RAY ALLEN (RAC) R2S Rocker Switch provides a very positive snap action in 2 directions and returns to a center off position. It was designed specifically for Ray Allen trim systems. It is wired to connect both power leads to ground when the rocker is released. This eliminates motor coasting and allows very precise trimming. The RS2 switch is rated at 1amp. The faceplate measures 1.75" (44mm) x 1.0" (25mm) x 1.47" (37mm) deep. Self adhesive labels are not included. Sold separately.

The RAY ALLEN Trim Systems are trim servos of flight surfaces offered with different travel options designed specifically for experimental aircraft. RAY ALLEN servos are small enough to fit in individual control surfaces or can be used with lighweight springs acting directly on the control system. They come with RS2 rocker switches,  RP3 LED indicators and a RC8-7 clevis/pushrod kit. All RC ALLEN indicators operate off of feedback sensors located inside the servo. These feedback sensors are purposefully isolated from the power supply to the servo motor to guard against possible electronic failure.  Different servos are available:

T2-7A Trim System with a  .7" (17mm) travel

T2-10A Trim System with a  1.0" (26mm) travel

T3-12A Trim System with a 1.2" (31 mm) travel

T4-5 Trim System with a .5 inch (13mm) travel. This servo does not have a compatible indicator.

Technical Specifications as follows (RAC  Model / Output Shaft Movement / Travel Time):

T2-7A /  0.7 in. / 10 sec.

T2-10A / 1.0 in.  / 16 sec.

T3-12A /  1.2 in.  / 19 sec.

T4-5 / 0.5 in. / 15 sec.

The RAY ALLEN (RAC) RP4 LED position indicator is designed to be installed in the cockpit providing an indication of the servo output shaft position. This indicator supercedes and it is a direct replacement for previous RAC RP3. The RP4 indicator uses ten LED lights to show the position of a actuator output shaft (or position sensor arm). There are also two amber colored LED's, one on each end of the indicator scale, to act as a reference for the green indicator light, especially in dark conditions. The 10 LEDs are the brightest available for superior visibility in sunlight, but can be dimmed for night flight. It can be installed horizontally or vertically. 

The RAC RP4 position indicator is panel mounted using a faceplate and two countersunk, 2-56 x 7/16" screws (two spare finishing screws are included). The distance between the screw holes is identical to the older Ray Allen RP3 LED indicator. Although the faceplate dimensions are identical between the RP3 and RP4 indicators, the panel cutout size is slightly different between the RP3 and RP4. If you are replacing and older unit with a new RP4, you will only need to increase the size of your panel hole. The RP4 faceplate will cover the older RP3 panel hole.The RP4 faceplate measures 1.75"(45 mm) X .75"(19 mm) and it is 1.6"(41 mm) in depth. It is now the standard position indicator included in Ray Allen trim systems, or can be purchased separately for special applications such as a cowl or wing flap indicator.

The RP4 includes a RP4-L1 label (featuring Elev1, Elev2, Ail, Rudder, Flaps). A RP4-L2 label (featuring Cowl Flaps, < >, on/off) is also available and is sold separately. 

NOTE: Labels can only be ordered together with . In ordering these high quality labels please be advised that rocker switches and needle indicators require a large label, LED indicators use a small label. Can be only included in orders of respective RP4 position indicator(s) (not separately).

The G3 Series Stick Grips by RAY ALLEN COMPANY (RAC) includes four different models: G301, G303, G305 and G307. All feature four individual SPDT momentary contact switches to control one or two axis electric trim. The switches are triggered via a traditonal 4-way "hat" type activator. These switches are high quality with 15 amp Honeywell microswitches for their superior tactile characteristics. The slotted one or two axis faceplates also adds to the very positive switching action. The four trim switches can be wired directly to Ray Allen servos, eliminating the need to wire relays in the trim system when one grip is used. However, if two grips are used, either relays or a switch to transfer the control of trims from one grip to the other will be needed. The hand grip itself is made out of a very strong BASF composite that has excellent UV resistance. The entire grip has a textured finish. The G3 grips are 6.5” (165 mm) tall. All G3 grips feature a momentary contact, SPDT Push-To-Talk (PTT) switch located on the front side of the grip. A black faceplate is included with each grip. Gray and tan faceplates are also available. All Ray Allen  Stick Grips are designed to fit any stick size up to 1 1/8” in diameter with the use of spacers. Three spacers will be included with each grip enabling easy installation on 3/4”, 7/8” and 1” sticks. The stick grips include pre-cut and stripped 26 gage teflon insulated 19 strand wire. A die-cut label sheet with 50 different labels is supplied with all G3 grips. The labels are lexan coated for long service life and fit in their own recesses for a professional appearance.

All G3 Series Stick Grips feature:

- four individual SPDT momentary contact switches to control one or two axis electric trim. The switches are triggered via a traditonal 4-way "hat" type activator. The four trim switches can be wired directly to Ray Allen servos.

- high quality switches with 15 amp Honeywell microswitches for superior tactile characteristics. 

- slotted one or two axis faceplates. A black faceplate is included. Gray and tan faceplates are also available. 

- the G301 comes with a PTT switch and blank faceplates

- the G303 has two trim switches, a faceplate slotted vertically for one-axis trim and a PTT switch

- the G305 stick grip has four trim switches, a faceplate slotted vertically and horizontally for two-axis trim and a PTT

 -the G307 stick grip has four trim switches, a faceplate slotted vertically and horizontally for two-axis trim, a PTT switch and two additional SPDT momentary contact pushbutton switches. The pushbutton switches can be replaced with four different style toggle switches.

SWIFT AIRCRAFT manufactures Swift two-seater low wing composite aircraft with striking elliptical wings and double curvature surfaces. Comfortable, safe and environmentally sound they are designed and manufactured entirely in the UK, and available globally,

The company also manufactures Swift aircraft gauges specializing in precision-engineered gauges, including Exhaust Gas Temperature (EGT) and Cylinder Head Temperature (CHT) gauges, commonly used in aviation.