RAMI AV-100 Antenna is intended for use with an ELT (Emergency Locator Transmitter) for general aviation. It has a passive two frequency (121.5 & 406 MHz) wire whip, designed for low speed aircraft (up to 250 knots).

Product Specifications:

Application: Airborne ELT

Frequency: 121.5 MHz, 406 MHz

Impedance: 50 Ohms Nominal

VSWR:

121.5 MHz 2.0:1 Maximum

406 MHz 1.5:1 Maximum

Polarization: Vertical

Pattern: Omni-Directional

Connector: "BNC" Female

Weight: 3 oz. Maximum

FAA TSO: C126a

Color: Black

For use with most GPS and TAWS systems. Works well with most of today's mode S transponders.

PS ENGINEERING has revolutionized audio control in general aviation airplanes. At that time, the original PMA6000 took the audio panel from a collection of switches added as an afterthought, to a multitalented intersystem focal point for cockpit audio.

Radio selection, cockpit communications and even music were seamlessly combined in the modern audio control panel. The PMA6000-series set a benchmark for all GA audio panels that followed.

The next generation PMA6000B benefits from PS Engineering's long experience of audio panel control design and manufacturing experiences. It is an excellent low cost audio panel alternative to the higher end systems that PS Engineering has become so famous for. 

The PMA6000B combines an audio selector panel with a top-quality manually adjusted 4 place VOX mono intercom and a slew of features to enhance versatility and utility. The PMA6000B holds both FAA TSO as well as EASA ETSO and was designed to be made easier to install because of a single 44-pin Sub-d connector. Different PMA6000B models offered with or without marker beacon receiver.

Product Features:

Built-in 4 place mono intercom PS Engineering's ""Set-it and Forget-it"" manual VOX

Optional built-in marker beacon receiver

Split mode for dual audio capability

2 - Com Capability

3 - Intercom isolation modes - Pilot Isolate, All, and Crew

2 - Music inputs with Soft Mute™

2 - Unswitched inputs

6 - Switched inputs

A patented ""swap"" function allows selection of Com 1 or Com 2 from remote pushbutton

Fail-safe feature automatically hard-wires the pilot to Com1 in the case of an outage

Single 44-pin connector making installation easier

Certification: FAA TSO/EASA ETSO

Warranty: 24 months

The COBHAM Antenna Systems' COMANT product range includes aviation antennas focusing on GPS, Communications and Navigation products for General Aviation, light Jets and helicopters.COMANT antennas offer a wide variety of fit, form and function options that will fit nearly every need. Comant antennas are compatible with a number of varying applications and effective in a number of differing environments. The range includes Radiophone, DME, VHF, VOR, LOC, GS, DME, Transponder, FM, AM, UHF, L Band, ELT, and COMDAT antennas.

ETSO'd Slimline Panel Mounted 10 W VHF Radio with built in 2-place intercom with auxiliary inputs for stereo music and audio warnings. Available with 8.33 kHz or  25kHz frequency spacing options.

Stratus ESG digital transponders by APPAREO have been designed with non-glass panel aircraft in mind. Different models are offered for non certified and certified aircraft. Stratus ESG transponders feature 1090 ES (Mode-S extended squitter), 310 W nominal power output, a built-in WAAS GPS, compliance with global mandates for ADS-B Out transponders, push-button operation with modern keypad makes entering a squawk code easy, easy-to-use interface and pressure altitude monitor. Their form-factor enables easy replacement for existing transponders.

Version for non certified aircraft is offered as unit only or together with wire pigtail.

The version for certified aircraft is TSO'd and can be used to replace existing transponders in a wide range of aircraft models from different aircraft manufacturers like Cessna, Piper, Beechcraft, Mooney, Diamond and others. Certified units can only be shipped to a certified Appareo installer.

Product Specifications:

Bezel Height: 1.69 in. (43 mm)

Bezel Width: 6.38 in. (162 mm)

Depth: 10.75 in. (273 mm) front of panel to connector backshell

Weight: 3.29 lbs. (1.49 kg) including rack and connectors

Operating Temperature: -20°C to 55°C

Storage Temperature: -55°C to 85°C

Power Input: 9.0 to 36.0 VDC, 15 W typical

Cooling Input: No fan required

Environmental Compliance: DO-160G

Software Compliance: DO-178B Level C

Hardware Compliance: DO-254 Level C

TSO Compliance: C112e (Level 2els, Class 1), C145d (Class Beta 1 GPS/WAAS), C166b (Class B1S)

Display: OLED

Transmitter Power: 310 W

Solid State Cockpit Voice Recorders (SSCVR) and Flight Data Recorder (FDR), aka "black boxes", are required by Civil Aviation Authorities to be installed in large commercial aircraft and some smaller commercial, corporate, and private aircraft used to help reconstruct the events leading to an aircraft accident. Manufactured by various manufactuers such as HONEYWELL AEROSPACE, UNIVERSAL™ AVIONICS and others they are offered in different models, as CVR, FDR or combined systems, certified by FAA, EASA and other CAAs and available in NEW Condition but also as USED (OVERHAULED) units for straight purchase or exchange. For additional information please consult the Product Description section, the supplied documentation or contact us for a quotatin.

Automatic portable radio beacons (ELT(AP) АРМ-406П (ARM-406P), АРМ-406П1 (ARM-406P1) and АРМ-406АС1 (ARM-406AC1) are safety devices designed to transmit via satellite to the stations COSPAS-SARSAT distress radio signals with aircraft coordinates received from the onboard computer system.Such information facilitie identification of the aircraft and guidance of S&R facilities to the accident site. Located in the aircraft cabin these devices offer the possibility of quick use in an emergency.

The automatic portable radio beacon АРМ-406П1 (APM-406P1) includes:

- monoblock P, consisting of a double protective casing with shock absorbers installed in it, an overload sensor (DP) and an AC1A monoblock;

- remote control PDU-406 (ПДУ-406) installed in the cockpit;

- external antenna ANT-406VA (АНТ-406ВА), mounted on the aircraft body.

The АС1А monoblock is  a portable radio beacon, including a PM-AC1A (ПМ-АС1А) transmitting module, an АРМ-043-01 autonomous power supply unit and an ANT-APM-01 (АНТ-АРМ-01) antenna. The emergency mode of operation of the AC1A monoblock can be switched on both from the remote control and from the DP, as well as manually when removing it from the protective casing when leaving the emergency aircraft.

Autonomous power supply (APS) units are also offered for use with the radio beacons. АРМ-043 (CDKT.436140.590) 14.4V are intended for use for beacons manufactured before 2013 while АРМ-043-01 (CDKT.436140.590-01) 10.8V for beacons manufactured after 2013. Unless otherwise specified their replacement frequency is once every 3 years with a 3-year self life.

For additional information please refer to the supplied documentation or contact us.

ETSO'd Slimline Panel Mounted 16 W VHF Radio with built in 2-place intercom with auxiliary inputs for stereo music and audio warnings. Available with 8.33 kHz or  25kHz frequency spacing options.

The GARMIN® GTN 650Xi (*) GPS/Nav/Comm/MFD panel-mount platform replaces discontinued GTN 650 (**) offering more pixels, processing power, speed and performance.  It’s approved for installation in many of makes and models of fixed-wing aircraft and helicopters providing high-resolution terrain mapping, graphical flight planning, traffic target surveillance, multiple weather options, taxiway diagrams and a host of other advanced navigation features. It comes with Americas or International Database (specified at the time of ordering).

The GARMIN® GTN 650Xi features:

- a brighter, faster, sharper, better Do-It-All intuitive touchscreen interface providing quick access to navigation, radio tuning, multifunction display features and more,

- powerful fast response dual-core processors boosting the GTN Xi series graphical display capabilities — with faster zooming, panning and map rendering on the display,

- high-resolution  4.9” display with almost double the pixel count of its predecessor and wider viewing angles,

- multi-function display cpability supporting multiple inputs of moving maps, terrain, traffic, weather, airport diagrams and more,

- easy data entry with the use the on-screen QWERTY keyboard or traditional concentric knobs to enter frequencies, waypoint identifiers, routings and more,

- Telligence™ voice control technology helping reduce pilot workload by responding to hundreds of spoken commands with the press of a button on the yoke,

- finger swipe gestures enabling pilots to pan across the map display or use a smartphone-like pinch-to-zoom motion to scale up or down on any map, traffic or terrain page.

GARMIN® GTN 650Xi Specifications

TSO applicability: C34e; 2C34f; C36e Class A; 2C36f Class A; C40c; 2C40c; C74d Class A; C112e; C128a; 2C128; C146e Class 3; C151d Class A, B; C157b Class 1, 2; 165b; C169a Class C, E, 3, 4, 5, 6; 2C169a Class C, E, H2, 3, 4, 5, 6; C194; C195b Class B1, B3, B5, B7; C209

Display size: 4.9" (125 mm) diagonal

Display resolution: 834 pixels (W) x 370 pixels (H)

Unit bezel height: 2.65" (67 mm)

Unit bezel width: 6.25" (159 mm)

Unit depth with connectors: 11.25" (286 mm) (measured from face of aircraft panel to rear of connector backshells)

Unit weight: 5.5 lbs (2.48 kg)

Input voltage range: 11 VDC - 33 VDC

Operating temperature range: -20° C to 55° C (-4° F to 131° F)

Number of GPS channels: 15 (12 GPS and 3 GPS/WAAS/SBAS)

LAT/LON position accuracy: <1.25 meter RMS horizontal, < 2 meter vertical, with WAAS

Maximum velocity: 1,166 knots

Position update Interval: 0.2 sec (5 Hz)

Notes:

(*) The GARMIN® GTN 650Xi can be supplied as kit with 4 feet pigtail wire harness without certification . If cerification is required installation must be done by a GARMIN® Authoried Service Center.

(**) The GARMIN® GTN 650 can be supplied as USED (Serviceable) Certified unit (FAA 8130-3 Form) with GPS antenna, rack, connector, existing Database, 6 nonth warranty.

The FLIGHTCOM 403MC is a 4-place panel mount, easy to use, voice-activated mono intercom with 3-position transmit capability designed to fit almost anywhere in the panel.

GARMIN® GMA 245 Audio Control Panel draws on Garmin audio technology for “home theater” quality sound. Offers instant upgrade as a slide-in replacement for older GMA 240 and GMA 340 units installed in experimental and light sport aircraft.

Key features include: 

Bluetooth wireless connectivity for easy access to phone calls & audio entertainment (1 device allowed connection)

Audio Inputs: 3 Transceivers (including TEL), 5 Receivers (NAV1, NAV2, AUX1, AUX2, AUX3)

3D audio processing helping pilots to “locate” inputs coming into their headsets

6 Position Intercom: pilot, co-pilot, 4 passengers with 2 volume controls by pilot/co-pilot or passengers

Clearance playback

Impressive audio mixing and distribution

USB charging port powering smartphones, tablets, music players and more

For additional information please consult the Product Description section and the supplied documentation.

Installation parts and accessories for GARMIN® Audio Control Panels are sold separately. Please refer to the respective product presentation.

GARMIN® GTX™ transponder product line includes Mode A/C and Mode S TSO'd panel mounted transponders offered in a‭ ‬wide variety of configurations to choose‭ ‬from‭, ‬depending on desired functions‭.‬ Different models are listed under separate product presentations. 

GARMIN® GTX™ 325  is a Mode A/C panel-mounted full-featured, TSO'd certified transponder offering a simple, affordable replacement for standard Mode C transponders. It features aural alerts, total air temperature (TAT), pressure altitude readout, altitude monitor function, density altitude readout, built-in timers and automatic ALT/GND mode.  ‬It replaces the popular GTX™ 327 ‬and is essentially the same unit‮—‬but carries the GTX™ 335/345‭ ‬display and button layout‭. ‬It would be a meaningful ‬choice for the replacement of an older Mode C ADS-B‭ ‬Out transponder. 

EASA Certified VHF transceiver with 6W output power and 8.33kHz frequency spacing.

The HONEYWELL BENDIX KING® KY 196A/197A series of TSO'd VHF COMM transceivers have a flatpack design, measure 1.3" x 6.3", weight just 2.8 pounds and have the same capabilities except that the 28-volt KY 196A delivers 16 watts and the 14-volt KY 197A 10 watts minimum transmit output power. Both incorporate solid-state construction and feature 9 pilot-programmable memory channels (11 including those in "USE" and "STBY"), flip-flop frequency transfer between active and standby frequencies, a 118.00MHz to 136.975MHz operating range and a digital frequency synthesizer generating 760 COMM frequencies. Despite their wide range of capabilities, KY 196A/197A radios were designed to be easy to read and logical to operate. An audio leveling feature automatically amplifies weak audio signals and mutes strong signals. Racks & connectors (for new installations) and manuals are sold separately. 

The HONEYWELL BENDIX KING® KY 196A/197A  VHF COMM transceivers are available in different versions  including those with Silver Crown Plus faceplates. They can be furnished in NEW condition or as USED in Serviceable or Overhauled conditions indicated respectively by the letters "SV" and "OH" in the product reference numbers (SKU and  accompanied by the relevant certification (e.g. yellow tag, 8130-3 form). They are also offered as exchanges / trade-ins  for returned customer owned units indicated by the letter "EX" in the SKU.  In the case of an exchange/trade-in option of a customer unit, the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders when our co-operating supplier verifies that the unit is in a reasonable, repairable condition. It is recommended that this option is selected by our customers mainly for upgrades and only in cases when their units are functioning properly at the time removal from the aircraft. In cases when customer units are found by our supplier to be non-repairable, the core deposit shall not be refunded and shipping charges shall apply if customers wish the return of these units to them. Please refer to the Product Description section for technical specifications and information on USED avionics.

The ICOM A25 series are powerful air band handheld transceivers offered in communications only (A25C) or NAV/COM versions (A25N) with 6 watts of power and an IP57 waterproof rating. They include a large 2350mAh Li-ion battery, providing a long operating time. The easy-to-use interface and large 2.3-inch LCD display combine to provide stress-free programming and in-flight operation. Built-in Bluetooth®, GPS and VOR navigation. ICOM A25 transceivers come with Antenna, Belt Clip, Handstrap, Battery Case, Battery Pack, Headset Adapter, Power Adapter and Battery Charger.

The GARMIN® GTX™ 345 looks and operates like a standard Mode S transponder. It is a panel-mounted  IFR-certified all-in-one transponder solution for compliance with 1090 MHz ADS-B "Out" and "In" requirements with minimal expense, downtime and disruption to the aircraft panels while providing at the same time all the weather and traffic benefits of ADS-B “In”. An easy replacement for existing transponders with common 1.65-inch tall form factor, FAA and EASA approved for installation on most popular aircraft makes and models. It features a bright, sunlight-readable digital display, a pressure altitude readout, handy timers for approaches and other operations, plus dedicated pushbuttons for quick and easy squawk code entry. Its 1090 MHz ADS-B "Out" transmission capability enables automatical output of accurate and dynamic traffic surveillance data that the NextGen airspace system requires. Its ADS-B "In" reception unlocks even more capabilities for pilots, enabling display of ADS-B traffic, weather and more on a variety of installed or portable displays. Traffic monitoring requirements of ADS-B can be satisfied by either a WAAS/SBAS-compliant navigation system or an optional built-in GPS position source available with your GTX 345 transponder.

Optional remote mount GTX versions are also available for compatibility with the GTN™ 750/650 series of GPS/Comm/Nav systems, as well as select Garmin G1000® integrated flight deck systems – all of which provide built-in remote transponder code selection and control.

With the GTX™ 345, the subscription-free weather and traffic display capabilities enabled by ADS-B "In" can be interfaced with compatible cockpit displays or streamed wirelessly via Garmin Connext™ to aera 796/795 or 660 series portables, as well as to popular tablets/mobile devices by way of apps such as Garmin Pilot™, or ForeFlight Mobile. 

The GTX™ 345 ADS-B dual-link receiver can receive on both frequencies (978 MHz and 1090 MHz) authorized for ADS-B operations in the U.S. ADS-B traffic and active traffic targets are merged on the display providing a truly comprehensive traffic picture. For added situational awareness, it also incorporates a built-in audio output for audible traffic and altitude alerts, which can be integrated into the existing audio panel. 

The GTX™ 335/345 transponders can only be sold for use in experimental aircraft. Their use in certified aircraft requires their installation from a shop certified by Garmin to perform installations.

Air Avionics is the common brand for Garrecht Avionik GmbH and Butterfly Avionics GmbH.  VT-2000 is a modern 6.25" rack format Mode-S/ADS-B EASA Certified Transponder (EASA Approval No. EASA.21O.705) with an integrated keyboard for easy operation. It can be installed as a direct replacement for the popular Bendix-king KT76 / KT76A/C series of transponders without any changes to pre-existent wiring and mounting trays. A special mounting tray (sold separately) is available for new installations. It has an integrated internal altitude encoder (alticoder) or or can be connected to any kind of existent alticoder in the aircraft (parallel and serial).

Product Features:

Installation without adapter and modification of existing wiring harness. Just slide in into existing mounting frame of your KT-76 or KT-76A / KT-76C.

Interfaces for future applications (i.e. ADS-B, TIS)

Certification base: ETSO-2C112a, ED-73B

Output power: min. 220 Watt (Class-1) Level 2es (extended Squitter)

Internal Alticoder

Interfaces für external alticoder (serial or parallel)

Direct-GPS NMEA Interface for ADS-B, no adapter required

Transflective color TFT Display

Illuminated keyboard