SKY-TEC, a HARTZELL ENGINE TECHNOLOGIES brand, includes starters and support for Prestolite, Electrosystems, Lamar and Kelly designs. SKY-TEC OEM contactors are today installed in many general aviation aircraft while SKY-TEC FAA-PMA contractors can be used for starter, battery master/auxiliary or auxiliary power applications in replacement of OEM parts.

SKY-TEC STS-S Series FAA-PMA certified aircraft starter solenoids (aka relays) are intermittent duty suitable for starter applications. They are available in 12V (STS-S12) or 24V (STS-S24) versions. Activation: +V to S-Terminal (Frame is grounded by mounting).

SKY-TEC STS-M Series FAA-PMA approved Battery/Master solenoids are continuous duty solenoids intended for use in battery master/auxiliary applications in certified aircraft. They are available in 12V (STS-M12) or 24V (STS-M24) versions. Activation: -(Ground) to S-Terminal. (Floating ground frame).

SKY-TEC STS-A Series FAA-PMA approved solenoids are continuous duty and typically used for connecting auxiliary (ground) power. They are available in 12V (STS-A12) or 24V (STS-A24) versions. Activation: varies.

Product Features:

FAA-PMA Certified

All-metal case construction

Silver contacts (vs. copper) for high-current capability and long-life. They provide 300A in-rush capability. Much higher than the original units.

Strong spring and high-current coil for quick contact opening - minimizing arcing

Single coil terminal (other end connected to case)

High quality manufacturing 

Upgraded to perform best with today's lightweight, high torque starters

Same OE terminal layout simple to install

For additional information on different SKY-TEC series of slenoids and their applications in different aircraft please refer to the respective product presentations.

FINDER 66 Series 30 A Power relays are electromagnetic devices available in DPDT (66.22/66.82) and DPST-NO versions (66.22-x300/66.82-x300) & different variants.

Product Features:

• Reinforced insulation between coil and contacts according to EN 60335-1

• 8 mm creepage and clearance distances

• AC coils & DC coils

• Cadmium Free option available

• ATEX compliant (EX nC) options available

Double Pole Double Throw (DPDT) Changeover (66.22 and 66.82). Commonly used to separate two circuits electrically and connect them magnetically. They are often used to interface an electronic circuit, which works at a low voltage to an electrical circuit which works at a high voltage. 

66.22 type with 30 A rated contacts, PCB mount and bifurcated terminals

66.82 type with 30 A rated contacts, Flange mount and Faston 250 connections 

Double Pole Single Throw Normally Open (DPST-NO) (66.22-x300 and 66.82-x300). Equivalent of 2 SPST switches (NO Normally Open and NC Normaly Closed) and can be used to switch 2 different loads.

66.22-x300 type with 30 A rated contacts, PCB mount and bifurcated terminals

66.82-x300  type with 30 A rated contacts, Flange mount and Faston 250 connections 

INTERCONNECT SOLUTIONS COMPANY (ISC) is a manufacturer of cables, cable assemblies, harnesses, and control panels which are used in a wide range of applications in Commercial and Military Aircraft, Lifesaving Medical Devices, Weapon Systems, Inflight Entertainment and Power Systems. The company is a supplier of Boeing and Airbus for their commercial aircraft. 

Since its introduction in 1994, the B&C SPECIALITY PRODUCTS BC320 Starter for Continental engines has established an impressive service record as the ONLY starter design on the market that has provided reliable, long-term service for these engines. 

Suitable for installation on Continental engines (C-75, C-85, C-90, C-145-2, O-200, IO-240, O-300-A, -B, and -C, and GO-300-A, -B, and -C) it solves all the problems that other starter designs have had:  worn-out clutches, broken pinions, nagging oil leaks, and catastrophic failure modes. Featuring the durability of all-steel gears and heavy-duty ball-bearings, and the efficiency of a high-torque series-wound motor, it provides greater starting torque, while saving 4.3 to 5.2 lbs. over the old key-type and pull-cable type starters (respectively).

The B&C SPECIALITY PRODUCTS BC320 Starter is STC-PMA approved for use in certificated aircraft, and is available with or without the STC (*). Two installation kits are also available:  one for replacing a key-type starter (Installation Kit 501-1), the other for replacing a pull-cable type starter (Installation Kit 501-3). For key-type starters, before installing the BC320, you will need to remove the needle bearing pressed into the engine case & install the supplied plug in its place. For pull-cable starters, before installing the BC320, you will need to cut off the 9/16 steel shaft that is installed in your engine case.

Other versions of BC320 Starter for 12v and 24v electrical systems (BC320-2, 12v Counter-Rotating or the 24v BC320-3) are also available.

(*) For the issue of the STC, the aircraft make and model, aircraft registration and serial number are required.

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different spark plugs and plug connector are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

SUPERIOR PANEL TECHNOLOGY (SPT) has developed a brighter, more uniform and longer lasting glare shield lighting system. The 18” x 1” glow strip electroluminescent lamps provide a beautiful fluorescent-like aviation green or a white light output. The ultra-thin lamps (.065 including the adhesive backing) are very flexible and conform to the curves of the underside of the glare shield. The SPT Glow Strips meet the FAA 23.853 burn test. Inverters are included with the kit. They are offered with or without a dimmer. The recommended dimmer for the strips is the Pulse Width Modulating (PWM) dimmer by SPT. Optional 14V or 28V battery back-up systems are available and recommended. SPT offers LIFETIME warranty on the Glow Strip lamps and 5-year warranty on the PWM dimmers.

SUPERIOR PANEL TECHNOLOGY (SPT) Glow Strip Product Range:

Green

GS1-18-14G Single Glow Strip-14V

GS2-36-14G Two lamp Glow Strip-14V

GS2-36-28G Two lamp Glow Strip-28V

Green with PWM Dimmer without off switch on dimmer 

GS1-18-14GPWM Single Glow Strip-14V

GS2-36-14GPWM Two lamp Glow Strip-14V

GS2-36-28GPWM Two Lamp Glow Strip-28V

Green with PWM Dimmer with off switch on dimmer  

GS1-18-14GPWMS Single Glow Strip-14V

GS2-36-14GPWMS Two lamp Glow Strip-14V

GS2-36-28GPWMS Two Lamp Glow Strip-28V

White

GS1-18-14W Single Glow Strip-14V

GS2-36-14W Two lamp Glow Strip-14V

GS2-36-28W Two lamp Glow Strip-28V

White without off switch on dimmer

GS1-18-14WPWM Single Glow Strip-14V

GS2-36-14WPWM Two lamp Glow Strip-14V

GS2-36-28WPWM Two Lamp Glow Strip-28V

White with off switch on dimmer

GS1-18-14WPWMS Single Glow Strip-14V

GS2-36-14WPWMS Two lamp Glow Strip-14V

GS2-36-28WPWMS Two Lamp Glow Strip-28V

Battery Back-Up

BP14V Battery-Back Up 14V

BP28V Battery-Back Up 28V

Surface Acoustic Wave (SAW) devices are components that make use of the ability of piezoelectric materials to convert acoustic (i.e. mechanical) waves into electromagnetic signals, and vice-versa. By far, the most common SAW devices are those which perform a filtering operation, also known as SAW filters. SAW Band Pass Filters (SAW BPF) sort signals by frequency the most widely used substrates being quartz (SiO2), lithium niobate (LiNbO3) and Lithium tantalite (LiTaO3) that are very brittle materials.

Usually SAW filters operate from 600 MHz to 2 GHz frequency range in mobile environment. Based on IF (Intermediate Frequency) and RF (Radio Frequency) filtering, there are two types of filters, IF SAW and RF SAW filters. In addition, based on construction, there are different  types of offered SAW filters such as IIDT, DMS and ladder.

Main advantages or benefits of SAW filters include:

• they allow electro-acoustic coupling via the transducer

• SAW velocity is 105 times less than that of Electromagnetic (EM) wave. As a result, SAW filters can be used in cases where EM wave based filter designs are impractical to be developed

• SAW filters are less expensive compared to BAW (Bulk Acoustic Wave) filters

• SAW filters are easy in fabrication due to easy access to their structure from the above surface of the filter.

The selection of the right SAW filter for an intended application is based on significant parameters like those listed below. Such filters are produced by different manufacturers such as TAI-SAW, Qualcomm, API, Golledge Electronics, Oscilent, Amplitronix LLC, Vectron, Filtronetics, Microsaw, SAWTRON and others.

• RF or IF type

• RF center frequency

• Bandwidth

• Pass band ripple (dB)

• Power handling capability

• Insertion loss in pass band (dB)

• package type and dimension

Please refer to the specifications of offered SAW filters, the supplied documentation or contact us for additional information.

A complete spark plug gapping solution for field or bench use by AIRCRAFT TOOL SUPPLY COMPANY (ATS). Includes the Heavy Duty Spark Plug Gapping Tool to accurately set your spark plug gaps to within 0.001". Also included is an Electrode Erosion Gauge to make sure that your gapped plugs are still in serviceable condition.You also get a set of wire feeler gauges to verify gap size. In case of an accidental over-gap of the plug, the included Gap Expansion Tool will get you back on track. Compatible with all Champion, and AutoLite Massive Electrode Spark Plugs. The complete kit includes:

1 X Gapping Tool

1 X Feeler Gauge

1 X Erosion Gauge

1 X Gap Expansion Tool

TYCO ELECTRONICS TE CONNECTIVITY™ SOLISTRAND Series Terminals & Splices are specially designed to terminate solid and stranded wire, irregular-shaped conductors, and wire-conductor combinations while still retaining the superior performance characteristics of single-purpose terminals and splices. The series resists corrosion and vibration, and the tensile strength is well within the limits of commercial and military specifications. TE Connectivity offers SOLISTRAND crimping tools to ensure terminations are consistent and uniform for easier quality control and reliable performance. The TE SOLISTRAND line includes terminals, parallel and butt splices, flat rings, spades, hooks, and flanged tongue terminals in sizes from 26AWG (0.1mm2) through 600 MCM (304mm2).

Features & Benefits

SOLISTRAND terminals and splices are constructed of fine grade high conductivity copper for optimal electrical performance

The brazed seam increases metal strength around the entire barrel area assuring withstanding harsh industrial environments. It also prevents pinched and stubbed wires

The “W” crimp – two longitudinal crimps – and the dimples or serrations inside the wire barrel  offer maximum electrical contact area after crimping and higher tensile strength. This permits the use of a shorter barrel, which end up in a smaller form factor and makes it more cost effective

Bell mouth on barrel entrance makes insertion of wires easier and reduces installation time and increasing production yield

Most SOLISTRAND terminals and splices meet or exceed the requirements of SAE AS7928, Type I, Class 1 and 2. Aircraft-, defense- and marine (related) equipment base their performance requirements on AS7928

Rated for up to 170°C maximum and therefore suitable in all standard applications.

Applications

Pad- and pole-mount transformers

Power supplies

Motors

Switchgear

Telecommunications

Appliances

Panel boxes

Heavy equipment

Instruments/control

Transportation

For additional information please refer to the supplied documentation.

Bi-metallic single toggle thermal circuit breakers suitable for homebuilt aircraft. Used as original equipment in Beech, Cessna and Piper aircraft. 0.5 amp to 50 amp ratings may be used as on/off switch. Maximum operating voltages: 32 VDC and 250 VAC (to 400 Hz).

Product Features:

Lightweight, less than 2 oz.

0.5 amp to 50 amp ratings may be used as on/off switch.

Cannot be reset against overload.

Screw termination.

Trip-free operation.

TYCO ELECTRONICS TE CONNECTIVITY™ ARINC 600 Connectors feature a stamped and formed contact system versus the traditional, screw machined contact system. Available in either Solder Tail or Press-fit (eye of the needle) designs.

Being the first to offer size 22 contacts in a press-fit PCB attachment style, their ARINC 600 product portfolio now includes press-fit size 20, 16 and 12 power contacts, as well as press-fit Quadrax contacts providing a total press-fit PCB-attach connector solution.

TE CONNECTIVITY™ ARINC 600 Connectors feature a lighter design for considerable cost savings. The stamped system allows for selective gold plating to only critical socket contact tines instead of the whole contact, decreasing gold plating costs. By changing to hollow contacts instead of the solid contacts in the legacy design, this product design reduces weight by up to 10% (depending on insert arrangement) and includes backward compatibility. All these with the same high levels of performance and reliability.

Features & Benefits

Completely inter-mateable with existing ARINC 600 plug connectors

"Monoblock" single-piece inserts that simplify the manufacturing process, cut costs

Stamped and formed, selectively plated size 22 contacts provide substantial cost savings while delivering excellent performance and reliability

Equivalent electrical performance vs. current design

Available in either Solder Tail or Press-fit (eye of the needle) designs

Up to 10% weight savings per connector (depending on insert arrangement)

Applications

• In-Flight Entertainment

• In-Flight Networks

• Flight Controls and Communication

• Military Ground Vehicles

For additional information please refer to the supplied documentation.

Note: TYCO ELECTRONICS TE CONNECTIVITY™ ARINC 600 Connectors are Special Order items and therefore Non-Cancellable/Non-Returnable Upon Order Placement (NCNR). Minimum Order Quantities & long lead times usually apply. Please contact us. 

The 317 type IC voltage regulators are adjustable 3-terminal positive voltage regulators capable of supplying in excess of 1.5 A over an output voltage range of 1.25 V to 37 V. Unlike other IC regulators designed to provide a fixed output voltage, 317 type IC voltage regulators are widely used adjustable positive voltage regulators available in many different packages intended for surface mounting on circuit boards. They are exceptionally easy to use and require only two external resistors to set the output voltage. For getting a stable output the input voltage must be 2 to 3 volt higher than the output.

The 317 type IC voltage regulators are offered by different manufacturers and can be used in commercial equipment and a variety of other applications including but not limited to those where there is a need for an  adjustable regulated power supply circuitry in a single chip providing 1.2V to 37V DC output voltage with up to 1.5A output current capability and very low external components. Furthermore, they also include many other features like short circuit protection, safe area and over heat protection making them essentially blow-out proof and long term performers. 

Product Features / Technical Specifications

Output current in excess of 1.5 Amps

Output voltage adjustable between 1.2V and 37V

Floating operation for high voltage applications

Internal thermal overload protection

Require low external components

Require only two external resistors for output adjustment

Capable of short circuit protection

Over heat shutdown function

Output transistor safe-area compensation

Standard 3-lead transistor packages

Low price

Reliable to use in commercial applications

Maximum input voltage is 40V DC

Low standby current

Indicative Applications

Voltage step down circuits

Lab power supplies

Battery Chargers

Solar Power Supplies

Microcontroller Related Applications

DC to DC converters

Portable Instruments

For additional information please refer to the supplied documentation.

Note: Depending on the availability of the above mentioned product/part at the time of order implementation, alternative products/parts may be supplied of equivalent features and specifications, subject to the prior notification and approval of the buyer.

This external power receptacle Model 4621B is designed to mount in a hole in the skin of aircraft. Hole is then covered with hinged access door (not included). Mates with AN2551 type plugs.

This kit consists of two GE #4509 12V, 100 watt sealed beam lamps rated to draw 7.69 amps, brackets for installation, switch, switch plate, 60 ft. of 2-conductor hookup wire and instructions. Black and white wrapped 18 gauge wire can be used for installation. It is suitable for experimental / homebuilt aircraft only. No FAA approval.

Size: 4-1/2"H x 5-1/4"W x 2-1/4"D with bulbs installed. 

Military Specification MS35059 Series Toggle Switches can be used to upgrade your aircraft's cockpit controls. These heavy-duty metal switches have a standard shape that works well for a variety of applications can be used for most components that only function in either the on or off positions. They are available in several sizes to fit your particular airplane and are shipped with all necessary rings and hardware for installation. Toggle switches are available with two or three operating positions, 1 or 3 hole mounting and a variety of circuitry & electrical ratings. Contacts are made of solid silver. Wide usage is found in aircraft, mobile, marine, electronic and industrial applications. Available in full "AN" standard size & Ultra Miniature 1/2" size, contact types and circuit codes (see reference chart).

BC207 High/Low Voltage Warning Indicator by B&C SPECIALITY PRODUCTS  is a solid-state device which provides a visual indication of abnormal bus voltage via a panel-mounted warning light (included). It is intended for use in non certified aircraft. Not FAA Approved. When flashing,the warning light indicates a bus voltage greater than 15.5 volts D.C. When steady, it indicates a bus voltage below 12.5 volts D.C. The product also includes B&C S708-2 Miniature Push-Button switch (push-to-test). The BC207  Voltage Warning Indicator can be used in both 14v and 28v electrical systems. 

RIPLEY® UTILITY TOOL® WS 64 Series 5-35 kV adjustable cable strippers can be used for cable jackets & secondary & primary cable insulations.

Product Features & Specifications:

Compact, universal tool for stripping the end or mid-span on cable outer jackets & insulation materials with diameters from 0.5″ to 2.5″ (12.7 mm to 63.5 mm)

"Dual-position" jaw for removal of the outer jacket on primary power cables with all major insulation shields

Blade design provides an easy & efficient stripping operation with minimal effort, as well as a spring-loaded trigger-action jaw for quick cable diameter adjustments

Rugged, all metal construction & micro adjustable blade for a variety of jacket thicknesses (Blades are sold separately)

Material: Aluminum

Length: 8″ (200 mm)

Weight: 1.9 lb (860 g)

NOTE: RIPLEY® UTILITY TOOL® QC-2 Series Heavy-Duty Quick Clamp is a required accessory tool sold separately.

Fine quality switch from ACS used in many aircraft. The switch housing is machined from billet aluminum which makes this switch 25% lighter. It provides “ON” and “OFF” electrical control of both magnetos on a single engine aircraft. The key-operated switch mounts from the rear of the panel in a 7/8” dia hole. Available with or without starter position. A-510-2 model with starter position is supplied with switch plate two keys. (diode included). FAA PMA Approved. Made in USA.

The RAY ALLEN Trim Systems are trim servos of flight surfaces offered with different travel options designed specifically for experimental aircraft. RAY ALLEN servos are small enough to fit in individual control surfaces or can be used with lighweight springs acting directly on the control system. They come with RS2 rocker switches,  RP3 LED indicators and a RC8-7 clevis/pushrod kit. All RC ALLEN indicators operate off of feedback sensors located inside the servo. These feedback sensors are purposefully isolated from the power supply to the servo motor to guard against possible electronic failure.  Different servos are available:

T2-7A Trim System with a  .7" (17mm) travel

T2-10A Trim System with a  1.0" (26mm) travel

T3-12A Trim System with a 1.2" (31 mm) travel

T4-5 Trim System with a .5 inch (13mm) travel. This servo does not have a compatible indicator.

Technical Specifications as follows (RAC  Model / Output Shaft Movement / Travel Time):

T2-7A /  0.7 in. / 10 sec.

T2-10A / 1.0 in.  / 16 sec.

T3-12A /  1.2 in.  / 19 sec.

T4-5 / 0.5 in. / 15 sec.