CMM Series male-to-male in-line check valve with compact overall length. CMM check valves are available in brass, steel and stainless steel and in different sizes.

High Pressure Strut Valve with Small Diameter Thread Adapter. Fits in nose gear of certain Cessna models.

Manufactured to the highest standards, the Andair standard fuel selector range incorporates 1/4"(FS16), 3/8"(FS20) and the 1/2"(FS25) valves. These valves allow for multiple tank switching of one fuel line. Duplex fuel selectors are also offered  (see separate product presentations). FS16, FS20 and FS25 series of fuel selectors are designed for safety, provide a precise and smooth feel in operation  and come in different types, ranging from Type 1 ON/OFF shut off valves to valves with multiple positions. To prevent the pilot switching the wrong tank or turning the fuel off they feature  a large red lever with 'Fuel' engraved on it and a clearly labelled fascia plate to indicate which tank has been selected. It allows for a good solid detent at each tank position and also the button on top of the lever must be raised to switch the fuel off.

FS20 series 3/8" fuel selectors provide a choice of lower and side fittings, and all units can be operated with an extension and universal joints. They come in the following types:

Type 1 (FS20-1): simple 3/8” ON/OFF shut off valve with 90 degrees action between the two positions. There are two ports and either port can be used as the inlet or outlet.

Type 2 (FS20-2): Three way 3/8” fuel selector with positions LEFT-RIGHT-OFF and a 90 degree action between each tank selection. No lower fitting for use where there is little space behind the valve. 

Type 3 (FS20-3): three way selector with the positions LEFT - RIGHT - OFF. Generally used in low wing aircraft with a tank in each wing.

Type 4 (FS20-4): Designed for high wing aircraft, it has four lever positions OFF - LEFT - BOTH – RIGHT with a 90 degree action between each position.There are 3 ports. The lower port is the outlet to the engine and can be Male AN-6, Female 1/4NPT or a  360 degree Banjo adjustable fitting with a male AN-6 end.

Type 5 (FS20-5): 4 way Fuel Selector ( 3 tanks and OFF ) with positions LEFT - MAIN - RIGHT - OFF, each at 90 degree intervals.

Type 7 (FS20-7): Newest in the range 3 way fuel selector with positions LEFT - RIGHT - OFF. The inlets are at the 45 degree positions, to the LEFT and RIGHT, and the outlet is at the base of the valve. FS20-7 has been designed for centre consol mounting.

Type 8 (FS20-8): 5 way Fuel Selector ( 4 tanks and OFF ) with positions LEFT TIP - LEFT - RIGHT - RIGHT TIP - OFF, each at 72 degree intervals. 

For additional information please refer to the product presentations, the supplied documentation or contact us.

DYNON AVIONICS AOA/Pitot probes perform two functions: airspeed and angle of attack sensing. These functions require having two pressure ports on the tip of the probe. The normal pitot pressure port is on the front face of the probe and is designed to be insensitive to angle of attack. The second pressure port is located on an angled surface just under the pitot port and is designed to be very sensitive to AOA. They are under-wing mount, L-shaped  probes which can be installed  easily with simple plug-n-play integration with Dynon and Advanced Products.Their installation requires a mounting bracket sold separately. The pressure from each port is delivered via separate air lines to the instrument where they are compared to previously calibrated scenarios specific to the aircraft. Competitively priced, they are offered in Non-Heated and Heated versions. The Heated AOA Pitot includes a nichrome heating element that is regulated by a separate pitot heater controller unit supplied with the pitot. The controller actively monitors a temperature sensor embedded within the pitot head and regulates the power to maintain a constant temperature. This not only conserves energy but additionally prolongs the life of the heater. The controller also outputs a signal that can be wired to a warning light in the cockpit to warn the pilot anytime there is a malfunction or that the pitot is turned off.

The company SPECIALITY TIRES OF AMERICA (formerly McCREARY TIRE & RUBBER providing automotive tires) manufactures a wide range of aircraft tires under different brands including SUPER HAWK®, AIR HAWK®, AIR TRAC®, AERO CLASSIC® & AERO TRAINER® as well as matching tire tubes. Different brands (series) briefly presented below are separately listed. For more information please refer to the supplied documentation.

SUPER HAWK® tires are the best choice when  the highest levels of performance and extra-long tread life are required. Designed to handle higher landing speeds and heavier loads, these tires combine advanced design & over 90 years of precision tire craftsmanship resulting in premium belted aircraft tires that surpasse FAA specifications and match the performance of more expensive brands.

AIR HAWK® tires are premium grade & priced tires, but provide longer service life. Excellent choice for a wide range of applications. Improved tread compounds and high-strength casings offer added wear resistance and an extra measure of security. AIR HAWK® tires are FAA approved and tested by thousands of pilots, delivering a reliable, cost-effective performance under a wide variety of takeoff and landing conditions. 

AIR TRAC® fine nylon cord narrow-ribbed, oval shaped tires are designed for soft field applications and rigidly tested to meet FAA Standard TSO-C62. The  AIR TRAC  tires consist an excellent choice for single engine, piston aircraft. Thesy are ideal for aircraft operated on grass strips while being perfectly usable on hard surfaces. These tires are are original equipment on many of today’s aircraft and offer a great performance in an economical tire. AIR TRAC® tubes are the perfect match to the AIR TRAC®  tires. 

AERO CLASSIC® tires are designed specially for classic planes including warbirds, DC-3's, and Beech 18's, often the only manufacturer producing tires for these aircraft. The product line includes over 50 tires and tubes, from 8" diameter for tailwheels, up to 56" diameter C-130 inner tubes. AERO CLASSIC® tubes are tested to MIL-I-5014F standard. 

AERO TRAINER® tires are designed for flight schools with single engine trainers. They combine the high quality and durability with a competitive price.

SPECIALITY TIRES products are supplied with a standard Certificate of Conformance. If an FAA/EASA Form is needed (depending on the ordered item) please mention this during the order placement. In this case, additional cost may apply.

LED lighting is the ideal technology for aviation applications. Whelen LED lights are time and field-tested for reliability and long-life performance under the tough conditions required by Fire, Emergency, DOT and Law Enforcement professionals around the world.

PARMETHEUS PLUS PAR36 LED lights by WHELEN AEROSPACE TECHNOLOGIES (WAT) are FAA-PMA Approved LED lights with a convenient “Drop In” design for ease of installation, intended for use as direct replacements for outdated PAR36 Halogen and HID lamps. Power wiring attaches to brass screw terminals. Weight is virtually identical to previous PAR36 lamps. Assembly design includes clocking notch. They are lightweight, low-current and moisture resistant and provide stable light output for thousands of operating hours. The WAT PARMETHEUS PLUS  LED lights have a 40% brighter output than the original PARMETHEUS Series assemblies.

Product Features:

Offered in Landing and Taxi versions

Lightweight

STC-PMA

Direct replacement for outdated PAR36 Halogen and HID lamps

First commercially available PAR36 LED for Aviation applications

10.000 hour operating life

Polycarbonate, replaceable, hard-coated outer lens

Metal, heat dissipating coated housing

Whelen TIR™ (Total Internal Reflector) technology rivals strobe in intensity and effectiveness

Designed and manufactured in the USA.

Five year warranty

The CJ AVIATION Inc. is a manufacturer of  FAA-PMA approved fuel pumps for more than 20 years as direct replacements (*) for DUKES fuel pumps installed in Beechcraft, Cessna, Diamond, Maule, Mooney, Lake and Navion aircraft. They can be furnished as NEW or NEW EXCHANGE both priced the same except that for NEW pumps there is no core refund/credit. These pumps feature a rigid construction, tighter tolerance design, redesigned motor and longer seal life. They come with certification (FAA Form 8130-3 ) and a two-year warranty or 300 hours, whichever comes first.

In addition, OVERHAULED EXCHAGE (**) fuel pumps are also offered on respective OEM AIRBORNE, DUKES and WELDON models for use in general aviation and experimental aircraft. The overhauled pumps are serviced in accordance with FAA-approved process specification and certified. These pumps are listed under the respective OEM product presentations.

For additional information please contact us.

(*) When selecting a part for installation consult the appropriate aircraft maintenace manual, parts catalogue, or equipment list for approved data. 

(**) In the case of NEW EXCHANGE or OVERHAULED EXCHAGE pumps, these are offered in exchange of an existing customer owned unit (core) for a quick turn around. A refundable core charge is included in the selling price. This is refunded or credited towards future orders with us when a qualified core is returned and its condition is approved by CJ AVIATION within 60 days of the date of the purchase invoice.

B.A.S  Inc.is a supplier of certified (TSO'd ) aircraft safety belts & shoulder harnesses for an extensive range of light aircraft including different Cessna, Piper, Beechcraft, Luscombe and other aircraft models. Their products are manufactured by AM-SAFE Inc. especially for B.A.S.

B.A.S TSO'd rear lap belts and harnesses are offered in different versions including Lap Belts Only, Fixed 3 Point Harness, Inertia 3 point Harness and Y Fixed Harness. The following optional accessories can be ordered only as part of a respective order of a B.A.S  Shoulder Harness/Lap Belt System at additional cost. They need to be specified at the time of ordering.

Padded neck cuffs from a soft suede material to add comfort and prevent chaffing. Available in Black, Tan, and Grey colors. 

BAS seat belt protector sheaths made from hard plastic to help protect lap belts from possible damage due to seat tracks, articulating seats, and doors.

B.A.S TSO'd inertia reel 4 point shoulder harness/lap belt system (kit) is designed and STC'd as a retrofit assembly to replace current aircraft seatbelts. It can be installed in the 2 forward seating positions of the aircraft. Consists of an inertia reel mounted to the aircraft cabin roof above and behind each seat, a "Y" shaped shoulder harness, a lap belt with mating buckle and associated bracketry, all mounting hardware, installation instructions, and STC for both pilot and co pilot shoulder harness seatbelt systems. Standard color of belts is Black but they may also be ordered by special order in different available colors at additional cost upon request. Back seat belts in matching colors are also available by special order. Product Features:

Different kits available with Standard Buckle, Utility Buckle (recommended for float planes) or Rotary Buckle. 

Utility Buckle systems are less restrictive in panic egress and individual belts may be replaced if damaged.

Rotary Buckle systems feature a push button release to disconnect shoulder straps while keeping lap belts connected.

B.A.S Inertia Reel 4 Point Shoulder Harness/Lap Belt Systems are easy to use and comply with FAA-TSO-C114.

Optional Accessories available at additional cost. They can be ordered only as part of a respective order of a B.A.S  Shoulder Harness/Lap Belt System:

BAS Padded Neck Cuffs. Padded neck cuffs from a soft suede material to add comfort and prevent chaffing. Available in Black, Tan, and Grey colors. Please specify color at the time of ordering.

BAS Seat Belt Protector Sheaths. Protector sheaths are made from hard plastic to help protect lap belts from possible damage due to seat tracks, articulating seats, and doors.

Due to the many lengths, styles, and attach fittings available for B.A.S products, prices are indicative and per seat. In addition they must be special ordered and they are non-cancellable/non-returnable (NCNR) once the order is placed.

For more information please refer to the supplied documentation or contact us.

All aircraft fuel systems have filters and strainers to ensure that the fuel delivered to the engine(s) is free from contaminants. The first of these is encountered at the outlet of the fuel tank. A sump is used to encourage the collection of debris in the lowest part of the tank, which can then be drained off before flight. The actual tank outlet for the fuel is positioned above this sump. Some type of screen is used to trap contaminants attempting to flow out of the tank into the fuel system. Finger screens (strainers) are common on light aircraft. They effectively increase the area of the fuel tank outlet, allowing a large amount of debris to be trapped while still permitting fuel to flow. They are screwed into a fitting welded in the tank outlet.

Offered finger strainers are intended for use in fuel tank outlets. They are available in standard and lage sizes. Standard size features a brass fitting with 3/8" male pipe thread which fits AN867-3 welding flange, and 1/4" female pipe thread for valve or fuel line fitting. Screen is 16 mesh brass. Large finger strainer has a 3/8"-NPT x 1/2"-M-NPT brass bushing with a T304 stainless steel screen.

The Silicon Microstructures SM5882 series of OEM pressure sensorscombines state-of-the-art pressure sensor technology with CMOS mixed signal processing technology to produce an amplified, fully conditioned, multi-order pressure and temperature compensated sensor in a small SO16 plastic package. The model SM5882 is designed for operating pressure ranges at 0.6 PSI and 1.5 PSI. Typically used in medical instrumentation, pneumatic control, gas flow and HVAC applications. 

Product Features

CMOS digital signal processor technology

Calibrated pressure available through I²C-Bus-Interface

Analog output signal ratiometric with supply voltage

Differential pressure applications with +/- pressure

EEPROM stored individual correction data

SO-16 package for surface mount

For additional information please refer to the supplied documentation.

Military Specification MS35058 Series Toggle Switches can be used to upgrade your aircraft's cockpit controls. These heavy-duty metal switches have a standard shape that works well for a variety of applications can be used for most components that only function in either the on or off positions. They are available in several sizes to fit your particular airplane and are shipped with all necessary rings and hardware for installation. Toggle switches are available with two or three operating positions, 1 or 3 hole mounting and a variety of circuitry & electrical ratings. Contacts are made of solid silver. Wide usage is found in aircraft, mobile, marine, electronic and industrial applications. Available in full "AN" standard size & Ultra Miniature 1/2" size, contact types and circuit codes (see reference chart).

Elevate your aviation experience with Textron Aviation, your trusted source for top-tier aircraft batteries. CONCORDE® BATTERY CORPORATION, is a leader in high-quality lead-acid batteries, to power Cessna®, Beechcraft® and Hawker® aircraft. Their PLATINUM family of batteries offer superior engine starting performance, excellent charge acceptance, reliable essential power in the event of a generator failure, maintenance-free operation with no need for electrolyte or water addition, and advanced absorbed glass mat (AGM) separators.  CONCORDE® PLATINUM batteries are hazmat exempt and shipped fully charged and ready to install.

The  CONCORDE® RG® Series of premium hand made AGM aircraft batteries within the PLATINUM family are low resistance, valve regulated lead acid (VRLA) batteries providing excess power for many applications. The RG-25XC aircraft battery has the highest cranking power and capacity in the 25 Group.

SKY-TEC, a HARTZELL ENGINE TECHNOLOGIES brand, includes starters and support for Prestolite, Electrosystems, Lamar and Kelly designs. SKY-TEC OEM contactors are today installed in many general aviation aircraft while SKY-TEC FAA-PMA contractors can be used for starter, battery master/auxiliary or auxiliary power applications in replacement of OEM parts.

SKY-TEC STS-S Series FAA-PMA certified aircraft starter solenoids (aka relays) are intermittent duty suitable for starter applications. They are available in 12V (STS-S12) or 24V (STS-S24) versions. Activation: +V to S-Terminal (Frame is grounded by mounting).

SKY-TEC STS-M Series FAA-PMA approved Battery/Master solenoids are continuous duty solenoids intended for use in battery master/auxiliary applications in certified aircraft. They are available in 12V (STS-M12) or 24V (STS-M24) versions. Activation: -(Ground) to S-Terminal. (Floating ground frame).

SKY-TEC STS-A Series FAA-PMA approved solenoids are continuous duty and typically used for connecting auxiliary (ground) power. They are available in 12V (STS-A12) or 24V (STS-A24) versions. Activation: varies.

Product Features:

FAA-PMA Certified

All-metal case construction

Silver contacts (vs. copper) for high-current capability and long-life. They provide 300A in-rush capability. Much higher than the original units.

Strong spring and high-current coil for quick contact opening - minimizing arcing

Single coil terminal (other end connected to case)

High quality manufacturing 

Upgraded to perform best with today's lightweight, high torque starters

Same OE terminal layout simple to install

For additional information on different SKY-TEC series of slenoids and their applications in different aircraft please refer to the respective product presentations.

Versatile split red master switch used in virtually all single engine Cessna models since 1970. It can be used in most light aircraft with single alternator systems. Left rocker normally is used for alternator and right half for battery. Amp Rating: 20. The swich housing mount (P/N: S1843-1) is sold separately and can only be ordered together with the switch.

TIMKEN® lock nuts and respective lock washers are used in the mounting of straight bore bearings on shafts. They are available for bearings in the various series. Their dimensions relate to the bearing bore sizes.

Fuel and oil drain valves for use on Textron Aviation Cessna, Beechcraft and Hawker aircraft. Also available as FAA-PMA approved parts from other manufacturers.

LORD manufactures a range of vibration and motion control products for General Aviation aircraft including elastomeric and non-elastomeric mounts, full structures, yokes and attachments. Their Dynafocal engine mounts are available for many aircraft, including the most produced general aviation fixed wing aircraft models, such as the Cessna 152, Cessna 172, Cessna 182, Piper PA-28 series, and more. For additional information please also refer to the attached Lord Catalog.