JPI FS-450 Fuel Scan is a top choice low price unit for fuel management of an aircraft, offeredin different versions with single transducer available for gravity, pressure and ROTAX engines or with a Flow Scan 201 or 231 transducer and harness for pressurized carb engines.

The SIRS "Navigator" magnetic compass delivers extremely accurate readings due to its fully integrated, 4 magnet correction facility.  It has the same features as the "Pegasus", but is mounted with a fully adjustable bracket that allows attachment to a variety of positions including the glare-shield or the windshield. This allows the compass to be located away from magnetic influences. Available in different versions for Northern or Southern hemisphere, unlighted  or lighted 12/28V and has a 3-year warranty. Size: 203/8" H x 2-1/4" W. Product accessories such as installation kit, GS1 glareshield mount, SIRS MF1 short foot bracket and SIRS compass correction key are also available and sold separately.

The RCA 56 Series of electric turn and bank indicators by KELLY MFG (RC ALLEN) are an all volt instrument, with a power warning flag, a black or white ball inclinometer and either lighted or non-lighted. These rate-of-turn pointer controlled instruments are powered by an electrically driven DC precision gyro with an inclinometer providing the pilot with turn and bank information.  They meet or exceed requirements of FAA TSO C3b. Made in the USA. Weight: 1.9 lbs.

Dimensions: Length: 6 1/4 in. Max, Width: 3 3/8 in. Max, Height: 3 3/8 in. Max

Mating Connector: MS3106A10SL-3S.

Connector Pin Out: A: +11-30 VDC, B: Ground, C: Spare

FLYBOX® EFC-P Electronic Flap Controller by MICROEL SRL allows selection of the desired position of the flaps of an aircraft. EFC-P Controllers are offered in Rectangular (P/N: EFC-P-102010) or Round (P/N: EFC57-P-103010) versions. They are intended for use in ultralight and experimental aircraft. The working mode consist in selecting one of the four positions previously stored by the user, then the EFC-P will automatically moves the flaps in the exact position. The LEDs show the current position of the flaps or, when in movement, the position that they are reaching. For further information please refer to the attached documentation.

UMA Electronic Hydraulic Pressure Gauges are offered in TSO'd and Non TSO'd models and 1-1/4"  or 2-1/4" diameters to fit respective aircraft panel openings. They are housed in aluminium or Valox 420 plastic cases (depending on the model) and connect to  precision, high pressure transducers which mount directly to the aircraft's hydraulic system. Standard markings are black and white. Recommended for new design projects and applications. 

Note: Pressure Transducers (Senders) ARE NOT INCLUDED in the prices of the pressure gauges. They are sold separately and are not TSO'd.

FALCON GAUGE Magnetic Compasses are non certified  2" compasses available in liquid (MCDN) and non-liquid (dry) types (MCVC). The Liquid Type compasses provide an accurate reading at a low cost. They are fluid damped and incorporate a thermal expansion chamber and compensating magnet. Available in Panel or Pedestal Mount versions with or without lighting. Different models available: MCDN-2, MCDS-2, MCDN-2L, MCDS-2L. They can be ordered for Northern or Southern Hemisphere.

These compasses are very similar to the Airpath C2300 & C2400 style compasses, but are priced more economically.

The FALCON GAUGE Vertical Card Compasses are of a non-liquid type.  They are designed with a different concept which eliminates the disadvantages experienced with a liquid compass, namely leaking and back and forth motion of the compass card.  These compasses look like directional gyros and offer superior visibility.  A second vertical rotating dial, which is compared with a fixed miniature airplane (lubber line), presents the magnetic heading of the aircraft at all times making heading information more natural.  The easy to read presentation allows the pilot to see the complete 360 degree dial.  They also feature an internal LED light and a universal mounting bracket.

DAVTRON Μ475 Series 2-Function voltmeter/ammeter digital indicators are FAA-PMA approved and come in 475VA/475VAA models and versions, both with lighting capability. Model M485VA ls made primarily for remote shunts. They are both designed for low current drain ( .001 Amp) and are also used in standby and emergency battery packs. Other features include: 

Plus Or Minus Amp Range: 150.0 

Plus Volt D.C. Range: 100.0 

Sunlight Readable Display

One Tenth Amp Resolution

One Tenth Volt Resolution

1.3" case depth

2-1/4" Standard mount

The MID CONTINENT® INSTRUMENT (MCI) 3" TSO'd Turn Coordinators are value priced  and engineered for reliability and a long service life. Depending on the model, they can be a direct replacements for most coordinators with 3-pin or 5-pin connectors. 

These instruments show  a standard 2 minute turn when balance ball reaches either side of display. MCI turn coordinators feature a HEA non-glare glass screen for easy readings, an operating range of temperatures from -30 to +50 deg. C and altitude-1000 to 35000 ft and they can operate on a voltage range from 10-32 VDC for convenience. Power consumption is 0.28 A. They can be front or rear panel mounted in a 3 1/8" hole. Dimensions: 3 1/4"X3 1/4"X5". Max Weight: 1.4 lbs. Available in lighted and unlighted versions. FAA TSO certified to C3b.

The “B” models are equipped with a proven AC rotor powered by a solid-state inverter, creating less heat behind the panel. Utilizing a brushless rotor design, these models exhibit top industry ratings of 4,800 hours MTBF. They are ideal for use in high performance aircraft and cold-climate applications.

These UMA new manufacture NON TSO'd electric ammeters offer accuracy, rugged construction, and contemporary styling. They are available in different  measurement ranges with a 270° sweep and are suitable for installation in 2-1/4" panel hole diameters. Made in U. S. A. and furnished with shunt.

FALCON GAUGE  Electrical Turn Coordinator is used for displaying the angular rate and sideslip of turning in horizontal flying and turning. The inclinometer indicates the slip angle of the aircraft while in a turn. A power failure flag drops into view whenever the voltage drops below a level for proper operation. The Turn Coordinator incorporates a built-in voltage regulator so it can be used with either 14VDC or 28VDC power system. It is compact in size and light weight eliminating radio interference.

This small, lightweight unlighted turn coordinator is excellent for homebuilt aircraft. Works for 14 Volt or 28 Volt systems. Features, power out warning flag with a 0° Panel. Fits Standard 3-1/8" Cut Out, 3-3/4" long.

KANARDIA AETOS Basic EFIS Kit is a Non Certified complete navigation, flight and engine system for the ultralight airplanes, autogyros and helicopters. This self-contained state-of-the-art EFIS instrument is optimized for ultralight aircraft.

The AETOS Basic EFIS Kit comes with a large 7" sunlight-readable display with high contrast and integrated AHRS and GPS unit (AIRU), engine monitoring unit (DAQU), OAT probe, GPS antenna, cables & accessories. Engine sensors are not included in this kit. In contrast to NESIS EFIS, AETOS EFIS does not support flight maps. Options are available at additional cost to increase the functionality of this device.

4-Pin connector by AMPHENOL for use in all electrical gyros (DG or Horizon) including Falcon models.

The RAY ALLEN (RAC) RP4 LED position indicator is designed to be installed in the cockpit providing an indication of the servo output shaft position. This indicator supercedes and it is a direct replacement for previous RAC RP3. The RP4 indicator uses ten LED lights to show the position of a actuator output shaft (or position sensor arm). There are also two amber colored LED's, one on each end of the indicator scale, to act as a reference for the green indicator light, especially in dark conditions. The 10 LEDs are the brightest available for superior visibility in sunlight, but can be dimmed for night flight. It can be installed horizontally or vertically. 

The RAC RP4 position indicator is panel mounted using a faceplate and two countersunk, 2-56 x 7/16" screws (two spare finishing screws are included). The distance between the screw holes is identical to the older Ray Allen RP3 LED indicator. Although the faceplate dimensions are identical between the RP3 and RP4 indicators, the panel cutout size is slightly different between the RP3 and RP4. If you are replacing and older unit with a new RP4, you will only need to increase the size of your panel hole. The RP4 faceplate will cover the older RP3 panel hole.The RP4 faceplate measures 1.75"(45 mm) X .75"(19 mm) and it is 1.6"(41 mm) in depth. It is now the standard position indicator included in Ray Allen trim systems, or can be purchased separately for special applications such as a cowl or wing flap indicator.

The RP4 includes a RP4-L1 label (featuring Elev1, Elev2, Ail, Rudder, Flaps). A RP4-L2 label (featuring Cowl Flaps, < >, on/off) is also available and is sold separately. 

NOTE: Labels can only be ordered together with . In ordering these high quality labels please be advised that rocker switches and needle indicators require a large label, LED indicators use a small label. Can be only included in orders of respective RP4 position indicator(s) (not separately).

G-Meters (Accelerometers) by FALCON GAUGES measure G forces acting on the airframe during turbulent or aerobatic maneuvers. One pointer providess a continuous reading, the other two indicate maximum positive and negative loads. FALCON G-Meter models are mechanical and offer precision, accuracy, and durability. They are also easy to operate. No wiring necessary. The units come with the locking knob set to the locked position.  Do not press the reset button until after moving the locking knob to the unlocked position.

FALCON GM510-2 G-Meter is a standalone 57 mm (2 1/4") unit which fits a standard 2 1/4" instrument cutout.

Product Features and Specifications:

Product Features:

• G-Meter, -5 to +10 g

• Operation Temperature: -55º to +60°C

• Dimensions: 61 mm (2 1/4") x 61 mm x 108 mm (3.5")

• Complies with Standard : MIL-A-5885C

Note: FALCON GM510-2 G-Meter is currently not available. Availability in NEW condition depends on existing stocks and is limited.

TSO'd Electronic Fuel Quantity gauges from UMA INSTRUMENTS (indicated by the letter "T" in the PN) are offered in 1-1/4 in. and 2-1/4 in. sizes for installation in respective panel hole diameters and mounted with (4) 6-32 screws. Smaller 1-1/4 in. instruments can be cluster mounted as close as 11/2” centers utilizing panel space without compromising readability. They can be powered from 14 or 28 volts. Signals are acquired from remote mounted sensors, processed and displayed on black analog dials with white easy to read markings indicating empty to full fuel level. Each gauge uses rugged aircore meter movement for vibration resistance and repeatability. Available in different versions based on their sender type and range. UMA sensors are sold separately.

TSO'd Electronic Fuel Quantity gauges from UMA INSTRUMENTS (indicated by the letter "T" in the PN) are offered in 1-1/4 in. and 2-1/4 in. sizes for installation in respective panel hole diameters and mounted with (4) 6-32 screws. Smaller 1-1/4 in. instruments can be cluster mounted as close as 11/2” centers utilizing panel space without compromising readability. They can be powered from 14 or 28 volts. Signals are acquired from remote mounted sensors, processed and displayed on black analog dials with white easy to read markings indicating empty to full fuel level. Each gauge uses rugged aircore meter movement for vibration resistance and repeatability. Available in different versions based on their sender type and range. UMA sensors are sold separately.

DAVTRON M301 Series Outside Air Temperature (OAT) digital indicators are FAA-PMA approved and come complete with digital probe, in Fahrenheit or Celsius models and different versions. They require minimum panel space. Other features include: light weight, automatic dimming, miniature remote probe, sunlight readable display and a laser engraved faceplate. A 3-pin connector is installed on probe as an option for an additional charge.

This line of FAA PMA'd  miniature engine gauges from Mitchell is ideal for a wide variety of general aviation applications. They measure nearly 1-1/2 inches square and are stackable. The modular design allows them to be plugged from the front of the panel. The units are internally lighted. Complete standard panels are also available.

FAA Approved. If individual gauges are ordered, appropriate backplate with pigtail must be ordered to mount and connect the gauge. If more than one gauge ordered to be mounted together, a special order cluster that requires custom backplates.

KANARDIA INDU Series round Airspeed Indicators are part of INDU diverse family of non-certified gauges for use in ultralight aeroplanes, autogyros and helicopters. They feature an LCD display with possibility to personalise the displays and scales. They are offered as standalone (master) IAS units with internal pressure sensors or as slave instruments. The slave version requires a master altimeter or some PFD like KANARDIA NESIS, EMSIS, AETOS or HORIS to be present on the CAN bus. 

KANARDIA INDU Series round altimeters are available for two standard panel hole diameters of 57 mm (2.25") and 80 mm (3.15"). As an option they can be ordered with an Outside Air Temperature (OAT) digital sensor at additional cost. When static pressure (altitude) is present on the CAN bus, OAT sensor enables also the TAS  as well.

Scale Ranges:

-KMH Scale in kilometers per hour (0-280)

-KTS Scale in knots (0-140)

-MPH Scale in miles per hour (0-150)

NOTES:

A high speed sensor option is also available at additional cost (up to 460 km/h, 250 kts, 285 mph)

Arc colors need to be specified  at the time of order.