YAESU rechargable batteries are intended for use with YAESU handheld transceivers.

HONEYWELL BENDIX KING® KX 155A and KX 165A TSO'd Panel-Mounted NAVCOMM Transceivers update the concept of the combined navigation and communications radio for the 21st century. With such features as programmable comm channels, support for 8.33 kHz Comm tuning (KX 165A model only), GPS QuickTune, multiple operating modes, remote channel increment with flip-flop tuning & a built-in timer, they combine a sophisticated appearance with a number of advanced capabilities including:

Programming of up to 32 Comm channels in a non-volatile memory circuit for ready recall of regularly used frequencies.

Pre-selected frequencies stored in a non-volatile memory circuit.

When interfaced to the KLN 94 GPS, both the standby Comm and Nav frequencies can be selected and remotely tuned from the GPS database.

The KX155A (a KX155 upgrade) provides access to all 200 NAV and 760 COMM frequencies, along with its optional 40-channel glideslope. In addition to its standard use, it incorporates new features including a bearing-to-station mode and a radial-from-station mode, an internal Course Deviation Indicator (CDI) for use when the external CDI is being driven by a GPS receiver, and an elapsed-time and approach timer. The KX 155A system offers 10W minimum COMM transmitter power.

The KX-165A NAV/COMM replaces BENDIX KING® KX-155, KX-155A and KX-165 NAV/COMMs which are discontinued but are still available for outright sale or in exchange for returned customer owned units in USED Serviceable or Overhauled Conditions with FAA 8130-3 Form certification. The letters "SV","OH" and "EX" in the product reference numbers (SKU) indicate the condition/sale terms. 

Very similar to KX 155, the BENDIX KING® KX 165 NAV/COMM additionally incorporates an internal VOR/LOC Converter to directly drive the BENDIX KING®  KI 525A HSI (part of the KCS 55A Compass System). It can also display the current radial from the active VOR instead of the standby NAV frequency. Other features include 10 watts min transmitter power, easy-to-read, bright gas-discharge display, large, self-dimming, microprocessor- controlled gas discharge readouts and solid-state electronic tuning for fast, accurate selection of all 200 NAV and 760 COMM frequencies.

The KX 165A (-0201 model) NAV/COMM is a slide in 8.33 kHz replacement for its predecessors, the KX 155A which is discontinued and KX 165A 25 kHz NAV/COMMs (-0101 model). Completely redesigned, it features programmable Comm channels, support for 8.33kHz Comm tuning, GPS Quick-Tune, multiple operating modes, remote channel increment with flip-flop tuning and a built-in timer.

Mounting racks, connectors and manuals  for the installation of the NAV/COMMs are also offered.

For additional information please consult the Product Description section and the supplied documentation.

R.A. MILLER INDUSTRIES (RAMI) aircraft antennas cover a wide range of functions including communications, NAV antennas, GPS, ADS-B, transponder, VOR localizer, glide slope antennas, and marker beacons. They are known for their streamlined aesthetics, quality, and reliable performance. Offered in different TSO models, RAMI wire whip and rod antennas ELT (Emergency Locator Transmitter) devices are intended for use on low-speed General Aviation aircraft. 

RAMI AV-100 FAA TSO C126a Airborne ELT Antenna is a passive two frequency (121.5 & 406 MHz) whip antenna, designed for speeds up to 250 knots. Impedance 50 Ohms Nominal, VSWR (Maximum):121.5 MHz 2.0:1 / 406 MHz 1.5:1, Polarization Vertical, Pattern Omni-Directional, Connector BNC Female, Weight: 3 oz. Maximum, Color: Black.

RAMI AV-200 FAA TSO C126a Airborne ELT Antenna is a passive two frequency (121.5 & 406 MHz) whip antenna, designed for speeds up to 250 knots. It meets DO-160G, Section 8, Category U requirements for robust vibration and is qualified for installation on helicopters with unknown related rotor frequencies. Impedance 50 Ohms Nominal, VSWR (Maximum):121.5 MHz 2.0:1 / 406 MHz 1.5:1, Polarization Vertical, Pattern Omni-Directional, RF Power Capacity 10 Watts CW, Connector BNC Female, Weight: 0.19 lbs. Maximum, Max Height 24″.

RAMI AV-300 FAA TSO Airborne ELT Antenna is a passive three frequency (121.5, 243 & 406 MHz) fiberglass rod antenna, designed for speeds up to 350 knots. Impedance 50 Ohms Nominal, VSWR: 2.0:1 max at 121.5 MHz,2.0:1 max at 243 MHz, 1.5:1 max. at 406 MHz,  Polarization Vertical, Pattern Omni-Directional, RF Power Capacity 10 Watts CW, Connector BNC Female, Max Weight 9 oz, Max Height 14″.

TKM AVIONICS offers different NAV/COMM radios as slide-in replacements of legacy products from BENDIX KING and other manufacturers. The Michel MX-170 by TKM was introduced in early 1984 aiming to replace legacy BK radios such as KX-170A, KX-170B, KX-175, KX-175B type transceivers. The latest TSO'd MX170C with 760 VHF COMM channels and 200 NAV channels is designed to be electrically and mechanically interchangeable (slide in replacement) with the Bendix King KX170 and the Bendix King KX175 series of NAV/COMM radios. Like other TKM radios,the MX170C NAV/COMM has nice features and excellent performance. The dual color LED frequency displays are self-dimming, showing standby frequencies with red and active frequencies with yellow color. The channeling outputs are for 40-channel glide slope (King Glide Slope) and 200 channels (King Slip Code). The MX 170C operates on 13.75 Adc maximum current in transmit. Please refer to the attached owner manual for additional information.

In addition to their panel mounted VHF transceivers, ICOM RADIOCOMMUNICATIONS offers handheld transceivers for aviation & marine applications. Their ICOM A25 series are powerful air band handheld transceivers offered in communications only (A25C) or NAV/COM versions (A25N) with 6 watts of power and an IP57 waterproof rating. They include a large 2350mAh Li-ion battery, providing a long operating time. The easy-to-use interface and large 2.3-inch LCD display combine to provide stress-free programming and in-flight operation. Built-in Bluetooth®, GPS and VOR navigation. ICOM A25 transceivers come with Antenna, Belt Clip, Handstrap, Battery Case, Battery Pack, Headset Adapter, Power Adapter and Battery Charger. ICOM IC-M25 VHF Marine transceiver is a slim depth light weight floating marine radio, floatable into the water with  flash and sound alarms. With its IPX7 waterproof construction, the 700 mW audio output, 11 hours of battery life, buoyancy in water and many other features it can effectively serve a wide range of marine applications. For additional information please consult the Product Description section.

Air Avionics is the common brand for Garrecht Avionik GmbH and Butterfly Avionics GmbH.  VT-2000 is a modern 6.25" rack format Mode-S/ADS-B EASA Certified Transponder (EASA Approval No. EASA.21O.705) with an integrated keyboard for easy operation. It can be installed as a direct replacement for the popular Bendix-king KT76 / KT76A/C series of transponders without any changes to pre-existent wiring and mounting trays. A special mounting tray (sold separately) is available for new installations. It has an integrated internal altitude encoder (alticoder) or or can be connected to any kind of existent alticoder in the aircraft (parallel and serial).

Product Features:

Installation without adapter and modification of existing wiring harness. Just slide in into existing mounting frame of your KT-76 or KT-76A / KT-76C.

Interfaces for future applications (i.e. ADS-B, TIS)

Certification base: ETSO-2C112a, ED-73B

Output power: min. 220 Watt (Class-1) Level 2es (extended Squitter)

Internal Alticoder

Interfaces für external alticoder (serial or parallel)

Direct-GPS NMEA Interface for ADS-B, no adapter required

Transflective color TFT Display

Illuminated keyboard

GARMIN® GTX™ transponder product line includes Mode A/C and Mode S TSO'd panel mounted transponders offered in a‭ ‬wide variety of configurations to choose‭ ‬from‭, ‬depending on desired functions‭.‬ Different models are listed under separate product presentations. 

GARMIN® GTX™ 327  is a TSO-certified Mode C digital transponder. Its innovative features, proven performance and reliability bring a whole new level of transponder utility to your aircraft. Features include a solid state design, and with no warm up time, lower power consumption and much lower heat emissions for a longer service life. It provides 200 watts nominal power output and has an easy-to-read DSTN liquid crystal display which reverses the numbers out of black for optimal viewing. An innovative keypad facilitates entering a squawk code while a dedicated VFR button allows for quick-and-easy VFR squawking. Similar to the GTX™ 330 Mode S transponder, the GTX™  327 also offers several timing and display functions, including flight time, count-up and count-down timers, as well as current pressure altitude.

GARMIN® GTX™ 327 Specifications:

Solid State Digital Transmitter

Mode: A/C

Display: DSTN LCD Display

Nominal Output Power: 200 watts 

Dimensions: 6.25"W x 1.65"H x 8.73"D (15.9 x 4.2 x 22.2 cm)

Weight: 3.1 lbs. (1.4 kg)

Product includes: GTX 327 Transponder, Installation kit, Pilot's guide

The RAMI AV-10 COMM Antenna is designed for high-performance aircraft applications. It exhibits excellent electrical characteristics and incorporates an efficient aerodynamic 4-bolt mounting base. The antenna essentially matches the styling of the communication antennas currently used on most singles and light twins. The antenna is designed to operate at speeds up to 350 mph and altitudes up to 50,000 ft. It has a drag force of 2.70 lb @ 250 mph.

Product Specifications:

Application: Airborne Communications

Frequency: 118 to 137 MHz

Impedance: 50 Ohms Nominal

VSWR: 2.0 to 1 Maximum

Polarization: Vertical

Pattern: Omni-Directional

Connector: Type "BNC" Female

Max Weight: 8 oz

Max Height: 20-1/4"

RF Power Capacity: 25 Watts

The N16 split design remote-mount VHF Navigation Receiver by MGL AVIONICS belongs to a new generation of navigation receivers based on RF direct conversion technology. The N16 is identical in size to the V16 COMM radio and can be used in a simple configuration as combined NAV/COMM solution for both MGL EFIS systems using the MGL protocols or, if at least one MGL VEGA or RAZOR control head is used these heads can provide NAV/COMM data output on RS-232 that is compatible with most EFIS systems on the market. Like V16 COMM, it is a Non-TSO'd NAV receiver for use in experimental and light-sport aircraft. For stand-alone operation, at least one MGL RAZOR control head or two MGL VEGA heads are required. Using these heads a fully compliant solution is presented that provides both VOR CDI using a rotary control for OBS bearing entry as well as the familiar two bar ILS localizer and glideslope indication. The VOR provides a display for bearing to station and radial from station at the same time for up to two simultaneously-received VOR stations. For additional information please refer to the attached documentation.

GARMIN® GTX™ transponder product line includes Mode A/C and Mode S TSO'd panel mounted transponders offered in a‭ ‬wide variety of configurations to choose‭ ‬from‭, ‬depending on desired functions‭.‬ Different models are listed under separate product presentations. 

GARMIN® GTX™ 330 is a panel-mounted IFR-certified 250 W, Mode S digital transponder with traffic datalink capability and dedicated pushbutton keys for squawk code selection. The GTX™ 330 series brings ATC aircraft surveillance to new levels of precision, reliability and performance. Optionally available with 1090 MHz extended squitter transmission, certified to TSO-C166b authorization, the GTX™ 330 ES (Extended Squitter) provides an affordable pathway to ADS-B compliance for the Next Generation airspace system. The extended squitter technology enables transponders to automatically transmit traffic surveillance data (including aircraft flight ID, position, altitude, velocity, climb/descent, and heading information) compared to traditional Mode S and Mode C transponders, which can only broadcast altitude, and thus require a ground-based radar to correlate and identify the aircraft's position. In addition, simultaneous broadcast of this information to TAS or TCAS equipped aircraft, enables them to essentially see the same traffic picture for their location that ATC is watching on the ground. The ‬“ES” upgrade provides a ADS-B‭ ‬Out‭ solution but an input from an approved position source is still needed as GTX™ 330 does not have a WAAS GPS.

GARMIN® GTX™ 330 is discontinued and replaced by GTX™ 335, an entry-level ADS-B Out model‭ with a version integrating an  internal WAAS GPS. If ADS-B‭ ‬In capability is required then the the GTX™ 345 transponder should be selected.

For additional information please refer to the Product Description section.

The AV-532 is a VOR/LOC/GS receive only antenna which consists of taper ground high-strength 17-7PH stainless steel elements to reliably withstand vibration and wind loads. The insulators are weather-sealed compression-molded bakelite with the mounting holes provided. The unit may be mounted with the V pointed either forward or aft. The antenna is designed to operate at speeds up to 350 mph and altitudes up to 50,000 ft. It has a drag force of 3.42 lb @ 250 mph.

EASA Certified VHF transceiver in 160mm format with 6W output power. Automatic selection of 8.33kHz/25kHz spacing and OLED display.

The GARMIN® GTR series COMM TSO'd panel mounted transceivers (please see separate presentation) together with the GARMIN® GNC series NAV/COMM radios are replacement products for the popular SL30 and SL40 models. They include new features to reduce pilot workload, while also offering an affordable solution to meet the requirements of the 8.33 kHz channel spacing European Union mandate under the Single European Sky (SES) initiative. They are more powerful than their SL-series predecessors with 10- or 16-Watt transmit power available versions. 

The GARMIN® GNC series NAV/COMM radios are offered with either a 10 W (GNC 255A) or 16W (GNC 255B) COMM featuring a 25 kHz or 8.33 kHz spacing. Both come with a an internal VOR/LOC converter, a 40-channel glideslope (GS) receiver and include the rack, connector kit, and back plate. They are offered as units only or as kits with a 4ft harness to AUDIO Panel.  If purchased with the 4ft harness, they can only be used  in experimental aircraft.

The STRATOMASTER VEGA range instruments/indicators from MGL AVIONICS includes different 2 1/4" (57mm) microprocessor based color display instruments operating over a wide supply voltage range of 8 to 30V DC with with built in reverse and over voltage protection. They are non certified and only suitable for installation in experimental and sport  (LSA) aircraft. Using a high resolution color graphics display, these instruments/indicators provide excellent daylight readability with built in backlighting making them easy to read at night time. They include a rotary control plus 2 independent keys for easy menu navigation and to access specific instrument features. Sensors are also offered to enhance their functionality. The MGL AVIONICS STRATOMASTER VEGA Series instruments/Indicators include: Artificial Horizon & Magnetic Compass Display, Altimeter/VSI, ASI, ASI/VSI, Engine Monitoring System (EMS), Fuel Computer, Information Display, Manifold Pressure, Température, RPM, Hobbs, Universal Engine/Rotor RPM, Hobbs, 4-Channel Thermocouple (EGT/CHT), 4 Channel Universal Analog Input (Pressure/Temperature/Voltage/Current) and NAVCOM Control head for MGL N16 NAV/COMM or V16 COMM VHF.

The GARMIN® GTN 650Xi (*) GPS/Nav/Comm/MFD panel-mount platform replaces discontinued GTN 650 (**) offering more pixels, processing power, speed and performance.  It’s approved for installation in many of makes and models of fixed-wing aircraft and helicopters providing high-resolution terrain mapping, graphical flight planning, traffic target surveillance, multiple weather options, taxiway diagrams and a host of other advanced navigation features. It comes with Americas or International Database (specified at the time of ordering).

The GARMIN® GTN 650Xi features:

- a brighter, faster, sharper, better Do-It-All intuitive touchscreen interface providing quick access to navigation, radio tuning, multifunction display features and more,

- powerful fast response dual-core processors boosting the GTN Xi series graphical display capabilities — with faster zooming, panning and map rendering on the display,

- high-resolution  4.9” display with almost double the pixel count of its predecessor and wider viewing angles,

- multi-function display cpability supporting multiple inputs of moving maps, terrain, traffic, weather, airport diagrams and more,

- easy data entry with the use the on-screen QWERTY keyboard or traditional concentric knobs to enter frequencies, waypoint identifiers, routings and more,

- Telligence™ voice control technology helping reduce pilot workload by responding to hundreds of spoken commands with the press of a button on the yoke,

- finger swipe gestures enabling pilots to pan across the map display or use a smartphone-like pinch-to-zoom motion to scale up or down on any map, traffic or terrain page.

GARMIN® GTN 650Xi Specifications

TSO applicability: C34e; 2C34f; C36e Class A; 2C36f Class A; C40c; 2C40c; C74d Class A; C112e; C128a; 2C128; C146e Class 3; C151d Class A, B; C157b Class 1, 2; 165b; C169a Class C, E, 3, 4, 5, 6; 2C169a Class C, E, H2, 3, 4, 5, 6; C194; C195b Class B1, B3, B5, B7; C209

Display size: 4.9" (125 mm) diagonal

Display resolution: 834 pixels (W) x 370 pixels (H)

Unit bezel height: 2.65" (67 mm)

Unit bezel width: 6.25" (159 mm)

Unit depth with connectors: 11.25" (286 mm) (measured from face of aircraft panel to rear of connector backshells)

Unit weight: 5.5 lbs (2.48 kg)

Input voltage range: 11 VDC - 33 VDC

Operating temperature range: -20° C to 55° C (-4° F to 131° F)

Number of GPS channels: 15 (12 GPS and 3 GPS/WAAS/SBAS)

LAT/LON position accuracy: <1.25 meter RMS horizontal, < 2 meter vertical, with WAAS

Maximum velocity: 1,166 knots

Position update Interval: 0.2 sec (5 Hz)

Notes:

(*) The GARMIN® GTN 650Xi can be supplied as kit with 4 feet pigtail wire harness without certification . If cerification is required installation must be done by a GARMIN® Authoried Service Center.

(**) The GARMIN® GTN 650 can be supplied as USED (Serviceable) Certified unit (FAA 8130-3 Form) with GPS antenna, rack, connector, existing Database, 6 nonth warranty.

The Distance Measuring Equipment (DME) systems used on aircraft provide information on aircraft slant distance, ground speed, and time to a ground station. They operate in the 960 – 1215 MHz frequency band.  

HONEYWELL BENDIX KING®, a leading avionics manufacturer offers panel mounted, remote DME, DME displays outlined below as well as accesories such as racks & connectors for DME installation and connection. They are offered for outright sale or in exchange for returned customer owned units in NEW Condition or USED (Serviceable or Overhauled) Conditions. The letters "SV","OH" and "EX" in the product reference numbers (SKU) indicate the condition/sale terms.

For additional information please consult the Product Description section & the supplied documentation.

HONEYWELL BENDIX KING® Panel Mounted DME

BENDIX KING® Silver Crown Plus line of Panel Mounted 100 watt KN 62A and 50 watt KN 64 DME are self-contained, 200-channel systems, which can be channeled remotely through almost any NAV receiver or tuned directly with their own frequency selection knobs. They offer dual channeling capability with two DME frequencies available at all times (one remote & one stored internally). Also feature redesigned faceplates for improved readings' illumination, large sturdy knobs and a three-position function switch for easy operation. They operate on any 11 to 33 VDC voltage without adapters or power converters while due to their modest power requirements no external cooling is needed. 

HONEYWELL BENDIX KING® Remote DME

BENDIX KING® TSO'd KN 63 DME is a complete 100 watt, 200-channel remote DME system utilizing Large Scale Integrated (LSI) circuit technology. Offering significant advantages in DME reliability and performance, the KN 63 is all solid-state (no transmitter tubes) and can be installed with either single or dual panel DME indicators (displays) such as the BENDIX KING® KDI-572 or KDI-574. 

HONEYWELL BENDIX KING® DME Displays

BENDIX KING® TSO'd KDI-572 or KDI-574 DME Displays can be used as master display controls and  information displays from KN 63 remote DME transceiver. The top-quality KDI 572 DME displays distance, groundspeed, and time-to-station all at the same time. Slant-range distance is computed digitally and displayed up to the maximum range of 399 nautical miles. Station lock-on is typically achieved within three seconds, with accurate groundspeed and time to station computations becoming available within one minute. The KDI 572's single control switch offers easy operation of the entire DME system as well as DME channeling. It has settings for ON/OFF, NAV 1, NAV 2, and DME HOLD. Comes with an indicator for area navigation (RNAV) to let you know if the displayed distance and time are to a waypoint or a radio navigation beacon. The TSO'd KDI 574 DME display is similar to KDI-572 but DOES NOT include ON/OFF, NAV 1/2, DME Hold selector. For use with Bendix/King Remote DMEs KDM-706 / KDM-706A, KN-63 DME and KTU-709 TACAN.

HONEYWELL BENDIX KING® Panel-Mounted KLN 35A VFR GPS & KLX 135A VFR GPS/COMM with moving map. These products are DISCONTINUED and NO LONGER AVAILABLE IN NEW CONDITION.

The KLN 35A VFR GPS receiver combines satellite derived GPS worldwide navigation system with moving map graphics, a high-visibility display and and a choice of customized Jeppesen Nav Data databases, including coverage for Americas, Atlantic and Pacific areas. The KLX 135A offers even greater capability, incorporating all the same GPS performance and features as the KLN 35A also integrating a TSO'd, 760-channel, very-high frequency (VHF) communications radio with its navigation functions.

Limited Availability exists in USED devices which can be furnished in Serviceable or Overhauled conditions indicated respectively by the letters "SV" and "OH" in the product reference numbers (SKU and  accompanied by the relevant certification (e.g. yellow tag, 8130-3 form). In addition, they may be offered as exchanges / trade-ins  for returned customer owned units indicated by the letter "EX" in the SKU.  In the case of an exchange/trade-in option of a customer unit, the  full selling price of the ordered unit is charged and the core credit is refunded or credited towards future orders when our co-operating supplier verifies that the unit is in a reasonable, repairable condition. It is recommended that this option is selected by our customers mainly for upgrades and only in cases when their units are functioning properly at the time removal from the aircraft. In cases when customer units are found by our supplier to be non-repairable, the core deposit shall not be refunded and shipping charges shall apply if customers wish the return of these units to them. 

Installation parts (for new installations) and manuals are sold separately. 

Please refer to the Product Description section for technical specifications and information on USED avionics.