EXXONMOBIL® MOBIL™ AERO Series Aviation Hydraulic Fluids includes AERO HFA, HF, and HFS hydraulic fluids offered for aircraft systems where use of hydrocarbon hydraulic fluids is required. 

They are low viscosity, high VI (viscosity index) fluids with excellent low temperature properties, good anti-wear performance, and good chemical stability.

MOBIL™ AERO  HFA is a premium quality fluid that meets the requirements of the U.S. Military specification MIL-H-5606A (obsolete). It has a very high VI and is suitable for use at temperatures down to -54 ˚C (-65 ˚F). While this quality fluid is no longer used by the US Military, it is still used in some older, small private, and small commercial aircraft. It is also used in industrial and commercial equipment requiring good fluidity at very low temperatures, where MOBIL™ AERO  HFA provides long, trouble-free service over a wide range of

operating conditions.

MOBIL™ AERO HF is a premium quality fluid that is approved against the most current version of U.S. Military specification MIL-PRF-5606. It has physical properties very similar to MOBIL™ AERO HFA, and also meets “super-clean” requirements required by modern aircraft hydraulic systems. It is intended primarily for military aircraft. It is also used as a hydraulic fluid for small private and small commercial aircraft, and as a strut fluid in landing gear of large commercial aircraft. It is approved as a NATO Code Number H-515 fluid.

MOBIL™ AERO HFA and HF are composed of mineral oil base stocks and contain shear-stable VI improvers.

MOBIL™ AERO HFS is a synthetic polyalphaolefin lubricant that is approved against the most current version of U.S. Military specification MIL-PRF-83282. It does not contain a VI improver. It is designed for use at temperatures down to -40˚C (-40˚F). It provides better flammability and volatility, improved stability, but has a higher viscosity at low temperature than MOBIL™ AERO HF. It meets the “super-clean” requirements. It is intended primarily for US Military aircraft. It is approved as a NATO Code Number H-537 fluid.

For additional information please consult the supplied documentation.

CASTROL® is a producer of oils, lubricants, fluids and greases for a wide range of applications. The company aerospace product range includes  lubricants, fluids and cleaners. Acquired by BP in 1992.

The CASTROL® BRAYCO™ product range includes world-leading choice synthetic oils and greases proven to perform in extreme environments increasing the lifespan of crucial equipment and delivering reliable performance in every critical application. Offered BRAYCO™ range of products features low outgassing and low volatility lubricants designed to virtually eliminate lubricant outgassing, Perfluoropolyether (PFPE) lubricants ideal for vacuum, cleanroom and reactive chemical environments and applications as well as formulations for deep sea applications that actually absorb low levels of seawater and carry it away from sensitive components.

For additional information on CASTROL® BRAYCO™ product portfolio please refer to the brief presentations included in the Product Description section and the supplied documentation.

CHEMETALL® is the brand for the Surface Treatment global business unit of BASF's Coatings division & a leading supplier of applied surface treatment technologies for metal, plastic & glass substrates. CHEMETALL® ARDROX® brand is the leading brand for aerospace surface solutions including paint and scale removers, exterior aircraft & gas turbine engine compressor cleaners, corrosion inhibiting and non-destructive testing protective compounds for both aircraft and aero engines and materials.

CHEMETALL® ARDROX® Corrosion Inhibiting Compounds' (CIC) range includes AV 8, AV 15 (aka DINITROL AV15), general purpose AV 25, the most versatile AV 30 and AV 40.  They are water displacing, long-term corrosion inhibitors highly  penetrating  areas exposed to severe corrosion conditions and combining good penetration properties with excellent corrosion inhibiting characteristics and a low applied film weight. Their viscosity is optimized to ensure an effective protective coating and promote penetration into otherwise inaccessible areas of the airframe. Applied as a coating to protect metals in airframe structures, on painted and unpainted surfaces, and in aerospace components to safeguard metals from corrosion. In areas exposed to severe corrosion conditions AV 8 should be overcoated with AV 100D - a heavy duty, waxy, firm film CIC.

CHEMETALL ARDROX® CIC are offered in different packaging options and comply with different specifications including Boeing BMS, MIL-PRF-16173, McDonnell Douglas DMS, Airbus AIMS and others. They are classified as HAZMAT Hazardous Materials UN Number: UN1139 - UN Class: 3.

CHEMETALL ARDROX® 3140 Corrosion Preventative contains film forming agents, antioxidants and corrosion inhibitors in a refined hydrocarbon solvent base. Provides long term protection for raw materials, sub-assemblies and finished components, which are to be stored or used in corrosive environments. 

CHEMETALL ARDROX® 6367 Turbine Engine Cleaner is a liquid concentrate which consists of an aqueous blend of biodegradable surfactants and corrosion inhibitors formulated to clean the compressor sections of gas turbine engines. It is solvent free and removes deposits, oils and their oxidation products in the compressor area. Contains corrosion inhibitors providing protection against corrosion for up to 3 days during engine standstill times. Does not contain any EDTA, NTA or their salts. Regular cleaning with Ardrox® 6367 helps maintain peak engine efficiency and reduces maintenance and fuel cost. Ardrox® 6367 is compatible with recognized antifreeze materials used during cold weather cleaning. Approved for use in a range of turbine engines including CFM56 CP5060 , GE SPM 70-80-04, Ref. C04-140, P&W SPM 70-12-00, SPMC 87-10A, Rolls Royce CSS 260 and others. Offered in different packaging options including 25-liter pails and 55 USG drums.

For additional information please consult the Product Description section or the attached documentation.

The AVIATIONEU NEW ERA aviation lubricants form part of our own labelled (AVIATIONEU NEW ERA) product portfolio  and include an extensive range of piston and turbine engine oils, greases, hydraulic, coolant and other fluids used in a variety of applications in general aviation as well as commercial (transport) and military aircraft of Russian manufacturers, such as Ilyushin Mikoyan, Irkut, Sukhoi, Tupolev and Yakovlev (now merged and operating under a new company, United Aircraft Corporation), Ukrainian (Antonov), and others.

The AVIATIONEU NEW ERA lubricants are analogues and offered as cost effective alternatives to AEROSHELL®, EXXONMOBIL®, NYCO, LUKOIL®, ANDEROL®, ROYCO®, and other lubricants used in aircraft of Eastern manufacturers. Sourced from various quality producers, the AVIATIONEU NEW ERA aviation lubricants are offered in different packaging options (*) in liters or kilograms, depending on the lubricant and the producer.  OEM brands are also included in our offered product range and can be furnished through our current network of co-operating suppliers. Please refer to the supplied table(s) and presentations listing their respective products. Due to our continuously expanding list of suppliers and the respective range of offered products, certain products may not be currently listed in our Web Platform for Supplies. In this case please contact us for additional information and assistance.

An overview of offered AVIATIONEU NEW ERA AVIATION HYDRAULIC FLUIDS & PRESERVATIVES is included in the Product Description section serving as a Quick Guide. For AVIATIONEU NEW ERA engine oils and greases please refer to the respective separate product presentations. 

(*) Depending on the lubricant and the producer, AVIATIONEU NEW ERA aviation lubricants are offered in cans, pails, flanks, drums or other containers with the following indicative capacities:

 0.9kg/1L, 3.6kg /4L, 4.5kg /5L, 9kg /10L, 15.3kg, 27kg /30L, 54kg /60L, 91kg /100L, 182kg /200L.

LUKOIL® LUBRICANTS brand relates to an extensive range of lubricants serving the needs of applications in different markets worlwide, from passenger cars, commercial vehicles and small engines to aviation, marine and industrial uses. LUKOIL® LUBRICANTS portfolio includes among others motor oils, transmission, gear, compressor, turbine, gas engine, machine sideway, rolling mill, circulating, quenching oils, hydraulic and coolant fluids and greases. They are available in in different packaging options. 

A brief description of LUKOIL® lubricants  which can be furnished through our network of co-operating suppliers is included in the Product Description section. For additional information please refer to the supplied documentation or contact us.

Note: Supplied information is provided for reference only. For the selection of the suitable lubricant please observe the manufacturer's instructions.

The SWAGELOK® Company is a global supplier of a range of products including fittings, valves, hoses, regulators, medium- and high-pressure products, process instrumentation, quick-connects, measurement devices, tubing and tools, filters, sample cylinders, MPC modular systems, pre-engineered subsystems (PrESS), welding systems, leak detectors, lubricants, and sealants.

SWAGELOK® Goop™ thread lubricants reduce installation time by easing the assembly of leak-tight thread connections for a variety of metals and alloys. Oil-based BLUE Goop® thread lubricants can be used on stainless steel, steel, titanium, aluminum, and nickel based alloys for temperatures up to 400° F (204° C). Halcocarbon based PURE Goop® can be used on titanium, stainless steel, steel, and nickel based alloys for temperatures up to 350° F (176° C) while Oil-based SILVER Goop® thread lubricants can be used on stainless steel, and high temperature alloys for temperatures up to 1500° F (815° C). Offered in different packaging options: 1 oz. (29.5 cm3) tubes (PURE/SILVER Goop®), 2 oz. (59 cm3) tubes (BLUE Goop®) and 1 lb. (450 g) cans (BLUE/PURE/SILVER Goop®). According to the selected product, they resist or prevent galling. 

SWAGELOK® Snoop® liquid leak detectors detect gas leaks in hard-to reach areas. They are non-corrosive and non-flammable. Contain corrosion inhibitor for added protection. SWAGELOK® Snoop® liquid leak detectors can be used over a temperature range of 27° to 200° F (-2° to 93° C). For lower temperatures, –65°F (–54°C) SWAGELOK® Real Cool Snoop® liquid leak detectors can be used. Offered in different containers: 2 fl oz./59 ml (Snoop®), 8 fl oz./236 ml (Snoop®/Real Cool Snoop®) and 1 gal/3.8 l (Snoop®/Real Cool Snoop®).

SWAGELOK® also offers SWAK™, PTFE Tape, and PTFE-Free pipe thread sealants. For more information on SWAGELOK® products please refer to the supplied documentation. 

EXXONMOBIL® MOBIL™ SHC™ 500 Series oils include Mobil SHC™ 524, 525, 526 and 527 very high performance hydraulic oils formulated from synthesised, wax-free hydrocarbon base fluids combined with a carefully engineered super-stabilised additive system. 

They feature exceptionally high quality, wide-temperature, shear-stable hydraulic oils with controlled low-temperature pumpability properties and maximised anti-wear protection for high-pressure vane, piston and gear pumps. Their very high viscosity indexes contribute to their excellent low and high temperature performance making them an excellent choice for equipment subjected to a wide range of start-up and operating temperatures. They exhibit outstanding shear stability allowing their use in high-pressure, high-temperature operating environments for extended periods of time without the loss of critical lubrication characteristics. They reduce energy consumption by up to 6.2 percent compared to conventional hydraulic oils.

Features & Benefits of MOBIL™ SHC™ 500 Series Oils 

Design-Specific Synthetic Base Stock Extends service intervals | Cleaner systems and reduced close-tolerance valve sticking compared to conventional products | Improves filterability

Exceptional Anti-wear Reduces wear of components | Protects various metallurgy systems

High Viscosity Index Wide temperature range performance | Ensures equipment protection at cold start-up temperatures | Protects system components at high operating temperatures

Outstanding Oxidation Stability Provides long oil and equipment life extending filter life

Excellent Corrosion Protection Prevents internal hydraulic system corrosion | Reduces the negative effects of moisture in systems | Provides corrosion protection of multi-metallurgy component designs

Very Good Multi-metal Compatibility Optimizes inventory requirements

Meets a Wide Range of Equipment Requirements One product replacing several for optimization of inventory requirements and mitigation of product misapplication

Excellent Air Separation Characteristics  Reduces foaming and it's negative effects

Controlled Demulsibility Provides systems protection and lubrication where small quantities of moisture are present | Readily separates larger quantities of water

Innovative Keep Clean Properties Reduces system deposits and potential sludging | Protects critical components, improving system response and minimizing valve sticking

For additional information please consult the Product Description section.

HENKEL LOCTITE® is the world’s leading brand for adhesives, sealants and surface treatments. LOCTITE® Aerospace product portfolios include HYSOL® structural adhesives  and film systems for aircraft and composite repair, aerospace potting solutions and Freketo mold release agents for the aerospace composites industry. LOCTITE® HYSOL® Aerospace adhesives are used by all major aerospace manufacturers including Boeing Commercial Aeroplanes Group and provide superior integrity to aircraft structures without added weight and ensure durable, tough bonding in composite and metal surfaces. Structural adhesive applications include joint sealing, magnet bonding, metal bonding, multiple surface bonding, noise, vibration, and harshness (NVH), plastic and composite bonding, potting and encapsulating and others.

Manufactured by LIGHTHOUSE FOR THE BLIND INDUSTRIES (LHB), SKILCRAFT® PRO LUBE (also known as SKILCRAFT® PRO LUBE II) is a general-purpose lubricating oil preservative composed of highly refined mineral oil with additives.It is a rust and corrosion inhibitior, formulated to lubricate small arms and automatic weapons, protect them from corrosion, and displace water at low temperatures. This product is approved to Federal Specification MIL-PRF-32033 and meets Quality Parts List (QPL) No. LP-7053A. It is ideal for use within fuel systems and combustion chambers of engines, in addition to other general-purpose lubrication needs. Available Packaging Options: 12.5 oz. Aerosol Cans, Case 12X12.5 oz. Aerosol Cans, Case 16X1 US Quart Cans.

HAZMAT Information: HAZMAT UN Number:1950, Hazard Class 2.2 (Aerosol Can) – Not Regulated (USQ Can)

For additional information please consult the supplied documentation.

SKILCRAFT® PRO LUBE II EU Regulation REACH/SVHC Status

SKILCRAFT® PRO LUBE II, as a MIL-PRF-32033 specification compliant product, generally does not contain substances of very high concern (SVHC) as defined and typically restricted by the EU Regulation REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) regulation. However, as ABILITYONE/SKILCRAFT® products are sourced from a network of manufacturers with slight formula variations, product conformance to REACH/SVHC requirements for import into the European Union has to be confirmed with our supplier at the time of ordering.

CRC® INDUSTRIES is a global leader in the production of specialty chemicals for maintenance, repair and operational professionals and do-it-yourself applications. CRC® product portfolio includes an extensive range of cleaners, corrosion inhibitors, lubricants & penetrants, adhesives, appearance and specialty products serving the automotive, industrial, electrical, marine, heavy truck, hardware and aviation markets. Selected products are briefly presented at the Product Description section and additional information can be found in the supplied documentation.

HAMMONDS® Fuel Additives, Inc. is an innovative, industry leading manufacturer of fuel biocides and additives. BIOBOR® family of fuel additives includes BIOBOR® JF is the the most widely used and recommended fuel biocide and lubricity additive and the only available and approved biocide for use in aviation jet fuel while other BIOBOR® additives are extensively used in marine and other sectors.

BIOBOR® JF is the original, industry standard microbicide providing highly effective, proven dual-phase chemistry to eliminate the growth of harmful bacteria and fungi that contaminate fuel systems, clog filters, corrode metal surfaces and cause service interruptions. Non-corrosive and safer to handle than competitive biocides, BIOBOR® JF kills and prevents microbial growth in all fuel types, prevents microbial corrosion issues and filter plugging, works in both water and fuel phases for more effective kill while it adds lubricity and reduces wear scar by up to 20%. OEM approved biocide recommended for diesel and turbine engines and approved for military use (MIL-S53021A).

BIOBOR® MD Fuel Stabilizer and Detergent is a cutting edge over-the-road and marine fuel additive engineered to enhance fuel performance, increase lubricity and lower exhaust emissions. Cetane levels are raised for easier cold starting, fuel lubricity and combustion is increased, while the entire fuel system is cleaned of sludge. These advantages result in more power and torque with less fuel-related downtime and maintenance costs.

BIOBOR®  EB Alcohol free Gasoline Performance Enhancer is a specifically formulated additive for gasoline and ethanol fuel blends which helps combat the negative effects of ethanol in fuel tanks and engines while increasing engine performance, efficiency and fuel stability. It contains 2.5 times the EPA-required detergent and provides an “A” rating in NACE corrosion testing. BIOBOR®  EB supports engines' better performance and more power with increased fuel economy, while eliminating the problem of fuel phase separation. Prevents fuel phase separation and corrosion, cleans engine, injectors and valves, increases fuel efficiency, adds lubricity, protects pistons, o-rings, fuel lines and seals, stabilizes fuel for up to 18 months, provides easy start after long-term storage, 

BIOBOR® DC+Cetane Corrosion Inhibitors & Lubricity Additives are multifunctional diesel fuel conditioners offered in both summer and winter blends. They provide increased cetane, fuel stability, lubricity, detergency and water control. BIOBOR® DC+Cetane raises cetane, improves fuel economy & cold starting, reduces exhaust emissions and smoking, prevents sludge and asphaltene issues, decreases filter plugging, extends storage life of fuel, reduces injector and engine wear scar, cleans injectors, improves fuel economy, reduces power loss, disperses moisture and prevents water accumulation and corrosion.

For additional information please refer to the supplied documentation. 

CHEMETALL® is the brand for the Surface Treatment global business unit of BASF's Coatings division & a leading supplier of applied surface treatment technologies for metal, plastic & glass substrates.

CHEMETALL® ARDROX® 185 Series colorless scale/rust removers have a greater than 12.5 pH level and a relative density of 1.43. The series includes 185L, a highly alkaline concentrated solution in water containing sequestrants and 185 water soluble powder offering a strong alkaline solution containing sequestrants. They can be used to remove rust and scale from iron and steel  in immersion tanks but also oil, grease and some air-dried paints.  They will not attack or cause hydrogen embrittlement in ferrous alloys and there is markedly less tendency for re-rusting to occur than with acid pickling.

ARDROX® 185L is usually used at a concentration of 30-50% by volume in water, depending on the amount of rust or scale to be removed. This corresponds to a concentration of 200 - 375 g/L of ARDROX® 185 in water. ARDROX® 185 must always be dissolved in cold water. There will be an exothermic reaction and the solution will heat up to 50-60°C / 120-140°F. The ARDROX® 185L is applied by immersion between 82 and 93°C (180 and 200°F). Agitate with mechanical agitation, do not use air agitation.

The immersion time will vary according to the degree of contamination, light rust being removed in approximately 10 minutes while heavy rust may take about an hour. If the components are heavily contaminated with oil or grease, the life of the ARDROX® 185L  bath will be prolonged if they are first degreased (e.g. with an ARDROX 6-series product).

When used in conjunction with the adequate other ARDROX® specialties (sold separately), ARDROX® 185L can be used to remove scale from hot-end jet engine components. It can also be used for cleaning parts made of titanium.

Thorough water rinsing must take place after the use of ARDROX® 185L. If no further immediate surface treatment is to follow, the use of a dewatering and protective fluid such as an ARDROX® 3-series is desirable to give protection from re-rusting.

The ARDROX® 185L  comes in a 5-gallon and 180-liter containers while the 185 powder in 25 kg bags.

Qualifications / Approvals:

SAE - ARP 1755B ( conformance )

CFMI - CFM56

Rolls Royce - CSS244 OMat

SNECMA - DMR 70-620

GE SPMC 70-80-04

Pratt Whitney - SPMC 70-12-00

Turbomeca

For additional information please refer to the attached documentation.

ZET-CHEMIE® brand relates to a broad range of lubricants, cleaners and corrosion protection products for metal processing developed, manufactured and distributed by by ZET-CHEMIE GmbH for 30 years.

ZET-CHEMIE® water-miscible cooling lubricants are based on mineral oil-containing emulsion concentrates or mineral oil-free solutions. They have been used many years successfully for processing all kinds of materials. Their cutting and grinding oils are based on mineral or syntethic base oils and can be used in both chip and non-cutting metal machining processes. 

ZET-CHEMIE® corrosion protection products provide plants and components with the best corrosion protection depending on the application requirements.

ZET-CHEMIE® metal cleaners effectively address requirements for cleanliness of components in metalworking. 

ZET-CHEMIE® range of industrial lubricants can be used in a wide range of applications. 

HLP hydraulic oils feature good demulsifying properties, high stability against ageing and wear protection. They correspond to DIN 51524 Part 2. Available in the viscosity range ISO 2 – 150. HLP-D hydraulic oil conforms to DIN 51524 Part 2 with excellent detergent and dispersion features, plus wear protection. Available in the viscosity range ISO 68 – 150. 

CLP high-performance industrial gearbox oils are suitable for all industrial applications. They correspond to DIN 51517 Part 3. Their load stage is greater than 12. Available in the viscosity range ISO 5 – 680.

CGLP sliding track lubricating oils are suitable for tracks and guide rails. Their good demulsifying properties prevent them mixing with cooling lubricants. Correspond to DIN 51502 CGLP. Available in the viscosity range ISO 32 – 460.

VDL ZET-compressor oils with low evaporation losses and high stability against ageing conform to DIN 51506 VDL. Used in reciprocating and rotary lobe compressors according to the manufacturer’s instructions. Available in the viscosity range ISO 68 – 150. 

ZET-CHEMIE®  paraffin-based machine oils can be used for lubricating spindles in tooling machines. Transparent and resistant to oxidation. Available in the viscosity range ISO 2 – 32. 

ZET-CHEMIE® product portfolio also includes multi-purpose, fluid, bearing, high temperature and silicon greases in all NLGi classes and all container sizes from cartridges through to drums.Also car oils for petrol or diesel engines and trucks with EURO IV emission limits.

For additional information please refer to the supplied documentation.

HUNTSMAN Advanced Materials is a leading global material solutions provider with a product portfolio of adhesives, composites and formulation products meeting demanding engineering specifications and customer-specific needs across a wide variety of industrial and consumer applications. HUNTSMAN ARALDITE® adhesives and ARADUR® curing agents form part of the company epoxy systems widely accepted and used in many industries.

For over 40 years, HUNTSMAN ARALDITE® adhesives have been the adhesive range of choice in a huge variety of industry sectors ranging from aerospace to sports goods. In recognition of the diversity of today’s industrial manufacturing and the many new materials available for product design, Huntsman offers an extensive range of ARALDITE® adhesives to meet your varied and exacting needs. The ARALDITE® brand encompasses high-performance epoxy, acrylic, and polyurethane adhesives and high-performance specialty epoxy and benzoxazine resin systems. ARALDITE® adhesive covers a broad range of applications and offers both production and performance benefits to industrial, consumer and construction markets.

HUNTSMAN ARALDITE® specialty thermoset resins are supplied in liquids or solids, and in a range of viscosities, functionalities and epoxy equivalent weights for a wide range of industrial applications, while ARALDITE® specialty epoxy resins are typically based on bisphenol-A, bisphenol-F, phenol novolacs, cresol novolacs, amino phenol, methylene dianiline, cycloaliphatics, and isocyanuric acid.

HUNTSMAN ARADUR® curing agents are supplied in liquid or solid form and can be used in conjunction with ARALDITE® epoxy resins to achieve a broad range of thermal, mechanical and electrical properties. This complete line of high-performance curing agents includes reactive polyamides, polyamido amines, aliphatic amines, cycloaliphatic amines, aromatic amines, anhydrides and novolacs.

HUNTSMAN ARADUR® markets & applications: Paints & Coatings, Wind, Aerospace, Electronics, Electrical Engineering, Composites, Construction, Adhesives.

For additional information on  ARALDITE® adhesives and ARADUR® curatives please consult the Product Description section, the supplied documentation or contact us.

HENKEL LOCTITE® is the world’s leading brand and trusted choice for high-performance adhesives, sealants and surface treatments for manufacturing applications worldwide, from aircraft to furniture. LOCTITE® product portfolios includes an extensive range of adhesives, sealants, surface treatments, and other industrial chemicals exploiting different technologies including acrylic, anaerobic, cyanoacrylate, epoxy, hot melt, silicone, urethane, and UV/light curing technologies.These technologies combined with innovations result in product solutions for adhesives, sealants and functional coatings that are essential to countless industrial applications. 

HENKEL industrial sealant applications extend from automotive, electronics, aerospace, metal, and durable goods, to consumer goods, maintenance and repair, and packaging industries. In addition to LOCTITE® product lines, HENKEL also offers an extensive poduct portfolio under TEROSON®  brand providing bonding, sealing, coating, acoustic, stiffening and reinforcing solutions for OEM transportation assembly, vehicle repair and maintenance (VRM) , industrial assemblies and building industry applications. The TEROSON® brand represents a global and scalable technology, offering extensive market and application competence for innovative, reliable and complete systems solutions tailored to customer needs, using a wide range of technologies in the form of foams, foils, tapes, patches, extrusions, baffles, membranes, and pumbable/sprayable gels and liquids.

In Aerospace, HENKEL LOCTITE® product portfolios (listed separately)  include HYSOL® structural adhesives and film systems for aircraft and composite repair, aerospace potting solutions and Freketo mold release agents for the aerospace composites industry. LOCTITE® HYSOL® Aerospace adhesives are used by all major aerospace manufacturers including Boeing Commercial Aeroplanes Group and provide superior integrity to aircraft structures without added weight and ensure durable, tough bonding in composite and metal surfaces. Structural adhesive applications include joint sealing, magnet bonding, metal bonding, multiple surface bonding, noise, vibration, and harshness (NVH), plastic and composite bonding, potting and encapsulating and others.

Several HENKEL LOCTITE® and TEROSON® products are included in this listing and briefly described in the Product Description section. For LOCTITE® HYSOL® Aerospace products please refer to the respective product presenatation.

For additional information please consult the supplied documentation or contact us for non listed items.

McGEAN CEE-BEE™ and HONEY BEE™ Lavatory Maintenance product portfolio includes CEE-BEE™ extensive range of cost-effective top-performing cabin cleaners, deodorizers and fresheners available in a variety of formats and HONEY BEE™ toilet system cleaners, the most effective in the industry in removing scale and organic deposits in both vacuum and recirculating toilet systems. Their use results in clean, well-maintained lavatory systems ensuring reliability, preventing costly flight delays and delivering a pleasant, fresh-smelling environment for travelling passengers. Their waste line, tank & component cleaners are ideal for the maintenance, overhaul and repair of aircraft lavatory systems and component parts. They meet OEM and AMS specification requirements. Respective product lines include:

HONEY BEE™ 60 & 60NP acidic liquid aircraft lavatory cleaners, the first developed for removing hard water scale from vacuum and recirculating toilet systems and the second for removal of hard water scale and accumulated waste materials from toilet systems in aircraft. Both are thickened for better cling on vertical surfaces and can be used for removal of stains from stainless steel. They can be applied directly to scale deposits for local cleaning, eliminating the need for removal of toilet systems. Safe on stainless steel, most plastics and good quality paint.

HONEY BEE™ 60T and 60 TNP, acidic liquid cleaners, the first developed for removal of hard water scale from vacuum toilet system lines, lavatory holding tanks & components in immersion tank applications and the second for removal of hard water scale and accumulated waste materials from vacuum toilet systems in aircraft, preventing waste line clogs. Both can be applied directly to scale deposits in toilet bowls for spot removal and they are safe on stainless steel, acrylic plastic and good quality paint. 60 TNP effectively removes stains from stainless steel lavatory components, titanium waste lines and waste holding tanks. Approved for use with the Cee-Bee® Vacuum Cleaning Kit. Surfactants biodegradable.

Product lines for Lavatory Deodorants, Fresheners & Cleaners include:

CEE-BEE™ Aerofresh 35 Concentrated Lavatory Deodorant & Cleaner

HONEY BEE™ 20C  Highly Concentrated Lavatory Cleaner & Deodorizer

HONEY BEE™ 24 - Powerful aircraft lavatory deodorant 

HONEY BEE™ 26 - Cleaner & Deodorizer for Aircraft Lavatories 

HONEY BEE™ Deodorant Pak 44 -Powerful aircraft toilet deodorant

HONEY BEE™ Aerogel “Sparkle” Air Freshener

HONEY BEE™ Freshener 50 - In-Flight Liquid Cleaner & Deodorizer

HONEY BEE™ Freshener Soak 50C - Lavatory Deodorant

HONEY BEE™ 90 Aircraft Interior Surface Cleaner & Deodorizer

HONEY BEE™ 90 RTU General-Purpose Aircraft Interior Cleaner & Deodorizer

For additional information please consult the supplied documentation.

ANDEROL® ROYCO® brands  of LANXESS Corporation are global leaders in lubricants with a diverse portfolio of engine, turbine,marine oils, gear,pump and bearing oils, greases, hydraulic, compressor, aviation, finished, metal working and general industrial fluids, specialty and Mil-SPEC lubricants and base stock. ROYCO® hydraulic, coolant & other fluids are offered in different packings (1 US quart cans, carts of 24 1 US cans,5 USG pails,55 USG drums, etc.).

ROYCO® 308CA  General purpose, Water-Displacing Lubricating Oil and Preservative. Meets all requirements of MIL-PRF-32033.

ROYCO® 602 Cooling Hydrogenated Polyalphaolefin Syn Hydrocarbon Fluid. Composed of a highly branched, compact and very stable synthetic hydrocarbon (polyalphaolefin,PAO). 

ROYCO® 634E Advanced Weapons Cleaner, Lubricant & Preservative. Meets MIL-SPEC MIL-PRF-63460 rev. F.

ROYCO® 756/756A Mineral Oil Based Hydraulic Fluid for Aircraft, Missiles and Ordnance.

ROYCO® 757 Low Viscosity Mineral Based Fluid for use as an operational fluid for missile systems, aircraft, and Unmanned Aerial Vehicles (UAV).

ROYCO® 770 Synthetic Fire Resistant Hydraulic Fluid. Super clean synthetic hydraulic fluid for use in tank and howitzer recoil mechanisms and hydraulic systems, snow removal, earth moving and heavy duty construction equipment, and industrial robotic hydraulic systems.

ROYCO® 782 Synthetic Fire Resistant "Super Clean" Hydraulic Fluid for severe duty military and industrial equipment.

ROYCO® 783 Mineral Based Preservative Hydraulic Fluid recommended for use in aircraft, missile, and ordnance systems using synthetic sealing material as well as heavy duty construction equipment, and industrial robotic hydraulic systems.

ROYCO® 950 Calibration Fluid specifically curated for fuel system components used in both reciprocating and gas turbine aircraft.

ROYCO® HF-825 Acryloid Synthetic Assembly Fluid & O-Ring Lubricant.  A concentrated solution of methacrylate polymer in synthetic diester based oil providing lubricity, and a "tacky" film.

ROYCO® LGF Landing Gear & Strut Fluid. A mineral oil based hydraulic fluid designed specifically for use in aircraft landing gear systems shock struts and other fluid dampening systems. 

ANDEROL® ROYCO® and NYCO oils, greases, fluids and specialty products are used in aircraft of Russian and Ukrainian manufacturers meeting the corresponding specifications. Most of their products are included in our offered product range and can be furnished through our current network of co-operating suppliers. Please refer to the supplied table(s) listing their respective products. Due to our continuously expanding list of suppliers and the respective range of offered products, certain products may not be currently listed in our Web Platform for Supplies. Please contact us for additional information and assistance.

EASTMAN SKYDROL™ Aviation Hydraulic Fluids were developed to meet the requirements established by manufacturers and backed by recognized experts in phosphate ester technology. SKYDROL™ was the first fire-resistant hydraulic fluid in the industry and today remains the most advanced aviation hydraulic fluid. SKYDROL™ aviation hydraulic fluids include:

SKYDROL™ PE-5,  a Type V, fire-resistant hydraulic fluid offering the longest fluid life of any phosphate ester fluid available today, even under high moisture conditions. Key benefits include less frequent fluid replacement, reduced disposal volume and lower environmental footprint. Meets BMS3-11P Type V, Grade A & C specification.

SKYDROL™ 5, a lighter-weight hydraulic fluid due to its lower density resulting in fuel savings.  SKYDROL™ 5 is the first aviation hydraulic fluid demonstrating erosion-resistance at higher temperatures leading to decreased maintenance and downtime. Meets BMS3-11P Type V, Grade B & C specification.

SKYDROL™ LD-4, the world’s best-selling Type IV aviation hydraulic fluid, featuring low density, valve erosion prevention, and deposit control. Erosion resistance is made possible by a breakthrough anti-erosion additive and acid scavenger included in the formulation. Meets BMS3-11P Type V, Grade B & C specification.

SKYDROL™ 500B-4, the only commercially available standard-density aviation hydraulic fluid offering additionally improved erosion resistance, as it contains the same anti-erosion additive and acid scavenger as LD-4. Meets BMS3-11P Type IV, Class 2 specification.

For additional information please refer to the supplied documentation or contact us.

CONNTECT® produces and supplies combustion turbine fuel additives, compressor cleaners & wash systems and related products. CONNTECT® gas turbine compressor cleaners include CONNTECT® 5000, 6000, 7000 and CONNTECT® AF-100 anti-icing fluid for use with all CONNTECT® compressor cleaners. They are suitable for both ON LINE and OFF LINE use while ceaners can be injected directly into the compressor while the turbine is operating ON LINE extending periodic OFF LINE cleaning intervals and reducing average power loss. Available in 5-gallon pails, 55-gallon (208-liter) drums and 330-gallon re-usable and disposable bulk containers (totes).

CONNTECT® 5000 - concentrated water based gas turbine compressor cleaner specifically designed to remove deposits commonly found on gas turbine compressor blades.

CONNTECT® 6000 - concentrated non-toxic high performance low foam water based gas turbine compressor cleaner with cleaning efficiency similar to solvent-based cleaners.

CONNTECT® 7000 - concentrated solvent-based gas turbine compressor cleaner. The combination of non-ionic surfactants, emulsifiers and organic solvents is specifically designed to remove deposits commonly found on gas turbine compressor blades including carbonaceous deposits, oil, grease and soot. It should not be used undiluted.

The ash free ingredients in CONNTECT® cleaners have been carefully selected to ensure that no incremental trace elements can contribute to corrosion of the hot section of the gas turbine, while they contain special inhibitors to ensure compatibility with aluminum, nickel, nickel-cadmium, stainless steel, titanium and common coatings including painted surfaces and elastomers. They can be generally mixed at 1 part cleaner to 4 parts water but the method of injection and total amount of cleaning solution required differs for ON LINE and OFF LINE cleaning.

CONNTECT® AF-100 is a superior quality, specially designed propylene glycol based gas turbine anti-icing fluid for use with all CONNTECT® compressor cleaners. It is non-hazardous, non-toxic and biodegradable. High purity, ash free product insuring no incremental contamination of the hot section of the turbine.  Depending upon the percentage of AF-100 used, the freezing temperature of the cleaning or rinsing solution can be reduced down to -22 deg. F (-30 deg. C). However, its viscosity increases significantly at cold temperatures should not be mixed with cleaner or water when the  product is very cold.

AEROSHELL® brand relates to one of the most comprehensive and proven ranges of aviation lubricants in the aviation lubricants market worldwide. AEROSHELL® lubricants include aircraft piston and turbine engine oils, airframe and wheel-bearing greases, hydraulic fluids,  preservatives and other fluids. AEROSHELL® aviation lubricants are available in in different packaging options such as 55 gallon drums, 5 gallon pails, 1 US quart cans and cartons with 24 1 US cans each. A brief description of AEROSHELL® aviation lubricants is included in the Product Description section. Some of AEROSHELL® lubricants are already offered through our Web Platform for Supplies. Others, not currently listed, can also be furnished through our network of co-operating suppliers. For more information please refer to the supplied brief product catalogs and product descriptions,  the individual product presentations and corresponding documentation or contact us.