SKY-TEC, a HARTZELL ENGINE TECHNOLOGIES brand, includes starters and support for Prestolite, Electrosystems, Lamar and Kelly designs. SKY-TEC OEM contactors are today installed in many general aviation aircraft while SKY-TEC FAA-PMA contractors can be used for starter, battery master/auxiliary or auxiliary power applications in replacement of OEM parts.

SKY-TEC STS-S Series FAA-PMA certified aircraft starter solenoids (aka relays) are intermittent duty suitable for starter applications. They are available in 12V (STS-S12) or 24V (STS-S24) versions. Activation: +V to S-Terminal (Frame is grounded by mounting).

SKY-TEC STS-M Series FAA-PMA approved Battery/Master solenoids are continuous duty solenoids intended for use in battery master/auxiliary applications in certified aircraft. They are available in 12V (STS-M12) or 24V (STS-M24) versions. Activation: -(Ground) to S-Terminal. (Floating ground frame).

SKY-TEC STS-A Series FAA-PMA approved solenoids are continuous duty and typically used for connecting auxiliary (ground) power. They are available in 12V (STS-A12) or 24V (STS-A24) versions. Activation: varies.

Product Features:

FAA-PMA Certified

All-metal case construction

Silver contacts (vs. copper) for high-current capability and long-life. They provide 300A in-rush capability. Much higher than the original units.

Strong spring and high-current coil for quick contact opening - minimizing arcing

Single coil terminal (other end connected to case)

High quality manufacturing 

Upgraded to perform best with today's lightweight, high torque starters

Same OE terminal layout simple to install

For additional information on different SKY-TEC series of slenoids and their applications in different aircraft please refer to the respective product presentations.

Pitot tubes scan the static and dynamic pressure, and they are used on aircraft to determine the aircraft airspeed. 

WULTRAD INC. is a manufacturer of non-certified flight and engine instruments under FALCON GAUGE brand for experimental and homebuilt aircraft. Although their products are Non-TSO, they are made to TSO or MIL specifications for quality. 

FALCON GAUGE Non TSO'd (non-certified) pitot tubes have been used for many years on different types of experimental or other aircraft where no certification is required. Available in different heated and unheated versions for 12 or 24 V electrical supplies, for vertical or flat installations. Standard (3/4") and long (4") mounting brackets are offered. Heated Material: Stainless Steel. Please consult the supplied documentation or contact us for further information.

Bi-metallic push to reset only thermal circuit breakers suitable for homebuilt aircraft. Used as original equipment in Beech, Cessna and Piper aircraft. 0.5 amp to 30 amp ratings. Maximum operating voltages: 32 VDC and 250 VAC (to 400 Hz).

Product Features:

Push To Reset Only

0.5 amp to 30 amp ratings.

Cannot be manually tripped.

Button extends for visual trip indication.

Push button to reset breaker.

90 Degree Screw-On Terminals

Switches for different functions, inteneded for use in Piper aircraft. Information on their applicability to different Piper aircraft models and serial numbers is included. For additional information and/or non listed switches please contact us.

Master Relay (Battery Solenoid) for all homebuilts (not suitable for certified aircraft). Continuous duty. Offered for 12V and 24V systems.

RED BOX® AVIATION, part of the LPA Group, offers a comprehensive range of aircraft ground power equipment including ground power units, aircraft start power units, aircraft connectors and more.Their ground power range or aircraft GPU, are designed for the civilian and military markets, while the majority of their products are also NATO codified. 

RED BOX® AVIATION aircraft hand portable start power units (packs) are included among the most powerful hand portable packs worldwide. they are based on military aerospace technology to achieve a very high power to weight ratio. These power packs are designed for starting of piston, turboprop or turbine aircraft and helicopters in the field or in remote locations while RED BOX® units may also be carried safely on board all aircraft. The power packs are “all weather” units and being modular, can be used in single or dual format. They can be used or stored in any orientation, even inverted. Cells used are cleared as non-hazardous cargo for carriage in the aircraft. They are able to operate in extremes of temperature and have excellent standby characteristics. They are maintenance free and do not require cycling. They can be re-celled “on condition” at any RED BOX® service center and are designed to offer years of repeated service. In addition to aviation, these highly portable units can be used with Armored Fighting vehicles and Military equipment. They can be recharged from the automatic charging system, which is supplied in the package, or from any vehicle using a suitable interface.

Product Features:

Offered models in different voltages and amperages

Totally weather protected

Air transportable

Non-hazardous

Maintenance Free

Tough and compact

No memory effect

Works in any orientation

High charge retention

Long shelf life

Fast recharge

No cycling

Leak proof

Electrodelta (Hartzell Engine Technologies) is the world market leader in top quality voltage regulators for general aviation aircraft, and continues to revolutionize the industry with proven technologies and improvements. The units are assembled from the highest quality electronic components available and are meticulously tested and calibrated to ensure maximum performance.The Electrodelta product line was acquired by by Lamar Technologies LLC in order to add new and alternative  parts to the company's product lines.

The RBC® BEARINGS offers a full line of airframe control ball bearings to the aerospace industry  in both “Standard” and “Precision” series. The prefix “M” in a bearing number indicates that it is of a precision series. Although designed and manufactured under demanding quality control requirements for airborne systems, these bearings have been successfully used in many industrial applications, where oscillatory movement, high loads, or corrosive environments are prevalent.

RBC® BEARINGS airframe control ball bearings conform to SAE-AS7949 (formerly MIL-B-7949) and many major OEM specifications. These bearings are of lightweight design, corrosion-resistant, grease-lubricated, and typically sealed. Airframe control bearing rings and balls are made of hardened bearing alloy, AISI 52100, with all exposed surfaces, except bearing bore, caps and seals, plated for corrosion protection. For improved corrosion protection, RBC® BEARINGS  supplies bearings made of hardened stainless steel alloy, AISI 440C. This alloy may be passivated or plated with cadmium or zinc nickel for enhanced corrosion protection.

The RBC® BEARINGS MKP/MKP-A SAE-AS7949 Precision Series airframe control bearings are single row, heavy duty (MKP) or medium duty (MKP-A) radial ball bearings with PTFE seals and CRES sealcaps. MKP Series bearings conform with MS27640-R specifications while those of MKP-A Series with MS27641-R. External surfaces (except bore, caps, and seals) are cadmium plated. They come prelubricated for life and are also offered with CRES 440C material and/or zinc nickel plating per OEM specifications. For additional information please refer to the supplied documentation.

YAESU rechargable batteries are intended for use with YAESU handheld transceivers.

DYNON AVIONICS AOA/Pitot probes perform two functions: airspeed and angle of attack sensing. These functions require having two pressure ports on the tip of the probe. The normal pitot pressure port is on the front face of the probe and is designed to be insensitive to angle of attack. The second pressure port is located on an angled surface just under the pitot port and is designed to be very sensitive to AOA. They are under-wing mount, L-shaped  probes which can be installed  easily with simple plug-n-play integration with Dynon and Advanced Products.Their installation requires a mounting bracket sold separately. The pressure from each port is delivered via separate air lines to the instrument where they are compared to previously calibrated scenarios specific to the aircraft. Competitively priced, they are offered in Non-Heated and Heated versions. The Heated AOA Pitot includes a nichrome heating element that is regulated by a separate pitot heater controller unit supplied with the pitot. The controller actively monitors a temperature sensor embedded within the pitot head and regulates the power to maintain a constant temperature. This not only conserves energy but additionally prolongs the life of the heater. The controller also outputs a signal that can be wired to a warning light in the cockpit to warn the pilot anytime there is a malfunction or that the pitot is turned off.

The HEIM® BEARINGS company has been acquired by RBC® BEARINGS, a leader in the world of highly engineered bearing products. 

HEIM® BEARINGS produces the industry's widest range of rod end bearing sizes (aka rod ends) in  the following four grades (types): precision, aircraft, military and commercial with each grade including different series suitable for respective application requirements. HEIM® BEARINGS are made from different materials featuring among others high strength two piece designs, high capacity designs, self-lubricating options and thermoplastic races or Teflon® liners. Please consult the supplied table on different grades and series offered.

- Precision rod ends are manufactured to tight tolerances for applications requiring improved linkage accuracy and reduced looseness. 

- Aircraft rod ends use premium materials, and have magnafluxed rod end bodies. Originally intended for aircraft applications, aircraft rod ends are used in many industrial applications where a high degree of reliability is required

- Military rod ends are produced in strict accordance with all applicable military specifications and are typically used in military and commercial aviation applications, or when Mil-Spec approval is required

- Commercial rod ends are produced using standard materials and manufacturing methods, and consist an economical choice for industrial applications

The HEIM® BEARINGS ME/AS81935/1 and FE/AS81935/2 series are military standard, high capacity self lubricating rod ends, male and female threaded respecively, using HEIM® UNIFLON® liner approved to SAE-AS81820 (formerly MIL-B-81820). Their rod end bodies are made from 4340 alloy steel, heat treated, magnetic particle inspected, cadmium plated and chromate treated. Balls  are made from 440C on 17-4PH race inserts and heat treated.

Letters “L” and “K” to prefix indicate Left Hand thread and Keyway respectively.

Please refer to the supplied chart for technical specifications and the RBC® HEIM® Bearings Catalog for additional information.

The ACS unvented flush fuel cap operates with a lift and turn lever. This cap has a 3" opening for easy refueling. Cap & adapter ring are anodized "clear" for corrosion resistance. Cap is fastened to adapter ring with safety chain.

Clip-Locking Turnbuckles utilize 2 locking clips instead of lock-wire for safety. The turnbuckle barrel and terminals are slotted lengthwise to accommodate the locking clips. After the proper cable tension is reached the barrel slots are aligned with the terminal slots and the clips are inserted. The curved ends of the locking clips expand and latch in the vertical slot in the center of the barrel. They are available for different cable diameters and thread sizes in inches covering desired minimum breaking strength requirements.Different turnbuckle components are used in turnbuckle assemblies. They are sold separately to meet application requirements. Please refer to the attached documentation.

RBC Aerospace Bearings offers a full line of Mil Spec standard lined journal bearings, unlined bushings, and many specialty and custom designed products to support the aerospace industry.   Journals are designed in a straight (plain) configuration with a flange to accommodate a combination of radial and axial loads with corrosion resistant materials and coatings. Journals are also offered in high temperature and water resistant series. Typical journal materials are CRES 17-4PH and aluminum.  Bearings may also be cadmium or zinc nickel plated as required while CRES 440C and Inconel® 718 are available upon request. Journal bore and flanged journal face surfaces may also be provided with various liner systems to satisfy specific application requirements. Machinable liners  are qualified to AS81934 (formerly MIL-B-81934). For additional information please refer to the attached documentation.

FLYBOX® brand  by MICROEL SRL relates to a wide range of avionics and flight instruments specialy designed and developed for ultralight and experimental aircraft. FLYBOX® product portfolio includes 

My-EMS & Vigilus Engine Monitoring Systems

Engimaster EMS Engine Monitoring Systems

Oblò,  Oblò 2 and Eclipse NG Electronic Flight Instrument Systems (EFIS)

Omnia 57 and 80 Series of Legacy Instruments/Indicators

FLYBOX® Autopilot Systems

Flap & Propeller Controllers

For further information please refer to the Product Description section & the supplied documentation.

Wire/cable dash controls are locking units securing wires/cables from turning loose from vibrations. These controls can be mounted from front or rear of instrument panel.

T-handle dash controls are offered as part of our own branded (AVIATIONEU NEW ERA) product lines. They are sourced from quality manufacturers and made from duralumin and brass. One-fourth turn locks them in any position. T-handle dash controls have a width of 1-3/4" and a standard 2-1/2" travel. They can hold up to 100 lbs. These controls are offered in single or two wire versions and come complete with wire(s) and casing which may be shortened.

In the two-wire T-handle dash controls, two cables come out of the T-handle. The inside wire is .073" and the outer housing is 2" OD. Single wire T-Handle dash controls are available in three models with 5, 8 or 12 feet cables with the following specifications:

Model No.:36338100

Cable Length: 5 ft

Mounting Thread: 7/16-20

Wire/Cable Diameter: 0.054 in.

Cable Housing Diameter: 0.190  in.

Model No.: 36200046

Cable Length: 8 ft

Mounting Thread: 7/16-20

Wire/Cable Diameter: 0.072  in.

Cable Housing Diameter: 0.215  in.

Model No.: 36200047

Cable Length: 12 ft

Mounting Thread: 7/16-20

Wire/Cable Diameter: 0.072  in.

Cable Housing Diameter: 0.215  in.

The RBC® BEARINGS offers a full line of airframe control ball bearings to the aerospace industry  in both “Standard” and “Precision” series. The prefix “M” in a bearing number indicates that it is of a precision series. Although designed and manufactured under demanding quality control requirements for airborne systems, these bearings have been successfully used in many industrial applications, where oscillatory movement, high loads, or corrosive environments are prevalent.

RBC® BEARINGS airframe control ball bearings conform to SAE-AS7949 (formerly MIL-B-7949) and many major OEM specifications. These bearings are of lightweight design, corrosion-resistant, grease-lubricated, and typically sealed. Airframe control bearing rings and balls are made of hardened bearing alloy, AISI 52100, with all exposed surfaces, except bearing bore, caps and seals, plated for corrosion protection. For improved corrosion protection, RBC® BEARINGS  supplies bearings made of hardened stainless steel alloy, AISI 440C. This alloy may be passivated or plated with cadmium or zinc nickel for enhanced corrosion protection.

The RBC® BEARINGS Airframe Control Ball Bearings are offered in different series. The KP/KP-A and KSP/KSP-A series, presented separately, are briefly discussed below.

KP (Heavy Duty) and KP-A (Medium Duty) SAE-AS7949 Series radial ball bearings  manufactured with Plyoseals. KP heavy duty single row sealed bearings comply with MS27640 specifications while KP-A medium duty single row ball deep groove sealed bearings with MS27641 specifications. Both KP and KP-A radial ball bearings are prelubricated for life and feature PTFE seals and CRES sealcaps, cadmium plated exposed surfaces except bore, caps, and seals. Both are also offered with CRES 440C material and/or zinc nickel plating per OEM specifications. Load limit ratings: Radial 1230-lbs, thrust 300-lbs.

KSP/KSP-A Series SAE-AS7949 Series single/double row, self-aligning, light and heavy duty ball bearings with bonded PTFE seals and cadmium plated exposed surfaces except bore, caps, and seals. Like those of KP/KP-A Series, both KSP and KSP-A bearings are prelubricated for life and are also offered with CRES 440C material and/or zinc nickel plating per OEM specifications.

For additional information please refer to the supplied documentation in the respective product presentations.

The company SPECIALITY TIRES OF AMERICA (formerly McCREARY TIRE & RUBBER providing automotive tires) manufactures a wide range of aircraft tires under different brands including SUPER HAWK®, AIR HAWK®, AIR TRAC®, AERO CLASSIC® & AERO TRAINER® as well as matching tire tubes. Different brands (series) briefly presented below are separately listed. For more information please refer to the supplied documentation.

SUPER HAWK® tires are the best choice when  the highest levels of performance and extra-long tread life are required. Designed to handle higher landing speeds and heavier loads, these tires combine advanced design & over 90 years of precision tire craftsmanship resulting in premium belted aircraft tires that surpasse FAA specifications and match the performance of more expensive brands.

AIR HAWK® tires are premium grade & priced tires, but provide longer service life. Excellent choice for a wide range of applications. Improved tread compounds and high-strength casings offer added wear resistance and an extra measure of security. AIR HAWK® tires are FAA approved and tested by thousands of pilots, delivering a reliable, cost-effective performance under a wide variety of takeoff and landing conditions. 

AIR TRAC® fine nylon cord narrow-ribbed, oval shaped tires are designed for soft field applications and rigidly tested to meet FAA Standard TSO-C62. The  AIR TRAC  tires consist an excellent choice for single engine, piston aircraft. Thesy are ideal for aircraft operated on grass strips while being perfectly usable on hard surfaces. These tires are are original equipment on many of today’s aircraft and offer a great performance in an economical tire. AIR TRAC® tubes are the perfect match to the AIR TRAC®  tires. 

AERO CLASSIC® tires are designed specially for classic planes including warbirds, DC-3's, and Beech 18's, often the only manufacturer producing tires for these aircraft. The product line includes over 50 tires and tubes, from 8" diameter for tailwheels, up to 56" diameter C-130 inner tubes. AERO CLASSIC® tubes are tested to MIL-I-5014F standard. 

AERO TRAINER® tires are designed for flight schools with single engine trainers. They combine the high quality and durability with a competitive price.

SPECIALITY TIRES products are supplied with a standard Certificate of Conformance. If an FAA/EASA Form is needed (depending on the ordered item) please mention this during the order placement. In this case, additional cost may apply.

CURTIS PLT-275AV Flush Valves 6 Holes' Adapter Plates Assembly.

Product Specifications:

Diameter: 2.75 in.

Depth: 640,000-650,000

From Mounting Surface to Bottom Hole Diameter: 1-1/2 in.

Not Certified

MAGNUM aircraft rescue ballistic parachute systems (also known as  Vertical Launch Systems, VLS) are manufactured by STRATOS 07 S.R.O with knowledge and long experience in the construction of system components including rocket motors. They include different series produced for many years (like 450, 450 Speed, 501, 601) & newer certificated rescue systems like Magnum 1201 & 1401 for heavier aircraft and higher deployment speeds. They are intended for use in hang-gliding, paragliding, powered hang-gliding, powered paragliding,  unpowered and powered gliders,  gyroplanes as well as a wide range of two- and multi-seat airplanes and helicopters, including Light Sport, Experimental and Ultralights with a maximum 3,960 pounds gross weight, and deployment speeds of up to 199 MPH. Magnum Ballistic Parachutes come in sofpacks or canisters. Rescue systems packed in the softpack are usually installed inside of the aircraft. Rescue systems packed in a duralminium container are installed mostly outside of the aircraft.

Please refer to tables of specifications and notes below for the selection of a right rescue system.

Notes:

The max take-off weight of the aircraft MUST NOT EXCEED the max allowable load of the rescue system.

If the aircraft Vne exceeds the max limiting speed for the rescue system deployment, mounting of the system should be done so that the pilot is informed of this speed.

MAGNUM ballistic parachute systems  are packaged in two parcels (one containing the parachute and the second containing the rocket). Because of the rocket, Haz-Mat shipping is required.

Appearing prices of MAGNUM rescue systems DO NOT INCLUDE cords between parachute and fuselage which are SOLD SEPARATELY. During the order, the length of activating cord from parachute to fuselage must be indicated. Other parts and accessories are also available at additional cost.