MAGNUM aircraft rescue ballistic parachute systems (also known as  Vertical Launch Systems, VLS) are manufactured by STRATOS 07 S.R.O with knowledge and long experience in the construction of system components including rocket motors. They include different series produced for many years (like 450, 450 Speed, 501, 601) & newer certificated rescue systems like Magnum 1201 & 1401 for heavier aircraft and higher deployment speeds. They are intended for use in hang-gliding, paragliding, powered hang-gliding, powered paragliding,  unpowered and powered gliders,  gyroplanes as well as a wide range of two- and multi-seat airplanes and helicopters, including Light Sport, Experimental and Ultralights with a maximum 3,960 pounds gross weight, and deployment speeds of up to 199 MPH. Magnum Ballistic Parachutes come in sofpacks or canisters. Rescue systems packed in the softpack are usually installed inside of the aircraft. Rescue systems packed in a duralminium container are installed mostly outside of the aircraft.

Please refer to tables of specifications and notes below for the selection of a right rescue system.

Notes:

The max take-off weight of the aircraft MUST NOT EXCEED the max allowable load of the rescue system.

If the aircraft Vne exceeds the max limiting speed for the rescue system deployment, mounting of the system should be done so that the pilot is informed of this speed.

MAGNUM ballistic parachute systems  are packaged in two parcels (one containing the parachute and the second containing the rocket). Because of the rocket, Haz-Mat shipping is required.

Appearing prices of MAGNUM rescue systems DO NOT INCLUDE cords between parachute and fuselage which are SOLD SEPARATELY. During the order, the length of activating cord from parachute to fuselage must be indicated. Other parts and accessories are also available at additional cost.

 Automatic flight control systems (AFCS) are aircraft autopilot systems with many integrated features initially found only on high-performance aircraft but nowadays installed on modern aircraft of any size. Their capabilities vary from system to system with some AFCS offering advanced features beyond ordinary autopilot systems regarding programmability, the level of integration of navigational aids, the integration of flight director and autothrottle systems, and combining of the command elements of these various systems into a single integrated flight control human interface.

LEONARDO HELICOPTERS provides aircraft manufacturers with solutions ranging from single axis or secondary flight control computers and electronics to complete integration of flight control systems. The flight control system architecture spans from simplest architecture, lowest complexity up to full authority fly-bywire architecture, offering the following advantages:

• Compatibility with various actuation technologies (Hydraulics, Mechanical, Electro-Mechanical)

• Eased certification process (EASA Form 1 already achieved)

• Reduced integration cost and schedule risk (building blocks)

The Flight Control Systems (FCS), used to control the control surfaces of the aircraft, are based on:

• Flight Control Computer (FCC)

• APSW (Autopilot).

• Building blocks of dual, dual-duplex, triplex and quadruplex FCS architecture. 

Apart from new, LEONARDO older FCS are also offered in NEW SURPLUS or USED conditions (Serviceable or Overhauled). For additional information please consult the supplied documentation or contact us.

Integral fuel tanks in aircraft form part of their wing or fuselage structure and they are commonly met in high-performance aircraft as they are the lightest, with most space per unit of weight. Rigid removable aircraft fuel tanks are also used in some aircraft, typically made of stainless steel or aluminum alloy and riveted together. Flexible fuel tanks (aka fuel bladders) are fuel containers made of reinforced flexible materials. They share many characteristics with rigid tanks but they require a smaller opening in the aircraft to be installed. Also used in other sectors for rapid deployment of storage facilities or increase capacity of fuels (gasoline, diesel or jet fuel) but also for water, oils, or as emergency units. They are made of high-quality PVC, EVA, and TPU (Thermoplastic Polyurethane) coated fabrics, are fully UV resistant, and can operate at temperatures from -50°C to +90°C, ensuring durability and reliability under the most demanding conditions. Made by different manufacturers, these tanks conform to commercial standards while some of them are ballistic-tolerant or engineered for mission-critical military or aerospace uses, meeting respective commercial (such as TSO-C80 and 14 CFR Part 29) as well as military specifications like MIL-DTL-6396, MIL-DTL-5578, and MIL-DTL-27422.

Related materials such as tank cleaners/degreasers, adhesives & sealants are also offered and included in this presentation. 

Tank adhesives/sealants come in different compounds (chemical composition) and respective prices, and their selection heavily depends the material of the tank they shall be applied and the sealing content (water, oil, fuel, etc). The selection and use of any sealant during tank construction, maintenance or repair should always ensure sealant's compatibility with tank composition and chemical resistance to fuels or other fluids to be sealed. Commonly used sealants for tanks span from PVC, the more cost-effective but with low temperature resistance & toxic when burned, to more expensive but safer Silicone ones, with excellent flexibility, high and low-temperature resistance and biocompatibility, to Polyurethane sealants, durable but not so chemically resistant as Polysulfide, and Polysulfide rubber sealants, flexible, and extremely resistant to gasoline, ethanol and many other chemicals. 

For aircraft integral fuel tanks and rigid removable fuel tanks made of metals, two-part Polysulfide sealants are often the preferred choice. For flexible Polyurethane/Thermoplastic Polyurethane (PU/TPU) fuel tanks (bladders) the bonding/sealing material itself is often a specialized PU/TPU formulation for enhanced flexibility and durability,chemical resistance to hydrocarbon fuels, solvents, and oils, impact resistance, and bonding strength compared to traditional formulations. Silicone sealants are also used depending on application requirements.

Supplied either as OEM parts or as parts of our own labelled (AVIATIONEU NEW ERA) product lines. 

In 1971 AURORA BEARING COMPANY entered the rod end and spherical bearing market and soon became a major force in the rod end industry. The AURORA BEARING product potfolio today includes both Aerospace / Military and Commercial / Industrial rod ends and standard spherical bearings in inch and metric systems while special bearings can be designed and manufactured on request. Different series of these bearings are separately presented together with respective documentation.

AURORA BEARING MM & MB Series include Precision General Purpose Male Rod Ends with the following features. Rod ends in these series are equivalent to RBC® HEIM® BEARINGS part numbers shown in the parenthesis.

Body - Low carbon steel, protective coated for corrosion resistance. Size 16 standard series body is alloy steel not heat treated.

Ball - Alloy steel, heat treated, hard chrome plated.

Race - Low carbon steel, protective coated for corrosion resistance.

Grease Fitting -  supplied without grease fittings. When a grease fitting is required, specify by adding suffix "Z" or "F". Ex.: MM-6Z = Zerk Type Fitting MM-6F = Flush Type Fitting.

Load ratings apply only to rod ends without grease fittings.

PTFE Liners available upon request. Specify by adding suffix "T". Ex.: MM-6T.

The PARKER AIRBORNE designs and manufactures motor driven fuel fuel  boost and transfer pumps and is part of the PARKER AEROSPACE GROUP of the PARKER HANNIFIN CORPORATION. These pumps consist standard equipment by the world's leading airframe manufacturers. The PARKER AIRBORNE product range includes:

- In Line fuel pumps for low-flow fuel applications,

- Submerged Centrifugal fuel pumps,

- High Performance Centrifugal fuel pumps for use in turboprop or turbofan jet aircraft,

- Submerged Duplex fuel pumps with two distinct pumping elements

The PARKER AIRBORNE fuel boost pumps use 28 V direct current (DC) to drive a highly efficiency, brushless DC (BLDC) motor or 115.5 V alternating current (AC) three-phase induction motors. The BLDCmotor-driven pumps incorporate integral electronic controllers using Hall Effect sensor rotor-position feedback. The hardware-only controller doe not use any software or programmable logic devices. These pumps feature:

-fuel cooled motor and electronics

-fuel wetted carbon bearings allowing for long-life fluid film design with no rotating shaft seals

-a high efficiency brushless DC (BLDC) motor or a three-phase induction motor

-qualification for high levels of lighting and electromagnetic interference (EMI).

The PARKER AIRBORNE fuel boost pumps can be furnished as either NEW, NEW EXCHANGE or OVERHAUL EXCHANGE. 

Offered pumps in OVERHAUL Condition are supplied in accordance with FAA-approved process specification, come with a FAA Form 8130-3 and can be provided in exchange of existing customer owned units (cores). In all EXCHANGE cases,  the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders with us when our co-operating supplier verifies that the unit is in a reasonable condition. For additional information please consult the supplied documentation (*) or contact us.

In addition to the PARKER AIRBORNE pumps, RAPCO FAA-PMA approved pumps are also offered as direct replacements  to the respective PARKER AIRBORNE models. The RAPCO replacement pumps can be furnished as either NEW EXCHANGE or OVERHAUL EXCHANGE (please refer to their separate product presentation).

(*) The supplied documentation is to be used for reference only. When selecting a part for installation consult the appropriate aircraft maintenance manual, parts catalogue, or equipment list for approved data.

The ACS unvented flush fuel cap operates with a lift and turn lever. This cap has a 3" opening for easy refueling. Cap & adapter ring are anodized "clear" for corrosion resistance. Cap is fastened to adapter ring with safety chain.

FILLER NECK offers a variety of cap neck styles and materials which can support oil, fuel, hydraulic or water applications. Accessory options can be used to build the filler assembly you need. Three different strainers provide varying degrees of filtration for 300 Series caps and necks to help maintain clean fluids within the engine system. Special mountings match the type of connections required.

YAESU rechargable batteries are intended for use with YAESU handheld transceivers.

Since its introduction in 1994, the B&C SPECIALITY PRODUCTS BC320 Starter for Continental engines has established an impressive service record as the ONLY starter design on the market that has provided reliable, long-term service for these engines. 

Suitable for installation on Continental engines (C-75, C-85, C-90, C-145-2, O-200, IO-240, O-300-A, -B, and -C, and GO-300-A, -B, and -C) it solves all the problems that other starter designs have had:  worn-out clutches, broken pinions, nagging oil leaks, and catastrophic failure modes. Featuring the durability of all-steel gears and heavy-duty ball-bearings, and the efficiency of a high-torque series-wound motor, it provides greater starting torque, while saving 4.3 to 5.2 lbs. over the old key-type and pull-cable type starters (respectively).

The B&C SPECIALITY PRODUCTS BC320 Starter is STC-PMA approved for use in certificated aircraft, and is available with or without the STC (*). Two installation kits are also available:  one for replacing a key-type starter (Installation Kit 501-1), the other for replacing a pull-cable type starter (Installation Kit 501-3). For key-type starters, before installing the BC320, you will need to remove the needle bearing pressed into the engine case & install the supplied plug in its place. For pull-cable starters, before installing the BC320, you will need to cut off the 9/16 steel shaft that is installed in your engine case.

Other versions of BC320 Starter for 12v and 24v electrical systems (BC320-2, 12v Counter-Rotating or the 24v BC320-3) are also available.

(*) For the issue of the STC, the aircraft make and model, aircraft registration and serial number are required.

Oval shaped copper sleeves used in making eye or lap splices in flexible cable. Sleeves are slipped over the two strands of cable to be fastened and are then compressed with special Nicropress hand squeezers. Provides a bond that is even stronger than a standard splice. They are offered in pure copper or zinc/tin coated for different cable sizes in inches. Plain copper ("18" series) and zinc coated sleeves ("28" series) are used with galvanized cable, and tin coated sleeves are to be used with stainless steel cable. 

TIMKEN® lock nuts and respective lock washers are used in the mounting of straight bore bearings on shafts. They are available for bearings in the various series. Their dimensions relate to the bearing bore sizes.

Aviation grade ELECTRODELTA X61 series solenoids by LAMAR TECHNOLOGIES LLC are offered in continuous  or intermitant duty in 12 or 24 Volt. They fit current GA production aircraft as well as legacy aircraft and replace both single terminal switched units, as well as the current double terminal switched units in production today. All units have multiple quality and functional tests prior to certification and delivery. Non FAA-PMA Approved.

Product Features:

Replace most contactors in general aviation

Available in 12 or 24 Volt

Available for Continuous or Intermittent duty

All units inspected and tested to performance standards

Warranty 24 months

OMRON A16 series pushbutton 16-dia. cylindrical body switches are detachable switches. The same contacts can be used for both standard loads and microloads. Their miniature design of 28.5 mm makes these switches the smallest class in the industry. Easy-to-wire terminal arrangement. Certified for EN 60947-5-1. These switches are offered in lighted and non lighted versions, different colors, display shapes, with LED or incandescent lamps and different socket units. Please consult the attached documentation for ordering.

ELECTRODELTA is the world market leader in top quality voltage regulators for general aviation aircraft, and continues to revolutionize the industry with proven technologies and improvements. The units are assembled from the highest quality electronic components available and are meticulously tested and calibrated to ensure maximum performance. The ELECTRODELTA product line was acquired in October 2012 by LAMAR TECHNOLOGIES LLC. 

ELECTRODELTA VR Series voltage regulators are offered in 14 and 28 Volt models with FAA/PMA or TSO certifications and are suitable as replacements for use in aircrafts of different manufacturers.

McFARLANE® AVIATION MC0543022-2 Series FAA-PMA approved nose wheel steering rods s are intended for use on for Cessna 172 series aircraft replacing respective OEM steering rod,tube assemblies.They feature new re-designed long-life springs, hardened internal washer for greater durability, stainless steel tubes for improved corrosion resistance  and optimum performance even after years of service.

Cessna Models' Application List:

172D,E,F,G,H,I,K,L,M,P

P172,

R172K

F172D,E,F,G,H,K,L,M,N,P

FP172

FR172E,F,G,H,J,K

172R

172S

AS81820 Standard bearings are Plain Self-Aligning, Self-Lubricating ,Low Speed bearings with a -65 TO +325 °F temperature operating range offered in different specifications with those of SAE AS Standard superseding the Military Standard  respective parts.  AS81820 Standard bearings include AS14101/MS14101 narrow, grooved race, AS14102/MS14102 wide, chamfered race, AS14103/MS14103 wide, grooved race, and AS14104/MS14104 narrow, chamfered race.

AS14101/MS14101 and AS14104/MS14104 bearings included in this presentation are offered as OEM parts by different manufacturers including RBC® BEARINGS, NEW HAMPSHIRE BALL BEARINGS® (NHBB), AURORA BEARING COMPANY® and others as well as their replacements by NATIONAL PRECISION BEARING® (NPB).

SAE-AS14102 and SAE-AS14103 (separately listed) supersede those of MS14102 and MS14103 specifications. They are both are wide plain spherical bearings, self lubricating self aligning, and low speed, designed for operation in high temperature environments  (-65°F to +325°F  or -53.9°C to +162.8°C). Their inner and outer rings are made from Corrosion Resistant Steel (CRES). AS14102/MS14102 series bearings come with a chamfered outer ring while those of AS14103/MS14103 series come with a grooved outer ring. They are offered as either OEM parts from RBC® BEARINGS or as part of our separately listed own label (AVIATIONEU NEW ERA) product lines sourced from quality manufacturers. 

For more information please refer to the Product Description section and other supplied documentation.

The ORION 600 series is a FAA/TSO approved all LED self-contained wingtip mounted position (aviation red/green) / anti-collision (aviation white) lighting system manufactured by WHELEN AEROSPACE TECHNOLOGIES (WAT). Incorporating the latest state of the art LED technology available in an all-inclusive package, the ORION 600 series system eliminates the need for external flasher boxes, external power supplies and reduces current draw providing thousands of hours of operation. Flush mountable for a wide variety of applications with minimal integration and easily retrofitable to the Whelen legacy strobe products. The ORION 600 series is quite simply the brightest form of LED Anti-collision and Position lighting available. Offered in 12 VDC and 28 VDC versions.

Product Features:

Fully FAA/TSO-C96a & TSO-C30c approved

FAR SPEC Certified

Replaceable hard coated polycarbonate lens to maintain maximum light output

No RF emissions

Aerodynamic design without sacrificing light output

Exceeds FAA minimum intensity requirements for maximum visibility and increased safety of flight

Environmentally tested and certified to RTCA/DO-160G standards

Product Specifications:

Weight 0.4 lbs.(181gm)

Dimensions H x W x L 2.04” (52mm) x 1.78” (45mm) x 5.65” (144mm)

Volts 12 VDC 28 VDC

Position LED colors Aviation Red Aviation Green

Anti-Collision LED color Aviation White

Lenses Clear Polycarbonate Hardcoat, Field Replaceable

RBC NICE 5000 Series bearings are similar in construction to those of 400 Series except that they have a flange on the outer ring to locate the bearing when pressed into a tube or housing, thus eliminating the need for an external mounting device. Designed for moderate loads and speeds (not exceeding 1200 rpm) where running accuracy and noise level requirements do not warrant the more expensive precision ground bearings. They feature a full ball complement without a retainer. The rings are case hardened and the soft steel band on the outer ring of the unitized assembly allows the bearing to be pressed into a housing without the necessity of close housing tolerances. The bearings are supplied pre-greased as a standard. 

NICE 5000 Series Specifications (See chart )

Bellcrank bearings are commonly used for various control bellcranks throughout many experimental aircraft. They are prepacked with lubricant conforming to Mil. -G23827, inspected per Mil. I 45208A and 100% traceable. Operating temperature range -30 Deg. F to +250 Deg. F