GARMIN® GTX™ transponder product line includes Mode A/C and Mode S TSO'd panel mounted transponders offered in a‭ ‬wide variety of configurations to choose‭ ‬from‭, ‬depending on desired functions‭.‬ Different models are listed under separate product presentations. 

GARMIN® GTX™ 330 is a panel-mounted IFR-certified 250 W, Mode S digital transponder with traffic datalink capability and dedicated pushbutton keys for squawk code selection. The GTX™ 330 series brings ATC aircraft surveillance to new levels of precision, reliability and performance. Optionally available with 1090 MHz extended squitter transmission, certified to TSO-C166b authorization, the GTX™ 330 ES (Extended Squitter) provides an affordable pathway to ADS-B compliance for the Next Generation airspace system. The extended squitter technology enables transponders to automatically transmit traffic surveillance data (including aircraft flight ID, position, altitude, velocity, climb/descent, and heading information) compared to traditional Mode S and Mode C transponders, which can only broadcast altitude, and thus require a ground-based radar to correlate and identify the aircraft's position. In addition, simultaneous broadcast of this information to TAS or TCAS equipped aircraft, enables them to essentially see the same traffic picture for their location that ATC is watching on the ground. The ‬“ES” upgrade provides a ADS-B‭ ‬Out‭ solution but an input from an approved position source is still needed as GTX™ 330 does not have a WAAS GPS.

GARMIN® GTX™ 330 is discontinued and replaced by GTX™ 335, an entry-level ADS-B Out model‭ with a version integrating an  internal WAAS GPS. If ADS-B‭ ‬In capability is required then the the GTX™ 345 transponder should be selected.

For additional information please refer to the Product Description section.

WULTRAD INC. is a manufacturer of non-certified flight and engine instruments under FALCON GAUGE brand for experimental and homebuilt aircraft. Although their products are Non-TSO, they are made to TSO or MIL specifications for quality. 

FALCON GAUGE  Electrical Turn Coordinator is used for displaying the angular rate and sideslip of turning in horizontal flying and turning. The inclinometer indicates the slip angle of the aircraft while in a turn. A power failure flag drops into view whenever the voltage drops below a level for proper operation. The Turn Coordinator incorporates a built-in voltage regulator so it can be used with either 14VDC or 28VDC power system. It is compact in size and light weight eliminating radio interference.

This small, lightweight unlighted turn coordinator is excellent for homebuilt aircraft. Works for 14 Volt or 28 Volt systems. Features, power out warning flag with a 0° Panel. Fits Standard 3-1/8" Cut Out, 3-3/4" long.

The new OROLIA-KANNAD INTEGRA 406 GPS ELT is a major step forward in the development of ELT technology and aircraft safety. Major benefits over standard ELTs include  a fail-safe automatically activated system for transmission of both the unique identification and GPS position in case of ditching of the aircraft or a crash landing as well as the ability for the pilot/ crew to remove the ELT from a downed aircraft. In addition,it features internal 406MHz and GPS antennas saving significant cost on aircraft  installation without the need for an  external antenna (national authorities’ rules and regulations permitting) and additional external GPS interface.

The 406 INTEGRA fixed ELT(AF) transmits on both the international 406MHz satellite search and rescue system (min  24 hours from activation) and on 121.5MHz for local direction finding. Minimum operating temperature is -20°C. The internal battery life of the INTEGRA is 6 years. Complies with European and FAA standards.

406 INTEGRA ELT(AF) is designed for flat installation on fixed wing aircraft and can be connected to an outside antenna (sold separately). 

This ELT comes with:

the COMPACT universal mounting bracket

RC200 remote control panel

DIN-12 connector

SUB-D 9 pts female connector

Note: Hazardous Material

KANARDIA AETOS Basic EFIS Kit is a Non Certified complete navigation, flight and engine system for the ultralight airplanes, autogyros and helicopters. This self-contained state-of-the-art EFIS instrument is optimized for ultralight aircraft.

The AETOS Basic EFIS Kit comes with a large 7" sunlight-readable display with high contrast and integrated AHRS and GPS unit (AIRU), engine monitoring unit (DAQU), OAT probe, GPS antenna, cables & accessories. Engine sensors are not included in this kit. In contrast to NESIS EFIS, AETOS EFIS does not support flight maps. Options are available at additional cost to increase the functionality of this device.

ETSO'd Slimline Panel Mounted 10 W VHF Radio with built in 2-place intercom with auxiliary inputs for stereo music and audio warnings. Available with 8.33 kHz or  25kHz frequency spacing options.

Lightweight, FAA-PMA approved compact power supply unit from WHELEN AEROSPACE TECHNOLOGIES (WAT) for installation in the wingtips and tail of the aircraft, eliminating long runs of high voltage interconnecting cables. Only an 18 gauge low voltage wire supplies power to each power supply and between wingtip mounted power supplies and switch. This system is not synchronized. Flashes 50 times per minute (comet flash).

Product Specifications:

Wt. 1.2 lbs.

Size: 5"L x 3"W x 3.06" H.

Current 1.7A -14V, 0.85A - 28V.

FAA-PMA Approved.

This 2-1/4 inch flap indicator uses a resistance potentiometer as a flap position sensor. Transmitter is required. Wt: 9.8 oz.

The AVIASPORT indicators (gauges) are reliable, accurate and solid, combining the accumulated experience of more than twenty years with the latest technology  They have been designed for ROTAX engines and their display areas are divided into red, green and yellow zones in line with Rotax limits. They use a pointer that turns 240º or 320º, providing high resolution. AVIASPORT range of gauges includes CHT, EGT, tachometers, oil and fuel pressure, oil and coolant temperature, fuel level, voltmeters & ammeters and offered with casings of different sizes: 80mm; 57mm and 52mm.

AVIASPORT Oil Pressure indicators (gauges) are designed specifically for ROTAX 912/914 aircraft engines with painted red, green, and yellow gauge markings. are available in two sizes: 52 and 57 mm. They are offered in two unit versions for readings in PSI or Bars. They work with different pressure sensors depending on these installed in ROTAX 912/914 engines: the VDO sensor (Before September 2008) or the 4..20mA sensor (after 2008).

UMA Electronic Hydraulic Pressure Gauges are offered in TSO'd and Non TSO'd models and 1-1/4"  or 2-1/4" diameters to fit respective aircraft panel openings. They are housed in aluminium or Valox 420 plastic cases (depending on the model) and connect to  precision, high pressure transducers which mount directly to the aircraft's hydraulic system. Standard markings are black and white. Recommended for new design projects and applications. 

Note: Pressure Transducers (Senders) ARE NOT INCLUDED in the prices of the pressure gauges. They are sold separately and are not TSO'd.

The HONEYWELL BENDIX KING® KCS 55A Compass System provides the pilot with a simple, comprehensive visual display of the aircraft's heading and position in relation to a desired course. The system simplifies course orientation, intercept and tracking. Although only the KI 525A Pictorial Navigation Indicator (PNI) and the KA 51B Slaving Control & Compensator Unit appear in the aircraft panel, other remote components  of the KCS 55A system include the KMT 112 Magnetic Slaving Transmitter, the KG 102A Directional Gyro for stabilization of the system and optionally the KA 52 or KA 57 Autopilot Adapters making the KCS 55A a complete slaved compass system. Installation parts and manuals of the above components are sold separately. For further information on these components please refer to their individual product presentations. For additional information on  KCS 55A and technical specifications please consult the Product Description section.

The HONEYWELL BENDIX KING® components of KCS 55A Compass System can be furnished in NEW condition or as USED in Serviceable or Overhauled conditions indicated respectively by the letters "SV" and "OH" in the product reference numbers (SKU and  accompanied by the relevant certification (e.g. yellow tag, 8130-3 form). They are also offered as exchanges / trade-ins  for returned customer owned units indicated by the letter "EX" in the SKU. In the case of an exchange/trade-in option of a customer unit, the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders when our co-operating supplier verifies that the unit is in a reasonable, repairable condition. It is recommended that this option is selected by our customers mainly for upgrades and only in cases when their units are functioning properly at the time removal from the aircraft. In cases when customer units are found by our supplier to be non-repairable, the core deposit shall not be refunded and shipping charges shall apply if customers wish the return of these units to them. 

WULTRAD INC. is a manufacturer of non-certified flight and engine instruments under FALCON GAUGE brand for experimental and homebuilt aircraft. Although their products are Non-TSO, they are made to TSO or MIL specifications for quality.

FALCON GAUGE Non Certified Airspeed Indicators have been one of the most chosen flight instruments by fixed wing airplanes, helicopters and ultralights. The great advantages of these gauges are excellent slow speed characteristics, very progressive increments, a variety of ranges, light weight, short length, and affordable price. FALCON GAUGE Airspeed Indicators ranging up to 80 MPH, 100 MPH, 120 MPH and 150 MPH make for excellent MPH increments for helicopters and ultralight aircraft. All FALCON GAUGE Airspeed Indicators are housed in an aluminum case and consist of all metal parts. They come in 2-1/4" and 3-1/8" sizes. Available ranges: MPH, Knots, KPH; single range or dual range readings. Optional: Custom color range markings can be special ordered. For additional information please refer to the supplied documentation or contact us.

The Ameri-king AK-920F is a FAA TSOd approved GPS/Avionics fan, compact sized, delivers up to 26.6 CFM cubic feet per minute of forced air cooling to a variety of avionics equipment. It features ball bearing for highest reliability and long lasting. The AK-950F fan may be behind or beneath aircraft instrument panel or avionics equipment rack or cabin pressure bulkhead.

Product Features:

Power reverse polarity protection

Compact size

Choice of 1, 2, 3, or 5 hose outputs

Universal mounting

Hoses-Connector kit and hardware (included)

4-year extended warranty

Power: 14 or 28 VDC

AIRPATH certtified (FAA TSO) Magnetic Compasses are used in almost all production aircraft. They are offered in in different panel mount and pedestral models,  lighted or non lighted versions, black & white markings, black finish, and capabilities for operations in South or North Hemisphere. 

AIRPATH C2300 panel mount magnetic compasses fit in a 2.25 in. hole and need 3 in. of clearance from behind the panel. Offered Models(*): C2300, C2300-SF, C2300-L4, C2300-L4-SF.Compass fluid is included inside the units and come with the mounting screws and nuts required for their installation. A compass deviation card and card holder can be ordered separately. 

AIRPATH C2400 series pedestral magnetic compasses have been specifically designed for installation either for streamline-type bracket housing or a pedestal-type housing. Wire lead length, voltage, and lighting color are specified under each respective part number. Each model is provided with mounting hardware, deviation card, deviation card window and either an attached cardholder, deviation plate, or standard unattached cardholder depending on the application. All compasses in the C-2400 series meet FAA TSO-C7c requirements and are offered in different versions for operations in South or North Hemisphere. They fit in a 2.25 hole. Lighting: Red 12 VDC. Meet FAA TSO-C7c requirements.

(*) Letter “L” after the dash in the part number indicates a lighted version. Letters “SF” indicate South Hemisphere.

JPI FS-450 Fuel Scan is a top choice low price unit for fuel management of an aircraft, offeredin different versions with single transducer available for gravity, pressure and ROTAX engines or with a Flow Scan 201 or 231 transducer and harness for pressurized carb engines.

HONEYWELL BENDIX KING® KI-229 Radio Magnetic Indicator (RMI) provides bearing information to either ADF or VOR stations by means of two pointers each of which is read against compass card.

The KI-229 RMI combines three data points on one indicator. The current aircraft heading from an HSI is shown on the card. The magnetic headings to VOR and NDB stations are shown by the twin needles. By combining all this information visually, less interpretation is required thus enhancing overall situational awareness, something especially helpful when the workload is high.

The KI-229 requires inputs from ADF, HSI and NAV receivers.

Product Features:

14/28 volt lighting

Compatible with Nav Receivers such as KN-53, KNR-615, KNR-630/631/632/633, KNR-634, KNR-665, and KNR-665A

Compatible with Nav systems including RNAV such as KNS-80 and KNS-81

Compatible with ADF receivers such as KR-87 and KDF-806

Compatible with Compass systems such as KCS-305 and KCS-55/55A

Requires input ARINC Compass System

TSO'd

Product Specifications:

TSO Compliance: Env. Cat. RTCA DO-160A A1C1/A/SKP/XXXXXXA/B/AAA

Weight: 2.8 lbs. (1.3 kg)

Temperature: -20 to +55°C

Altitude: 35,000 feet

TSO (Compass): TSO C6c

TSO (ADF): TSO C41c Class A

TSO (VOR): TSO C40a

Heading Input: Operates from any slaved magnetic compass with ARINC X,Y,Z outputs

VOR Video Input: 0.5VRMS 0 deg. phase composite 30Hz variable AM and 30Hz reference FM on a 9960Hz carrier (0.7VRMS maximum)

The R.A. MILLER (RAMI) TSO'd AV-74 (.425 Stud Length) & the AV-74-1 (.800 Stud Length) are broadband blade type antennas for transponders or DME applications. The antenna housing is constructed of an acrylonitrile-styrene-acrylic (ASA) shell. The white color allows maximum performance without losses due to color pigments or unseen dirt. The antennas are supplied with cellular neoprene mounting pad and hardware. Designed to operate at speeds up to 350 mph and altitudes up to 50,000 ft. They have a drag force of 0.09 lbs @ 250 mph. These antennas are direct replacements for the CI-105 antennas.

Product Specifications:

Application: Transponder/DME

Frequency: 960 - 1220 MHz

Impedance: 50 Ohms Nominal

VSWR: 1.5:1 Maximum

Polarization: Vertical

Pattern: Omni-Directional

Connector: "BNC" Female

Max Height: 3.4"

RF Power Capacity: 2.5 kW Peak

FAA TSO: C66c, C74c

These UMA new manufacture NON TSO'd electric ammeters offer accuracy, rugged construction, and contemporary styling. They are available in different  measurement ranges with a 270° sweep and are suitable for installation in 2-1/4" panel hole diameters. Made in U. S. A. and furnished with shunt.

YAESU rechargable batteries are intended for use with YAESU handheld transceivers.

Automatic portable radio beacons (ELT(AP) АРМ-406П (ARM-406P), АРМ-406П1 (ARM-406P1) and АРМ-406АС1 (ARM-406AC1) are safety devices designed to transmit via satellite to the stations COSPAS-SARSAT distress radio signals with aircraft coordinates received from the onboard computer system.Such information facilitie identification of the aircraft and guidance of S&R facilities to the accident site. Located in the aircraft cabin these devices offer the possibility of quick use in an emergency.

The automatic portable radio beacon АРМ-406П1 (APM-406P1) includes:

- monoblock P, consisting of a double protective casing with shock absorbers installed in it, an overload sensor (DP) and an AC1A monoblock;

- remote control PDU-406 (ПДУ-406) installed in the cockpit;

- external antenna ANT-406VA (АНТ-406ВА), mounted on the aircraft body.

The АС1А monoblock is  a portable radio beacon, including a PM-AC1A (ПМ-АС1А) transmitting module, an АРМ-043-01 autonomous power supply unit and an ANT-APM-01 (АНТ-АРМ-01) antenna. The emergency mode of operation of the AC1A monoblock can be switched on both from the remote control and from the DP, as well as manually when removing it from the protective casing when leaving the emergency aircraft.

Autonomous power supply (APS) units are also offered for use with the radio beacons. АРМ-043 (CDKT.436140.590) 14.4V are intended for use for beacons manufactured before 2013 while АРМ-043-01 (CDKT.436140.590-01) 10.8V for beacons manufactured after 2013. Unless otherwise specified their replacement frequency is once every 3 years with a 3-year self life.

For additional information please refer to the supplied documentation or contact us.

EASA Certified VHF transceiver in 160mm format with 6W output power. Automatic selection of 8.33kHz/25kHz spacing and OLED display.