Cleaners, Coolants/Anti-Freeze, Corrosion Inhibitors, Hydraulic & Other Fluids

This category includes different fluids used in aerospace and industrial applications including hydraulic oils and fluids, transmission, brake, metalworking as well as cleaners, corrosion Inhibitors and coolants/anti-freeze fluids. Such fluids are offered in  different viscosities, viscosity indices, oxidation stability, wear resistance, seal compatibility and additives to serve application requirements.

Hydraulic oils are the most common form of hydraulic fluids. Quite often these two terms are used interchangeably. However their key difference between the two is that hydraulic fluids are used in automatic transmissions in automobile systems whereas hydraulic oils can not be used for this purpose.

Coolant fluids are often used in engines (mostly automobile ones) to keep their temperatures at a regulated level. Their use today in aircraft engines is limited as most of them are air-cooled. Hydraulic fluids (or liquids) are the medium by which power is transferred in a hydraulic machinery or system. Hydraulic systems can be found today in a wide variety of applications with their major components including the reservoir, pump, valve(s) and actuator(s) (motor, cylinder, etc.). Apart from their energy transmission function, they are also used for lubrication, heat transfer and contamination control. Today’s hydraulic fluids come in different varieties, most common being petroleum-based, water-based and synthetics. 

Petroleum-based or mineral-based fluids are the most widely used fluids today. These fluids offer a low-cost, high quality and readily available selection. The properties of a mineral-based fluid depend on the additives used, the quality of the original crude oil and the refining process. Additives in a mineral-based fluid offer a range of specific performance characteristic. Common hydraulic fluid additives include rust and oxidation inhibitors (R&O), anticorrosion agents, demulsifiers, antiwear (AW) and extreme pressure (EP) agents, VI improvers and defoamants. Additionally, some of them contain colorful dyes, allowing easy identification of leaks. Water-based fluids are used for fire-resistance due to their high-water content but, apart from their higher cost compared to conventional petroleum-based fluids, they have other disadvantages (e.g. lower wear resistance) which must be considered. They are available as oil-in-water emulsions, water-in-oil (invert) emulsions and water glycol blends and used in applications when fire resistance is needed. Water-based fluids can provide suitable lubrication characteristics but need to be monitored closely to avoid problems. Synthetic fluids are man-made lubricants and many offer excellent lubrication characteristics in high-pressure and high- temperature systems. Some of the advantages of synthetic fluids may include fire-resistance (phosphate esters), lower friction, natural detergency (organic esters and ester-enhanced synthesized hydrocarbon fluids) and thermal stability.

Products in this category are sourced from quality producers, offered in different packaging options and comply with military (MIL-SPEC ) and other industrial specifications/standards to meet application requirements. In addition, hydraulic and coolant fluids and specialty products used in Russian and Ukrainian aircraft are also included. Due to our continuously expanding list of suppliers and the respective range of offered products, certain products may not be currently listed in our Web Platform for Supplies. The list below presents different MIL-SPEC products which can be furnished through our current network of co-operating suppliers and their respective specification of compliance. Please also refer to the individual product presentations or contact us for additional information and assistance.

Hydraulic, Coolant & Other Fluids

MIL-PRF-5606A Hydraulic Fluids, Aircraft, Missile, And Ordnance Petroleum Base

MIL-PRF-5606H Hydraulic Fluids

MIL-L-5606A Aviation Hydraulic Fluids

MIL-H-5606A (obs) Aviation Hydraulic Fluids

MIL-PRF-6083F Hydraulic Fluids

MIL-PRF-46170D Type 1 Synthetic Fire Resistant Hydraulic Fluids

MIL-PRF-83282D/MIL-PRF-83282D, Amd. 1 Aviation Hydraulic Fluids

MIL-PRF-17672D-32 Hydraulic Oils

MIL-PRF-17672D-46 Hydraulic Fluids

MIL-PRF-87257A Hydraulic Fluids

MIL-PRF-87252C Coolant Fluids, Hydrolytically Stable, Dielectric

BMS 3-32 Strut Fluids

BMS 3-32 Type 2 Landing Gear Fluids

Solvents

MIL-PRF-7024F Solvents

Cleaners, Coolants/Anti-Freeze, Corrosion Inhibitors, Hydraulic & Other Fluids

Active filters

SWEPCO 201 Multi-purpose...

SWEPCO 201 MultiPurpose Gear Lubricant by SOUTHWESTERN PETROLEUM LUBRICANTS LLC.is a high performance single weight gear oil formulated to ensure maximum performance in a wide range of mobile and industrial gearbox applications. It can be used as a multi-purpose gear lubricant for most manual gear boxes, stationary industrial or rolling stock. SWEPCO’s premium high VI base stocks, proprietary Lubium® II anti-oxidation/anticorrosion package and other advanced additive chemistry provide costefficient extended drain protection from wear, foaming, overheating, deposits, rust and water contamination. SWEPCO 201 Multi-purpose Transmission Gear Oil is available in different viscosities (SAE Gear Oil Grades): 80w90, 90w, 140w and 250w and different packaging options.

Swepco 201 80/90W is used mostly on automotive applications. 90w grade is used in aviation applications (e.g. as transmission oil for Robinson R22 and R44 helicopters).

For addition information on SWEPCO 201 features, benefits and applications please consult the Product Description section and the supplied documentation.

AEROSHELL® Aviation...

AEROSHELL® brand relates to one of the most comprehensive and proven ranges of aviation lubricants in the aviation lubricants market worldwide. AEROSHELL® lubricants include aircraft piston and turbine engine oils, airframe and wheel-bearing greases, hydraulic fluids,  preservatives and other fluids. AEROSHELL® aviation lubricants are available in in different packaging options such as 55 gallon drums, 5 gallon pails, 1 US quart cans and cartons with 24 1 US cans each. A brief description of AEROSHELL® aviation lubricants is included in the Product Description section. Some of AEROSHELL® lubricants are already offered through our Web Platform for Supplies. Others, not currently listed, can also be furnished through our network of co-operating suppliers. For more information please refer to the supplied brief product catalogs and product descriptions,  the individual product presentations and corresponding documentation or contact us.

AEROSHELL® Aviation...

AEROSHELL® produces a range of mineral and synthetic hydrocarbon hydraulic fluids and preservatives supporting operation and longer preservation of aircraft hydraulics. An overview of offered products is presented below. Additional information is available in the Product Description section.

The AEROSHELL® Fluid 12 is a synthetic ester oil used for general aircraft lubrication as well as for aircraft gyro instrument gimbal bearings, separately lubricated high speed turbines and compressors, aircraft air cycle equipment and electronic equipment. Particularly suitable when an oil with a low evaporation rate is required at high and low temperatures. Approved to MIL-L-6085C.

The AEROSHELL® Fluid 31 is a synthetic hydrocarbon based aircraft hydraulic fluid with greatly improved fire resistance characteristics when compared with conventional petroleum products. Approved to MIL-PRF-83282D.

The AEROSHELL® Fluid 41 is a mineral oil based  "super clean" hydraulic oil manufactured to a very high level of cleanliness and possesses improved fluid properties. It is suitable for use with brake and hydraulic systems with synthetic rubber seals.

The AEROSHELL® Mineral Fluid 5M-A is a highly refined, medium viscosity mineral oil containing an extreme pressure additive as well as additives to provide good oxidation and corrosion protection. Production of this product is discontinued. Limited availability till stock exhaustion.

The AEROSHELL® Fluid 61 is a synthetic hydrocarbon base hydraulic fluid specifically inhibited to provide excellent oxidation stability for the oil. Approved to MIL-PRF-46170 Type I.

The AEROSHELL® Fluid 602 is a synthetic hydrocarbon coolant fluid for aircraft electronics. Production of this product is discontinued. Limited availability till stock exhaustion. Consider CASTROL® BRAYCO™ 889 meeting same specification MIL-PRF-87252E.

The AEROSHELL® Fluid 71 is a preservative mineral hydraulic fluid of improved cleanliness. It is composed of a mineral base oil with an additive package which results in a product with excellent corrosion preventative properties as well as excellent oxidation stability, and good anti-wear characteristics.

NOTE: Other AEROSHELL® piston engine and turbine oils, greases and fluids are also offered through our Web Platform for Supplies or can be furnished through our network of co-operating suppliers. Please refer to the supplied list of offered products or contact us for additional information or assistance on non listed products.

AVIATIONEU NEW ERA Heat...

Thermal fluids (also known with different other product titles (*) are specialized liquids used to transfer heat from one point to another in various industrial processes, including chemical processing, oil and gas refining, and power generation. Designed to operate at high temperatures they can provide efficient and reliable heat transfer, even under extreme conditions.

Heat transfer fluids can be categorized into two main types: organic and synthetic. Organic fluids are derived from petroleum, while synthetic fluids are produced from advanced chemical processes offering superior performance in certain applications. Key properties of heat transfer fluids include thermal stability, low viscosity, high flash and fire points, and low toxicity helping to ensure safe and reliable operation of heat transfer systems. Their selection depends on various factors, including the operating temperature range, heat transfer efficiency requirements, system design, and safety considerations.

Sourced from quality producers, thermal fluids are offered as part of our own labelled (AVIATIONEU NEW ERA) product lines in different grades and packaging options including 210-Liter drums and 26-Liter pails.They exhibit similar characteristics, equivalent performance and consist cost effective alternatives to respective brands of well known producers such as Eastman (Therminol®), Dow Chemical (Dowtherm™), ExxonMobil (Mobiltherm™), and others.

Based on synthetic blends, AVIATIONEU NEW ERA synthetic heat transfer fluids can be used for heating and cooling processes in a variety of industrial applications resulting in economy, efficient operations, minimum maintenance, and precise temperature control.  Indicative industries of their application include: hydrocarbon processing (oil and gas, natural gas, refining, etc.), plastics processing, chemical processing, food & beverage processing, renewable energies and many others.

Depending on the selected product, they exhibit features and benefits outlined below:

Wide temperature operating ranges

Extended service life

Exceptional thermo-oxidative stability

Fast heat transfers

Excellent compatiblity

Low volatility

Cost savings

Appearing prices are per liter.

For additional information please refer to the Product Description section or contact us.

(*)  thermal oils, thermic fluids, thermo fluids, heat transfer fluids, heat transfer oils, hot oils, thermic oils or thermo oils.

AVIATIONEU NEW ERA Aviation...

The AVIATIONEU NEW ERA aviation lubricants form part of our own labelled (AVIATIONEU NEW ERA) product portfolio  and include an extensive range of piston and turbine engine oils, greases, hydraulic, coolant and other fluids used in a variety of applications in general aviation as well as commercial (transport) and military aircraft of Russian manufacturers, such as Ilyushin Mikoyan, Irkut, Sukhoi, Tupolev and Yakovlev (now merged and operating under a new company, United Aircraft Corporation), Ukrainian (Antonov), and others.

The AVIATIONEU NEW ERA lubricants are analogues and offered as cost effective alternatives to AEROSHELL®, EXXONMOBIL®, NYCO, LUKOIL®, ANDEROL®, ROYCO®, and other lubricants used in aircraft of Eastern manufacturers. Sourced from various quality producers, the AVIATIONEU NEW ERA aviation lubricants are offered in different packaging options (*) in liters or kilograms (depending on the lubricant and the producer). OEM brands are also included in our offered product range and can be furnished through our current network of co-operating suppliers. Please refer to the supplied table(s) and presentations listing their respective products. Due to our continuously expanding list of suppliers and the respective range of offered products, certain products may not be currently listed in our Web Platform for Supplies. In this case please contact us for additional information and assistance.

An overview of offered AVIATIONEU NEW ERA AVIATION HYDRAULIC FLUIDS & PRESERVATIVES is included in the Product Description section serving as a Quick Guide. For the AVIATIONEU NEW ERA ENGINE OILS and GREASES please refer to the respective separate product presentations. The appearing lists of AVIATIONEU NEW ERA lubricants are non exhaustive due to our continuously expanding range of offered products.

(*) Depending on the lubricant and the producer, AVIATIONEU NEW ERA aviation lubricants are offered in cans, pails, flanks, drums or other containers with the following indicative capacities:

 0.9kg/1L, 3.6kg /4L, 4.5kg /5L, 9kg /10L, 15.3kg, 27kg /30L, 54kg /60L, 91kg /100L, 182kg /200L.

CASTROL® BRAYCO™ 599...

CASTROL® is a producer of oils, lubricants, fluids and greases for a wide range of applications. The company aerospace product range includes  lubricants, fluids and cleaners. Acquired by BP in 1992.

CASTROL® BRAYCO™ 599 is a specially designed synthetic base, dark amber, rust preventative concentrate.It is designed for use as an additive for storage at 10-15% by volume for turbine engines and helicopter transmissions which use MIL-PRF-23699 synthetic turbine oils. Lower concentrations, between 5 and 10 percent, may be suitable for some component storage applications, depending upon storage conditions and length of storage. 

To receive full protection when the equipment is intended to be placed in extended storage, CASTROL® BRAYCO™ 599 should be added to the oil sump immediately after an oil change, especially in locations where high humidity and salt spray are present. The corrosion inhibited oil should be capable of limited use, not exceeding 25 hours. It is recommended to add CASTROL® BRAYCO™ 599 in concentrations between 10 and 15 percent by volume. 

Meets all the requirements of, and is qualified to MIL-PRF-8188D. Complies with General Electric, Aircraft Engine Group Specification D50TF6-S1.

CASTROL® BRAYCO™ 599 has a maximum recommended shelf life of 9 years from date of manufacture. This shelf life assumes that the product is stored in its original unopened packaging in ambient temperature conditions.

Consult the engine manufacturer's maintenance manual or service bulletin to determine the specific engine model storage requirements.

Available in different packaging options, 8 ounce tins, 5 US gallon pails and 55 US gallon drum containers.

For additional information please refer to the attached documentation.

CHEMETALL® ARDROX® Alkaline...

CHEMETALL® ARDROX® 185 Series colorless scale/rust removers have a greater than 12.5 pH level and a relative density of 1.43. The series includes 185L, a highly alkaline concentrated solution in water containing sequestrants and 185 water soluble powder offering a strong alkaline solution containing sequestrants. They can be used to remove rust and scale from iron and steel  in immersion tanks but also oil, grease and some air-dried paints.  They will not attack or cause hydrogen embrittlement in ferrous alloys and there is markedly less tendency for re-rusting to occur than with acid pickling.

ARDROX® 185L is usually used at a concentration of 30-50% by volume in water, depending on the amount of rust or scale to be removed. This corresponds to a concentration of 200 - 375 g/L of ARDROX® 185 in water. ARDROX® 185 must always be dissolved in cold water. There will be an exothermic reaction and the solution will heat up to 50-60°C / 120-140°F. The ARDROX® 185L is applied by immersion between 82 and 93°C (180 and 200°F). Agitate with mechanical agitation, do not use air agitation.

The immersion time will vary according to the degree of contamination, light rust being removed in approximately 10 minutes while heavy rust may take about an hour. If the components are heavily contaminated with oil or grease, the life of the ARDROX® 185L  bath will be prolonged if they are first degreased (e.g. with an ARDROX 6-series product).

When used in conjunction with the adequate other ARDROX® specialties (sold separately), ARDROX® 185L can be used to remove scale from hot-end jet engine components. It can also be used for cleaning parts made of titanium.

Thorough water rinsing must take place after the use of ARDROX® 185L. If no further immediate surface treatment is to follow, the use of a dewatering and protective fluid such as an ARDROX® 3-series is desirable to give protection from re-rusting.

The ARDROX® 185L  comes in a 5-gallon and 180-liter containers while the 185 powder in 25 kg bags.

Qualifications / Approvals:

SAE - ARP 1755B ( conformance )

CFMI - CFM56

Rolls Royce - CSS244 OMat

SNECMA - DMR 70-620

GE SPMC 70-80-04

Pratt Whitney - SPMC 70-12-00

Turbomeca

For additional information please refer to the attached documentation.

CHEMETALL® ARDROX®...

CHEMETALL® ARDROX® brand is the leading brand for aerospace surface solutions including paint and scale removers, exterior aircraft & gas turbine engine compressor cleaners, corrosion inhibiting and non-destructive testing protective compounds for both aircraft and aero engines and materials.

CHEMETALL® ARDROX® Corrosion Inhibiting Compounds' (CIC) range includes AV 8, AV 15 (aka DINITROL AV15), general purpose AV 25, the most versatile AV 30 and AV 40.  They are water displacing, long-term corrosion inhibitors highly  penetrating  areas exposed to severe corrosion conditions and combining good penetration properties with excellent corrosion inhibiting characteristics and a low applied film weight. Their viscosity is optimised to ensure an effective protective coating and promote penetration into otherwise inaccessible areas of the airframe. Applied as a coating to protect metals in airframe structures, on painted and unpainted surfaces, and in aerospace components to safeguard metals from corrosion:

- by dipping, brushing or spraying, recommended for maximum penetration capability and most effective corrosion inhibiting performance.

- as a spray using either the specifically designed ACS - System (airmix application equipment), or the AAS - System (airless application equipment) in accordance with CHEMETALL® operating instructions.

In areas exposed to severe corrosion conditions AV 8 should be overcoated with AV 100D - a heavy duty, waxy, firm film CIC.

Movable parts should be masked before treatment unless spray application can be controlled to prevent direct contact. If spray control or masking of movable components is not possible, then AV 25, a soft waxy film CIC, should be used. The latter is designed for use on pulleys, control cables and other movable components.

CHEMETALL ARDROX® corrosion inhibitors are offered in different packaging options and comply with different specifications including Boeing BMS, MIL-PRF-16173, McDonnell Douglas DMS, Airbus AIMS and others.

CHEMETALL ARDROX® 3140 Corrosion Preventative contains film forming agents, antioxidants and corrosion inhibitors in a refined hydrocarbon solvent base. Provides long term protection for raw materials, sub-assemblies and finished components, which are to be stored or used in corrosive environments. 

For additional information on ARDROX® CIC please refer to the attached documentation.

HAZMAT Hazardous Material UN Number: UN1139 - UN Class: 3. Hazmat packaging & certification required.

CONNTECT® Gas Turbine...

CONNTECT® produces and supplies combustion turbine fuel additives, compressor cleaners & wash systems and related products. CONNTECT® gas turbine compressor cleaners include CONNTECT® 5000, 6000, 7000 and CONNTECT® AF-100 anti-icing fluid for use with all CONNTECT® compressor cleaners. They are suitable for both ON LINE and OFF LINE use while ceaners can be injected directly into the compressor while the turbine is operating ON LINE extending periodic OFF LINE cleaning intervals and reducing average power loss. Available in 5-gallon pails, 55-gallon (208-liter) drums and 330-gallon re-usable and disposable bulk containers (totes).

CONNTECT® 5000 - concentrated water based gas turbine compressor cleaner specifically designed to remove deposits commonly found on gas turbine compressor blades.

CONNTECT® 6000 - concentrated non-toxic high performance low foam water based gas turbine compressor cleaner with cleaning efficiency similar to solvent-based cleaners.

CONNTECT® 7000 - concentrated solvent-based gas turbine compressor cleaner. The combination of non-ionic surfactants, emulsifiers and organic solvents is specifically designed to remove deposits commonly found on gas turbine compressor blades including carbonaceous deposits, oil, grease and soot. It should not be used undiluted.

The ash free ingredients in CONNTECT® cleaners have been carefully selected to ensure that no incremental trace elements can contribute to corrosion of the hot section of the gas turbine, while they contain special inhibitors to ensure compatibility with aluminum, nickel, nickel-cadmium, stainless steel, titanium and common coatings including painted surfaces and elastomers. They can be generally mixed at 1 part cleaner to 4 parts water but the method of injection and total amount of cleaning solution required differs for ON LINE and OFF LINE cleaning.

CONNTECT® AF-100 is a superior quality, specially designed propylene glycol based gas turbine anti-icing fluid for use with all CONNTECT® compressor cleaners. It is non-hazardous, non-toxic and biodegradable. High purity, ash free product insuring no incremental contamination of the hot section of the turbine.  Depending upon the percentage of AF-100 used, the freezing temperature of the cleaning or rinsing solution can be reduced down to -22 deg. F (-30 deg. C). However, its viscosity increases significantly at cold temperatures should not be mixed with cleaner or water when the  product is very cold.

DONALDSON AEROSPACE...

DONALDSON COMPANY INC. is one of the largest filtration manufacturers in the world, providing filters and filtration components for a wide range of applications including commercial airliners, military applications and general aviation aircraft, agriculture and forestry, construction, mining,  truck, and bus manufacturers as well as other markets.

DONALDSON AEROSPACE FILTRATION (AFS) cleaners/degreasers and oils are used in inlet barrier filters to bring the filters back to full capacity after their cleaning process. Offered in 1 US gallon and 5 US gallon sizes. Filter Cleaning Kits are also offered containing 1 US gallon of AFS Oil, 1 gallon of AFS Cleaner/Degreaser, a 16-ounce bottle and spout for re-oiling, a cleaner/degreaser sprayer, and seamer pliers (2-inch and 6-inch).

For additional information please consult the supplied documentation.

EASTMAN SKYDROL™ Aviation...

EASTMAN SKYDROL™ Aviation Hydraulic Fluids were developed to meet the requirements established by manufacturers and backed by recognized experts in phosphate ester technology. SKYDROL™ was the first fire-resistant hydraulic fluid in the industry and today remains the most advanced aviation hydraulic fluid. SKYDROL™ aviation hydraulic fluids include:

SKYDROL™ PE-5,  a Type V, fire-resistant hydraulic fluid offering the longest fluid life of any phosphate ester fluid available today, even under high moisture conditions. Key benefits include less frequent fluid replacement, reduced disposal volume and lower environmental footprint. Meets BMS3-11P Type V, Grade A & C specification.

SKYDROL™ 5, a lighter-weight hydraulic fluid due to its lower density resulting in fuel savings.  SKYDROL™ 5 is the first aviation hydraulic fluid demonstrating erosion-resistance at higher temperatures leading to decreased maintenance and downtime. Meets BMS3-11P Type V, Grade B & C specification.

SKYDROL™ LD-4, the world’s best-selling Type IV aviation hydraulic fluid, featuring low density, valve erosion prevention, and deposit control. Erosion resistance is made possible by a breakthrough anti-erosion additive and acid scavenger included in the formulation. Meets BMS3-11P Type V, Grade B & C specification.

SKYDROL™ 500B-4, the only commercially available standard-density aviation hydraulic fluid offering additionally improved erosion resistance, as it contains the same anti-erosion additive and acid scavenger as LD-4. Meets BMS3-11P Type IV, Class 2 specification.

For additional information please refer to the supplied documentation or contact us.

EASTMAN THERMINOL® Thermal...

Therminol® family of of thermal fluids and heat transfer fluids, produced by Solutia Inc, a subsidiary of Eastman Chemical Co., are used for process heating and cooling. Eastman Therminol® high-performance synthetic heat transfer fluids have been developed specifically for the indirect transfer of process heat. Today, the Therminol® brand is that of top-selling synthetic heat transfer fluids in the world with uses  in more than 15,000 systems.

Eastman Therminol® heat transfer fluids are designed to provide precise temperature control in a variety of applications and can meet the operating needs of virtually any single- or multiple-station heat-using station heating and/or cooling system, with operating ranges from -175 degrees F to 750 degrees F (-115 degrees C to 400 degrees C).  In properly designed systems,  Therminol® fluids provide excellent thermal stability within their expected temperature ranges for extended periods without breakdown or corrosion for years of trouble-free service with minimum downtime. Therminol® product lines also includes Therminol® FF flushing fluid to clean liquid-phase heat transfer systems. 

Available in various formulations and operating ranges, Therminol® heat transfer fluids provide excellent benefits—economy, efficient operation, minimum maintenance, and precise temperature control. Packaging options: 205 litre drum, 20 litre cube.

An overview of Therminol® fluids is included in the Product Description section. Please also refer to the  temperature chart and other supplied documentation for specific product performance benefits, availability, safety data, and technical specifications.

Heat transfer fluids with similar characteristics and equivalent performance to the respective Eastman Therminol® products are also offered as part of our own labelled (AVIATIONEU NEW ERA) product lines. Please consult the separate product presentation or contact us.

HENKEL BONDERITE® Aerospace...

HENKEL BONDERITE® is the premier brand for surface technology and process solutions that create competitive advantages across the industrial manufacturing marketplace.  Trusted for reliability, sustainability & proven results, BONDERITE® processes deliver superior cost-in-use and operational efficiency through a broad portfolio of cleaner, surface treatment, coating & lubricant materials along with engineering services.

HENKEL BONDERITE® range of surface treatment products for the Aerospace industry includes TOUCH-N-PREP® coatings pens, wipes, ready-to use coatings for light metals, liquid cleaners and paint strippers. An overview of these products is included in the Product Description section. For additional information please consult the supplied documentation.

LANXESS ANDEROL® ROYCO®...

ANDEROL® ROYCO® brands  of LANXESS Corporation are global leaders in lubricants with a diverse portfolio of engine, turbine,marine oils, gear,pump and bearing oils, greases, hydraulic, compressor, aviation, finished, metal working and general industrial fluids, specialty and Mil-SPEC lubricants and base stock. ROYCO® hydraulic, coolant & other fluids are offered in different packings (1 US quart cans, carts of 24 1 US cans,5 USG pails,55 USG drums, etc.).

ROYCO® 602 Cooling Hydrogenated Polyalphaolefin Syn Hydrocarbon Fluid. Composed of a highly branched, compact and very stable synthetic hydrocarbon (polyalphaolefin,PAO). 

ROYCO® 756/756A Mineral Oil Based Hydraulic Fluid for Aircraft, Missiles and Ordnance.

ROYCO® 757 Low Viscosity Mineral Based Fluid for use as an operational fluid for missile systems, aircraft, and Unmanned Aerial Vehicles (UAV).

ROYCO® 770 Synthetic Fire Resistant Hydraulic Fluid. Super clean synthetic hydraulic fluid for use in tank and howitzer recoil mechanisms and hydraulic systems, snow removal, earth moving and heavy duty construction equipment, and industrial robotic hydraulic systems.

ROYCO® 782 Synthetic Fire Resistant "Super Clean" Hydraulic Fluid for severe duty military and industrial equipment.

ROYCO® 783 Mineral Based Preservative Hydraulic Fluid recommended for use in aircraft, missile, and ordnance systems using synthetic sealing material as well as heavy duty construction equipment, and industrial robotic hydraulic systems.

ROYCO® HF-825 Acryloid Synthetic Assembly Fluid & O-Ring Lubricant.  A concentrated solution of methacrylate polymer in synthetic diester based oil providing lubricity, and a "tacky" film.

ROYCO® LGF Landing Gear & Strut Fluid. A mineral oil based hydraulic fluid designed specifically for use in aircraft landing gear systems shock struts and other fluid dampening systems. 

ANDEROL® ROYCO® and NYCO oils, greases, fluids and specialty products are used in aircraft of Russian and Ukrainian manufacturers meeting the corresponding specifications. Most of their products are included in our offered product range and can be furnished through our current network of co-operating suppliers. Please refer to the supplied table(s) listing their respective products. Due to our continuously expanding list of suppliers and the respective range of offered products, certain products may not be currently listed in our Web Platform for Supplies. Please contact us for additional information and assistance.

LUKOIL® Lubricants SKU:...

LUKOIL® LUBRICANTS brand relates to an extensive range of lubricants serving the needs of applications in different markets worlwide, from passenger cars, commercial vehicles and small engines to aviation, marine and industrial uses. LUKOIL® LUBRICANTS portfolio includes among others motor oils, transmission, gear, compressor, turbine, gas engine, machine sideway, rolling mill, circulating, quenching oils, hydraulic and coolant fluids and greases. They are available in in different packaging options. 

A brief description of LUKOIL® lubricants  which can be furnished through our network of co-operating suppliers is included in the Product Description section. For additional information please refer to the supplied documentation or contact us.

Note: Supplied information is provided for reference only. For the selection of the suitable lubricant please observe the manufacturer's instructions.

McGEAN™ CEE-BEE™ HONEY BEE™...

McGEAN™ CEE-BEE™ HONEY BEE™ 60 is an aircraft lavatory cleaner for removing water scale and stains from stainless steel. It is a thixotropic, acidic, liquid cleaner designed to remove hard water scale from vacuum and recirculating toilet systems. Regular cleaning will assist in maintaining toilet systems in good operating condition and help control odors offensive to the travelling public. Product features and benefits include:

- effectively removes water scale and stains from stainless steel

- allows for in-place cleaning, eliminating the need to remove toilet systems from the aircraft

- can be applied directly to scale deposits for local cleaning

- thickened for better cling on vertical surfaces

- safe on stainless steel, most plastics and good quality paint

- shelf life 730 days 

Approvals

Airbus AMM Task 38-31-00

Airbus Application Code: 08AHC1

Airbus Product Code: 869900

B/E Aerospace 25-33-21 (Coffee Machines)

Boeing AMM

Also offered in two other versions, Honey Bee™ 60T and 60 TNP. The first (60T ) was developed for removal of hard water scale and accumulated waste materials from vacuum and re-circulating toilet systems in aircraft. It effectively removes hard water scale from vacuum toilet system lines, lavatory holding tanks and components in immersion tank applications. Can be applied directly to scale deposits in toilet bowls for spot removal. Safe on stainless steel, acrylic plastic and good quality paint.

The second (60 TNP) was developed for removal of hard water scale and accumulated waste materials from vacuum toilet systems in aircraft preventing waste line clogs and ensuring reliable operation of the vacuum lavatory system.

60 TNP Features & Benefits:

Effectively removes hard water scale and stains from stainless steel lavatory components, titanium waste lines and waste holding tanks

Approved for use with the Cee-Bee® Vacuum Cleaning Kit

Allows for in-place cleaning, eliminating the need to remove toilet systems

Can be applied directly to scale deposits for local cleaning

Safe on stainless steel, titanium, most plastics and good quality paint

Surfactants biodegradable

For additional information please consult the supplied documentation.

NYCO HYDRAUNYCOIL® Mineral...

NYCO HYDRAUNYCOIL® range of products includes mineral and synthetic fluids for hydraulic systems and circuits subjected to high and low temperatures, resistant to fire, extreme pressure and corrosion, and biodegradable. NYCO HYDRAUNYCOIL® fluids are shock-strut fluids. The main hydraulic fluids used in civil aviation are phosphate ester based fluids produced by Exxon-Mobil and Eastman Skydrol.

Different NYCO HYDRAUNYCOIL® hydraulic fluids are available addressing the requirements of specific sectors/applications:

FH & EL series for the Automotive & Industrial sectors,

FH 14 recoil and hydraulic system fluid

FH 19 recoil and hydraulic system fluid for Navy vessels

FH 51 hydraulic fluid used on all types of aircraft

FH 5 AW / 6 AW fluids dedicated to Boeing aircraft in operation, after overhaul and under storage. Also available for Airbus aircraft.

FH 42 synthetic shock strut fluid for new generation aircraft

FH 2 helicopter and fighter jet system fluid

Applications

Aeronautical: damping fluid for landing gears (initial assembly at the main OEMs), fluids for helicopters and combat aircraft, actuators, THS (Tail Horizontal Stabilizer), test bench, etc.

Military: mobile equipment, artillery, gun-mounts, tanks, missile hydraulics, etc.

Automotive: biodegradable hydraulics for public works, lifting and marine equipment, etc.

Industrial: dams, drill bits, etc.

For more information on NYCO HYDRAUNYCOIL® fluids please refer to the supplied documentation.

NYCO and ANDEROL® ROYCO® oils, greases, fluids and specialty products are used in aircraft of Russian and Ukrainian manufacturers meeting the corresponding specifications. Most of their products are included in our offered product range and can be furnished through our current network of co-operating suppliers. Please refer to the supplied table(s) listing their respective products. Due to our continuously expanding list of suppliers and the respective range of offered products, certain products may not be currently listed in our Web Platform for Supplies. In this case please contact us for additional information and assistance.

PHILLIPS 66® Aviation...

PHILLIPS 66® Company is among the largest refiners in the U.S and a major contract jet and avgas fuel supplier to private, commercial, and military aviation. The Phillips 66® line of aviation lubricants approved by the FAA and leading engine manufacturers includes premium single and multiviscosity piston engine oils and  highest quality hydraulic fluids compatible with other brands. They can be used in diverse climatic conditions. PHILLIPS 66® protective additive packages exceed industry specifications.

Some of PHILLIPS 66® aviation lubricants listed below are offered through our Web Platform for Supplies. Others, not currently listed, can also be furnished through our network of co-operating suppliers. For more information please refer to the Product Description section, the supplied documentation or contact us.

PHILLIPS 66® Aviation Oils

PHILLIPS 66® X/C® Aviation Oil, Ashless Dispersant, Multi-Grade Engine Oil for Aircraft Piston Engines

PHILLIPS 66® VICTORY® Aviation Oils

VICTORY® Aviation Oil 100AW, Ashless Dispersant, Single-Grade Engine Oil with Antiwear Additive for Aircraft Piston Engines (PEO)

VICTORY® Aviation Oil AW 20W-50, Ashless Dispersant, Multi-Grade Engine Oil with Antiwear Additive for Aircraft Piston Engines (PEO)

VICTORY® DIESEL Aviation Oil 10W-40, Fully Synthetic Aviation Engine Oil for Aircraft Compression Ignition Engines

PHILLIPS 66® TYPE A Aviation Oil, Ashless Dispersant, Single-Grade Engine Oil for Aircraft Piston Engines. Available in two grades, 100AD (SAE 50) and 120AD (SAE 60)

PHILLIPS 66® TYPE M Aviation Oil, Non-Dispersant, Multi-Grade Engine Oil for Aircraft Piston Engines

PHILLIPS 66® Aviation ANTI-RUST Oil, Rust & Corrosion Preventive Oil for Aircraft Piston Engines

SHELL® Industrial...

SHELL® extensive range of industrial lubricants including the company  GTL (gas-toliquids) technology oils highlight the difference between industry standards and industry-leading performance. 

SHELL® range of industrial lubricants include lubricating oils for a variety of applications, hydraulic oils, coolants and greases.

SHELL® lubricating oils can be used on turbines (TURBO turbine oils), rotary and reciprocating compressors (CORENA), stationary gas engines (MYSELLA), power-generation (ARGINA & GADINIA), transformers (DIALA), axle, gear and transmission systems (SPIRAX ), slideways (TONNA), as bearing & circulating oils (MORLINA) as well as process oils (RISELLA X). TELLUS hydraulic oils, COOLANTS and GADUS greases are also offered as part of SHELL® range of industrial lubricants. They are briefly presented in the Product Description section while further information can be obtained through the supplied documentation.

SOLIDUS ZOK 27 Gas Turbine...

ZOK 27 by SOLIDUS INDUSTRIES is a powerful water-based gas turbine compressor cleaner and corrosion inhibitor. Originally developed for the UK Ministry of Defence over 40 years ago, ZOK 27 is used all over the world today within the Aviation, Marine, Power Generation, Oil and Gas and Industrial sectors. Regular on-line and off-line washing with ZOK 27 produces outstanding results in gas turbine engine performance: reducing fuel consumption, exhaust gas temperatures and emissions, while simultaneously increasing power recovery and the overall lifespan of engine components – ultimately maximising the ROI on gas turbines.

SOLIDUS INDUSTRIES ZOK 27 Gold Standard is a neutral, biodegradable, water-based gas turbine compressor and gas path cleaner. Specially formulated with plant based surfactants, this product meets the gold standard for ecological sustainability for use in the North Sea as outlined in the OSPAR convention. ZOK GOLD is the perfect solution for maintaining peak performance of gas turbine compressors operating in ecologically sensitive environments. Regular on-line and off-line washing with ZOK 27 Gold Standard produces outstanding results: reducing fuel consumption, exhaust gas temperatures and emissions, while simultaneously increasing power recovery and the overall lifespan of engine components – all this while minimising  environmental footprint.

ZOK 27 and ZOK 27 Gold Standard  are available as CONENTRATED (CNCTR) and READY TO USE (RTU) product versions in pails of 25 US liters and as READY TO USE (RTU) in drums of 210 liters.

ZOK 27 READY TO USE (RTU) versions are intended for users who do not have access to demineralised water. CONENTRATED (CNCTR) vesrions can be diluted 1 to 4 with water before use (20% solution). Demineralised water (<11μS/cm conductivity) should be used for hot/on-line cleaning. Good quality drinking water (<500μS/cm conductivity) may be used for cold/off-line cleaning.

Please also refer to the attached documentation for additional information on these products.

ZET-CHEMIE® Lubricants &...

ZET-CHEMIE® brand relates to a broad range of lubricants, cleaners and corrosion protection products for metal processing developed, manufactured and distributed by by ZET-CHEMIE GmbH for 30 years.

ZET-CHEMIE® water-miscible cooling lubricants are based on mineral oil-containing emulsion concentrates or mineral oil-free solutions. They have been used many years successfully for processing all kinds of materials. Their cutting and grinding oils are based on mineral or syntethic base oils and can be used in both chip and non-cutting metal machining processes. 

ZET-CHEMIE® corrosion protection products provide plants and components with the best corrosion protection depending on the application requirements.

ZET-CHEMIE® metal cleaners effectively address requirements for cleanliness of components in metalworking. 

ZET-CHEMIE® range of industrial lubricants can be used in a wide range of applications. 

HLP hydraulic oils feature good demulsifying properties, high stability against ageing and wear protection. They correspond to DIN 51524 Part 2. Available in the viscosity range ISO 2 – 150. HLP-D hydraulic oil conforms to DIN 51524 Part 2 with excellent detergent and dispersion features, plus wear protection. Available in the viscosity range ISO 68 – 150. 

CLP high-performance industrial gearbox oils are suitable for all industrial applications. They correspond to DIN 51517 Part 3. Their load stage is greater than 12. Available in the viscosity range ISO 5 – 680.

CGLP sliding track lubricating oils are suitable for tracks and guide rails. Their good demulsifying properties prevent them mixing with cooling lubricants. Correspond to DIN 51502 CGLP. Available in the viscosity range ISO 32 – 460.

VDL ZET-compressor oils with low evaporation losses and high stability against ageing conform to DIN 51506 VDL. Used in reciprocating and rotary lobe compressors according to the manufacturer’s instructions. Available in the viscosity range ISO 68 – 150. 

ZET-CHEMIE®  paraffin-based machine oils can be used for lubricating spindles in tooling machines. Transparent and resistant to oxidation. Available in the viscosity range ISO 2 – 32. 

ZET-CHEMIE® product portfolio also includes multi-purpose, fluid, bearing, high temperature and silicon greases in all NLGi classes and all container sizes from cartridges through to drums.Also car oils for petrol or diesel engines and trucks with EURO IV emission limits.

For additional information please refer to the supplied documentation.