contact patch than bias tires, as well as shorter turnaround times and reduced carcass fatigue.

Extra Strong Carcass. Michelin’s carcass design helps restrict tire growth and the stretching of rubber resulting in better cut resistance than bias tires.

Optimized Tread. Durable cut-resistant tread includes deep skid depth and specially-designed circumferential grooves. This contributes to an extended tire life, less heat build up and lower maintenance costs due to fewer tire changes.

Customized Rubber Compounds. Sidewall is optimized for both ozone and ultraviolet light protection which helps reduce ozone cracking in key areas of the tire. Provides maximum amount of exterior wear and crack resistance for a long tire life.

Flexible Casing. The casings of MICHELIN® AIR® X® radials is more flexible than casings used in bias tires. This results in noticeably smooth operating characteristics during taxiing, landing and takeoffs.

Please refer to the supplied documentation and the Reference & Application Chart for additional information.

(*) Retread tires have undergone a remanufacturing process to replace the worn tread on used tires with new tread to help extend the life of the tire. The number of times the  tread has been replaced in the tire casing is indicated by a number just after the letter "R" in the product reference number (SKU), namely R1, R2, R3 and so on.