CONCENTRIC HE Series AC/DC power packs allows the selection from a broad range of standard components to design a power system to meet the exact specifications of applications, both vertical and horizontal, with a full range of valving, motor, pump and reservoir combinations and minimum inventory for maximum cost efficiency. Other advantages of the HE power packs includes low power consumption, quiet operation, proven field performance and long service life. Concentric HE2000 Series AC/DC Power HPUs  can be coupled via suitable hydraulic lines to a wide range of operating mechanisms. They normally operate hydraulic cylinders, but can be used with any other hydraulic actuating device. A unit can individually control up to four (4) hydraulic cylinders.

Product Features:

All units have:

12 or 24 VDC motors

Adjustable internal relief valve preset at factory

Load holding check valve

Reservoirs plumbed for horizontal / vertical mount

Various size cylindrical/rectangular reservoirs

9/16˝-18 SAE outlet and return ports (P/N 1303835 1/4˝-18 NPTF ports)

140 x 170 mesh inlet strainer

Please refer to the attached documentation for specifications & additional information.

Clip-Locking Turnbuckles utilize 2 locking clips instead of lock-wire for safety. The turnbuckle barrel and terminals are slotted lengthwise to accommodate the locking clips. After the proper cable tension is reached the barrel slots are aligned with the terminal slots and the clips are inserted. The curved ends of the locking clips expand and latch in the vertical slot in the center of the barrel. They are available for different cable diameters and thread sizes in inches covering desired minimum breaking strength requirements.

Different turnbuckle components listed below are used in turnbuckle assemblies. They are sold separately to meet application requirements. Please refer to the attached documentation.

MS21251 Series Barrels (superceding those of AN155 series)

MS21252  Series Fork Ends (superceding those of AN161 series)

MS21254 Series Pin Eye Ends (superceding those of AN165 series)

MS21255 Series Cable Eyes (superceding those of AN170)

MS21260 Series Cable Swage Ends (superceding those of AN669)

MS21256 Series Clips

The FIRST letters "R" or "L" following the dash number designate a RIGHT HAND THREAD or LEFT HAND THREAD respectively.

The SECOND letters "S" or "L" following the dash number indicate a SHORT LENGTH or LONG LENGTH respectively.

OMRON A16 series pushbutton 16-dia. cylindrical body switches are detachable switches. The same contacts can be used for both standard loads and microloads. Their miniature design of 28.5 mm makes these switches the smallest class in the industry. Easy-to-wire terminal arrangement. Certified for EN 60947-5-1. These switches are offered in lighted and non lighted versions, different colors, display shapes, with LED or incandescent lamps and different socket units. Please consult the attached documentation for ordering.

B.A.S  Inc.is a supplier of certified (TSO'd ) aircraft safety belts & shoulder harnesses for an extensive range of light aircraft including different Cessna, Piper, Beechcraft, Luscombe and other aircraft models. Their products are manufactured by AM-SAFE Inc. especially for B.A.S.

B.A.S TSO'd rear lap belts and harnesses are offered in different versions including Lap Belts Only, Fixed 3 Point Harness, Inertia 3 point Harness and Y Fixed Harness. The following optional accessories can be ordered only as part of a respective order of a B.A.S  Shoulder Harness/Lap Belt System at additional cost. They need to be specified at the time of ordering.

Padded neck cuffs from a soft suede material to add comfort and prevent chaffing. Available in Black, Tan, and Grey colors. 

BAS seat belt protector sheaths made from hard plastic to help protect lap belts from possible damage due to seat tracks, articulating seats, and doors.

B.A.S TSO'd inertia reel 4 point shoulder harness/lap belt system (kit) is designed and STC'd as a retrofit assembly to replace current aircraft seatbelts. It can be installed in the 2 forward seating positions of the aircraft. Consists of an inertia reel mounted to the aircraft cabin roof above and behind each seat, a "Y" shaped shoulder harness, a lap belt with mating buckle and associated bracketry, all mounting hardware, installation instructions, and STC for both pilot and co pilot shoulder harness seatbelt systems. Standard color of belts is Black but they may also be ordered by special order in different available colors at additional cost upon request. Back seat belts in matching colors are also available by special order. Product Features:

Different kits available with Standard Buckle, Utility Buckle (recommended for float planes) or Rotary Buckle. 

Utility Buckle systems are less restrictive in panic egress and individual belts may be replaced if damaged.

Rotary Buckle systems feature a push button release to disconnect shoulder straps while keeping lap belts connected.

B.A.S Inertia Reel 4 Point Shoulder Harness/Lap Belt Systems are easy to use and comply with FAA-TSO-C114.

Optional Accessories available at additional cost. They can be ordered only as part of a respective order of a B.A.S  Shoulder Harness/Lap Belt System:

BAS Padded Neck Cuffs. Padded neck cuffs from a soft suede material to add comfort and prevent chaffing. Available in Black, Tan, and Grey colors. Please specify color at the time of ordering.

BAS Seat Belt Protector Sheaths. Protector sheaths are made from hard plastic to help protect lap belts from possible damage due to seat tracks, articulating seats, and doors.

Due to the many lengths, styles, and attach fittings available for B.A.S products, prices are indicative and per seat. In addition they must be special ordered and they are non-cancellable/non-returnable (NCNR) once the order is placed.

For more information please refer to the supplied documentation or contact us.

RBC Aerospace Bearings offers a full line of Mil Spec standard lined journal bearings, unlined bushings, and many specialty and custom designed products to support the aerospace industry.   Journals are designed in a straight (plain) configuration with a flange to accommodate a combination of radial and axial loads with corrosion resistant materials and coatings. Journals are also offered in high temperature and water resistant series. Typical journal materials are CRES 17-4PH and aluminum.  Bearings may also be cadmium or zinc nickel plated as required while CRES 440C and Inconel® 718 are available upon request. Journal bore and flanged journal face surfaces may also be provided with various liner systems to satisfy specific application requirements. Machinable liners  are qualified to AS81934 (formerly MIL-B-81934). For additional information please refer to the attached documentation.

ACS PRODUCTS is a supplier of quality parts and accessories to the aircraft industry while many of their products are also used in a wide variety of other fields including marine, recreational vehicles, and industrial applications. Their product lines include cable assemblies, ignition switches as well as machined and custom products.

ACS Pitot / Pitot Static Tubes include different models. Model 15144 'L' shaped, aluminum pitot heads are simple, inexpensive, good-quality suitable for homebuilts. They are available either as pitot only or pitot static. Both have flange mounting to aid underwing fitting. 

RBC Aerospace Bearings offers the industry’s widest selection of rod end type bearings (also known as the Heim rod ends or joints) in inch and metric sizes with a variety of platings, coatings and materials and a range of optional features such as lubrication fittings, left hand threads and keyway slots. RBC product range of Heim rod ends are offered with brass race inserts in standard, precision and high capacity designs, high strength two piece designs, self-lubricating rod ends with engineered thermoplastic races or high performance Teflon® liners, military standard (AS81935) ME/FE rod end series, ball bearing rod ends with extremely low friction and misalignment capability and elastomeric bearing rod ends that reduce vibration and noise in installations. Please refer to the attached documentation for additional information.

M81935/1 ME Series Product Features:

Wide, High Capacity Series

External Threads

Alloy Steel, Self-Lubricated

Electrodelta (Hartzell Engine Technologies) is the world market leader in top quality voltage regulators for general aviation aircraft, and continues to revolutionize the industry with proven technologies and improvements. The units are assembled from the highest quality electronic components available and are meticulously tested and calibrated to ensure maximum performance.The Electrodelta product line was acquired by by Lamar Technologies LLC in order to add new and alternative  parts to the company's product lines.

SKY-TEC, a HARTZELL ENGINE TECHNOLOGIES brand, includes starters and support for Prestolite, Electrosystems, Lamar and Kelly designs. SKY-TEC OEM contactors are today installed in many general aviation aircraft while SKY-TEC FAA-PMA contractors can be used for starter, battery master/auxiliary or auxiliary power applications in replacement of OEM parts.

SKY-TEC STS-S Series FAA-PMA certified aircraft starter solenoids (aka relays) are intermittent duty suitable for starter applications. They are available in 12V (STS-S12) or 24V (STS-S24) versions. Activation: +V to S-Terminal (Frame is grounded by mounting).

SKY-TEC STS-M Series FAA-PMA approved Battery/Master solenoids are continuous duty solenoids intended for use in battery master/auxiliary applications in certified aircraft. They are available in 12V (STS-M12) or 24V (STS-M24) versions. Activation: -(Ground) to S-Terminal. (Floating ground frame).

SKY-TEC STS-A Series FAA-PMA approved solenoids are continuous duty and typically used for connecting auxiliary (ground) power. They are available in 12V (STS-A12) or 24V (STS-A24) versions. Activation: varies.

Product Features:

FAA-PMA Certified

All-metal case construction

Silver contacts (vs. copper) for high-current capability and long-life. They provide 300A in-rush capability. Much higher than the original units.

Strong spring and high-current coil for quick contact opening - minimizing arcing

Single coil terminal (other end connected to case)

High quality manufacturing 

Upgraded to perform best with today's lightweight, high torque starters

Same OE terminal layout simple to install

For additional information on different SKY-TEC series of slenoids and their applications in different aircraft please refer to the respective product presentations.

The EATON AEROQUIP FC300 are AQP elastomer hoses with a blue, abrasion-resistant fabric cover with single wire braid reinforcement over a synthetic rubber inner tube for longer life. The FC300 hoses are designed for high pressure fluid applications such as power steering, hydraulics, air, fuel, lubricating oils, fire resistant hydraulic fluids and other industrial fluids. They are also suitable for biodiesel use up to B20 and max temperature of 212°F (100°C). Available in different internal diameters in inches and for use in different maximum operating pressures (psi). Priced and sold by the foot.

Indicative Applications:

Power steering lines

Hydraulics

Air

Gasoline

Fuel

Lubricating oils

Over the wall air tool

Dot-approved air brake

Max operating pressure is 2250 psi

Operating Temperature Range

-55°F to +302°F (-49°C to +150°C)

Air not to exceed +250°F [+121°C]

Notes: 

(1) The FC300 Hose only works with FC300 steel fittings (to be ordered separately). Easily assembles with a bench vise and/or wrenches.

(2) FC300-32 and FC300-40 hoses DO NOT meet SAE 100R5 pressure with reusable fittings. FC300-32 is rated to 350 psi with crimp fittings. 

LORD manufactures a range of vibration and motion control products for General Aviation aircraft including elastomeric and non-elastomeric mounts, full structures, yokes and attachments. Their Dynafocal engine mounts are available for many aircraft, including the most produced general aviation fixed wing aircraft models, such as the Cessna 152, Cessna 172, Cessna 182, Piper PA-28 series, and more. For additional information please also refer to the attached Lord Catalog.

SUPERIOR PANEL TECHNOLOGY (SPT) has developed a brighter, more uniform and longer lasting glare shield lighting system. The 18” x 1” glow strip electroluminescent lamps provide a beautiful fluorescent-like aviation green or a white light output. The ultra-thin lamps (.065 including the adhesive backing) are very flexible and conform to the curves of the underside of the glare shield. The SPT Glow Strips meet the FAA 23.853 burn test. Inverters are included with the kit. They are offered with or without a dimmer. The recommended dimmer for the strips is the Pulse Width Modulating (PWM) dimmer by SPT. Optional 14V or 28V battery back-up systems are available and recommended. SPT offers LIFETIME warranty on the Glow Strip lamps and 5-year warranty on the PWM dimmers.

SUPERIOR PANEL TECHNOLOGY (SPT) Glow Strip Product Range:

Green

GS1-18-14G Single Glow Strip-14V

GS2-36-14G Two lamp Glow Strip-14V

GS2-36-28G Two lamp Glow Strip-28V

Green with PWM Dimmer without off switch on dimmer 

GS1-18-14GPWM Single Glow Strip-14V

GS2-36-14GPWM Two lamp Glow Strip-14V

GS2-36-28GPWM Two Lamp Glow Strip-28V

Green with PWM Dimmer with off switch on dimmer  

GS1-18-14GPWMS Single Glow Strip-14V

GS2-36-14GPWMS Two lamp Glow Strip-14V

GS2-36-28GPWMS Two Lamp Glow Strip-28V

White

GS1-18-14W Single Glow Strip-14V

GS2-36-14W Two lamp Glow Strip-14V

GS2-36-28W Two lamp Glow Strip-28V

White without off switch on dimmer

GS1-18-14WPWM Single Glow Strip-14V

GS2-36-14WPWM Two lamp Glow Strip-14V

GS2-36-28WPWM Two Lamp Glow Strip-28V

White with off switch on dimmer

GS1-18-14WPWMS Single Glow Strip-14V

GS2-36-14WPWMS Two lamp Glow Strip-14V

GS2-36-28WPWMS Two Lamp Glow Strip-28V

Battery Back-Up

BP14V Battery-Back Up 14V

BP28V Battery-Back Up 28V

In 1971 AURORA BEARING COMPANY entered the rod end and spherical bearing market and soon became a major force in the rod end industry. The AURORA BEARING product potfolio today includes both Aerospace / Military and Commercial / Industrial rod ends and standard spherical bearings in inch and metric systems while special bearings can be designed and manufactured on request. Different series of these bearings are separately presented together with respective documentation.

AURORA BEARING MW & MG Series include Precision General Purpose Female Rod Ends with the following features. Rod ends in these series are equivalent to RBC® HEIM® BEARINGS part numbers shown in the parenthesis.

Body - Low carbon steel, protective coated for corrosion resistance. Size 16 standard series body is alloy steel not heat treated.

Ball - Alloy steel, heat treated, hard chrome plated.

Race - Low carbon steel, protective coated for corrosion resistance.

Left-hand threaded units have an identification groove near end of shank.

Grease Fitting available for sizes -3 and up. Units are supplied without grease fittings. When a grease fitting is required, specify by adding suffix "Z" or "F". Ex.: MW-6Z = Zerk Type Fitting MW-6F = Flush Type Fitting.

Load ratings apply only to rod ends without grease fittings.

Studded configuration available upon request. Specify by adding suffix "S". Ex.: MW-8S.

PTFE Liners available upon request. Specify by adding suffix "T". Ex.: MW-8T.

TOST Flugzeuggerätebau designs and manufactures top quality products including aircraft wheels, brakes, tires, tubes, glider towing and launching equipment and tow releases serving the needs of aviation sports and industry. TOST and TOST AERO brands for tires are synonyms for safety in aviation. 

For more than 30 years TOST has manufactured aircraft tires from 3" to 10" exclusively under the TOST AERO brand with a long lifetime, robustness and capability for high loads and speeds. TOST AERO tires and tires from other brands can be used with TOST wheels designed to cover a wide range of applications in gliders, motor gliders, aircraft, ultralight, amphibium aircraft, helicopters and gyrocopters but also in heavy-duty applications. Matching tire tubes with different valves and valve extensions are also offered by TOST to cover application requirements.

For additional information please refer to the supplied documentation.

BC207 High/Low Voltage Warning Indicator by B&C SPECIALITY PRODUCTS  is a solid-state device which provides a visual indication of abnormal bus voltage via a panel-mounted warning light (included). It is intended for use in non certified aircraft. Not FAA Approved. When flashing,the warning light indicates a bus voltage greater than 15.5 volts D.C. When steady, it indicates a bus voltage below 12.5 volts D.C. The product also includes B&C S708-2 Miniature Push-Button switch (push-to-test). The BC207  Voltage Warning Indicator can be used in both 14v and 28v electrical systems. 

Standard single universal joints from CURTIS UNIVERSAL JOINT operate through angles of 35 degrees. For applications requiring greater angles, special design can be employed, enabling the joint to operate at angles up to 45 degrees. Joint is permanently assembled with small bearing pin riveted in place.

Product Specifications (see Chart)

The SPRL fuel locking and non-locking caps have secure sealing and easy finger tip operation. These caps are made from the highest quality modern engineering plastics with Viton o ring seals (which can be easily replaced). The mounting rings are anodized aluminum with the flange recessed to give a perfect flush fit whether it is riveted under a metal skin, as in the RV series, or built into a composite structure. The SPRL caps are non vented and recommended to keep the fuel in, the water out and in the locking version, other unwanted items out of your tank. 

SPRL-L (locking) and SPRL-S (non-locking) fuel  caps have an 65 mm O.D. and can be used on Europa, Compair, Glasair, Lancair, Murphy, OMF, Rocket, Velocity, Zenith and many more experimental aircraft. Wt: 80 grams.