Filter By

Electronic, Electrical & Electromechanical Materials & Parts

Electronic devices, batteries, wires, cables, electric motors, lights, bulbs, circuit breakers, terminals, servo mechanisms and other products/materials.

Electronic, Electrical & Electromechanical Materials & Parts

Active filters

B&C SPECIALITY PRODUCTS...

Since its introduction in 1994, the B&C SPECIALITY PRODUCTS BC320 Starter for Continental engines has established an impressive service record as the ONLY starter design on the market that has provided reliable, long-term service for these engines. 

Suitable for installation on Continental engines (C-75, C-85, C-90, C-145-2, O-200, IO-240, O-300-A, -B, and -C, and GO-300-A, -B, and -C) it solves all the problems that other starter designs have had:  worn-out clutches, broken pinions, nagging oil leaks, and catastrophic failure modes. Featuring the durability of all-steel gears and heavy-duty ball-bearings, and the efficiency of a high-torque series-wound motor, it provides greater starting torque, while saving 4.3 to 5.2 lbs. over the old key-type and pull-cable type starters (respectively).

The B&C SPECIALITY PRODUCTS BC320 Starter is STC-PMA approved for use in certificated aircraft, and is available with or without the STC (*). Two installation kits are also available:  one for replacing a key-type starter (Installation Kit 501-1), the other for replacing a pull-cable type starter (Installation Kit 501-3). For key-type starters, before installing the BC320, you will need to remove the needle bearing pressed into the engine case & install the supplied plug in its place. For pull-cable starters, before installing the BC320, you will need to cut off the 9/16 steel shaft that is installed in your engine case.

Other versions of BC320 Starter for 12v and 24v electrical systems (BC320-2, 12v Counter-Rotating or the 24v BC320-3) are also available.

(*) For the issue of the STC, the aircraft make and model, aircraft registration and serial number are required.

CHAMPION AEROSPACE...

Slick magnetos by CHAMPION AEROSPACE are used on nearly all aircraft piston engines. They exhibit distinct design and operational features outlined below ensuring improved performance and service life.

Smaller and lighter unique design

Radio noise suppression

Lift-off housing

Easy to maintain

OEM Approved for more than 225,000 aviation engines

Service at 500-hour intervals (*)

CHAMPION AEROSPACE Slick magnetos are offered in NEW or FACTORY OVERHAULED condition (**) in a broad range of options. Both can be supplied as exchange units to returned cores and include genuine OEM parts produced and inspected under rigorous procedures to ensure airworthiness and suitability in Slick magnetos. The factory overhauled magnetos are sourced by CHAMPION AEROSPACE authorized overhauling stations and adhere to strict CHAMPION AEROSPACE restrictions on the use of parts and service literature.

For additional information please refer to the Product Description section and the supplied documentation.

(*) In accordance with CHAMPION AEROSPACE Overhaul Manual L-1363F, the magneto should be overhauled at TBO, lightning strike, prop strike, sudden stoppage of the engine and immersion of the aircraft.

(**) NEW EXCHANGE or FACTORY OVERHAULED EXCHAGE Slick magnetos are offered in exchange of an existing customer owned unit (core) for a quick turn around. A refundable core charge is included in the selling price. This is refunded or credited towards future orders with us when a qualified core is returned and its condition is approved by our co-operating supplier within 60 days of the date of the purchase invoice. As a general rule, approvals of core returns for FACTORY OVERHAULED Slick magnetos are granted to cores of the current series of these magnetos while for NEW EXCHANGE Slick Magnetos, cores of older series of Slick magnetos can be considered for credit on a case by case basis. In all cases, the approval of a returned core remains at the exclusive discretion of our co-operating supplier and shipping back to the customer of non-approved cores are subject to additional charges.

SUPERIOR PANEL TECHNOLOGY...

SUPERIOR PANEL TECHNOLOGY (SPT) has developed a brighter, more uniform and longer lasting glare shield lighting system. The 18” x 1” glow strip electroluminescent lamps provide a beautiful fluorescent-like aviation green or a white light output. The ultra-thin lamps (.065 including the adhesive backing) are very flexible and conform to the curves of the underside of the glare shield. The SPT Glow Strips meet the FAA 23.853 burn test. Inverters are included with the kit. They are offered with or without a dimmer. The recommended dimmer for the strips is the Pulse Width Modulating (PWM) dimmer by SPT. Optional 14V or 28V battery back-up systems are available and recommended. SPT offers LIFETIME warranty on the Glow Strip lamps and 5-year warranty on the PWM dimmers.

SUPERIOR PANEL TECHNOLOGY (SPT) Glow Strip Product Range:

Green

GS1-18-14G Single Glow Strip-14V

GS2-36-14G Two lamp Glow Strip-14V

GS2-36-28G Two lamp Glow Strip-28V

Green with PWM Dimmer without off switch on dimmer 

GS1-18-14GPWM Single Glow Strip-14V

GS2-36-14GPWM Two lamp Glow Strip-14V

GS2-36-28GPWM Two Lamp Glow Strip-28V

Green with PWM Dimmer with off switch on dimmer  

GS1-18-14GPWMS Single Glow Strip-14V

GS2-36-14GPWMS Two lamp Glow Strip-14V

GS2-36-28GPWMS Two Lamp Glow Strip-28V

White

GS1-18-14W Single Glow Strip-14V

GS2-36-14W Two lamp Glow Strip-14V

GS2-36-28W Two lamp Glow Strip-28V

White without off switch on dimmer

GS1-18-14WPWM Single Glow Strip-14V

GS2-36-14WPWM Two lamp Glow Strip-14V

GS2-36-28WPWM Two Lamp Glow Strip-28V

White with off switch on dimmer

GS1-18-14WPWMS Single Glow Strip-14V

GS2-36-14WPWMS Two lamp Glow Strip-14V

GS2-36-28WPWMS Two Lamp Glow Strip-28V

Battery Back-Up

BP14V Battery-Back Up 14V

BP28V Battery-Back Up 28V

Aircraft Replacement Light...

Aircraft Replacement Landing & Taxi Light Lamps sourced from different manufacturers. GE Lighting has been acquired by Tungsram. All bulbs are identical, but packaging may differ at the time of shipment.

Surface Acoustic Wave (SAW)...

Surface Acoustic Wave (SAW) devices are components that make use of the ability of piezoelectric materials to convert acoustic (i.e. mechanical) waves into electromagnetic signals, and vice-versa. By far, the most common SAW devices are those which perform a filtering operation, also known as SAW filters. SAW Band Pass Filters (SAW BPF) sort signals by frequency the most widely used substrates being quartz (SiO2), lithium niobate (LiNbO3) and Lithium tantalite (LiTaO3) that are very brittle materials.

Usually SAW filters operate from 600 MHz to 2 GHz frequency range in mobile environment. Based on IF (Intermediate Frequency) and RF (Radio Frequency) filtering, there are two types of filters, IF SAW and RF SAW filters. In addition, based on construction, there are different  types of offered SAW filters such as IIDT, DMS and ladder.

Main advantages or benefits of SAW filters include:

• they allow electro-acoustic coupling via the transducer

• SAW velocity is 105 times less than that of Electromagnetic (EM) wave. As a result, SAW filters can be used in cases where EM wave based filter designs are impractical to be developed

• SAW filters are less expensive compared to BAW (Bulk Acoustic Wave) filters

• SAW filters are easy in fabrication due to easy access to their structure from the above surface of the filter.

The selection of the right SAW filter for an intended application is based on significant parameters like those listed below. Such filters are produced by different manufacturers such as TAI-SAW, Qualcomm, API, Golledge Electronics, Oscilent, Amplitronix LLC, Vectron, Filtronetics, Microsaw, SAWTRON and others.

• RF or IF type

• RF center frequency

• Bandwidth

• Pass band ripple (dB)

• Power handling capability

• Insertion loss in pass band (dB)

• package type and dimension

Please refer to the specifications of offered SAW filters, the supplied documentation or contact us for additional information.

MIL-DTL-38999 Series I...

MIL-DTL-38999 Series I Connectors are high-performance cylindrical connectors used on  aerospace and other applications. Sourced from reliable manufacturers such as AMPHENOL, TE CONNECTIVITY, CORSAIR and others they are offered in different sizes,  shell styles, materials and finishes. Designed for rugged reliability, they provide excellent vibration, corrosion and shock resistance, and offer excellent EMI protection and shielding effectiveness. Please refer to the supplied documentation for additional information.

B&C SPECIALITY PRODUCTS...

BC207 High/Low Voltage Warning Indicator by B&C SPECIALITY PRODUCTS  is a solid-state device which provides a visual indication of abnormal bus voltage via a panel-mounted warning light (included). It is intended for use in non certified aircraft. Not FAA Approved. When flashing,the warning light indicates a bus voltage greater than 15.5 volts D.C. When steady, it indicates a bus voltage below 12.5 volts D.C. The product also includes B&C S708-2 Miniature Push-Button switch (push-to-test). The BC207  Voltage Warning Indicator can be used in both 14v and 28v electrical systems. 

ACS A-510-2 FAA-PMA...

Fine quality switch from ACS used in many aircraft. The switch housing is machined from billet aluminum which makes this switch 25% lighter. It provides “ON” and “OFF” electrical control of both magnetos on a single engine aircraft. The key-operated switch mounts from the rear of the panel in a 7/8” dia hole. Available with or without starter position. A-510-2 model with starter position is supplied with switch plate two keys. (diode included). FAA PMA Approved. Made in USA.

ACS MIL-C-27500 Aircraft...

Top quality shielded & jacketed single and multiple-conductor aircraft wires by ACS  conforming to MIL-C-27500 specification which replaces MIL-C-7078/3. They incorporate MIL-W-22759/18 basic wire and feature a Tefzel™ ETFE (ethylene-tetrafluoroethylene resin) insulation, a shield of tin- plated copper braid and a jacket of Tefzel™. They are temperature rated to 150°C & voltage rated at 600 volts. Available in different gauge(*) sizes. Color: White. Sold in feet (in 10 ft increments) or rolls/spools of specified length in feet indicated after the letters "RL"in the product reference number (SKU). These wires are accompanied by our Certificate of Conformance (CoC). If additional certification (as applicable) is required, extra charges apply.

(*) Wire gauge is a measurement of wire diameter. This determines the amount of electric current a wire can safely carry, as well as its electrical resistance and weight. 8 Gauge shielded wire is used in converting generator systems to alternators.

ATS 420DX Heavy Duty Spark...

A complete spark plug gapping solution for field or bench use by AIRCRAFT TOOL SUPPLY COMPANY (ATS). Includes the Heavy Duty Spark Plug Gapping Tool to accurately set your spark plug gaps to within 0.001". Also included is an Electrode Erosion Gauge to make sure that your gapped plugs are still in serviceable condition.You also get a set of wire feeler gauges to verify gap size. In case of an accidental over-gap of the plug, the included Gap Expansion Tool will get you back on track. Compatible with all Champion, and AutoLite Massive Electrode Spark Plugs. The complete kit includes:

1 X Gapping Tool

1 X Feeler Gauge

1 X Erosion Gauge

1 X Gap Expansion Tool

AMPHENOL AR Series ARINC...

"AR" Series connectors from AMPHENOL are multi-purpose connectors used in aerospace, military and computer periphery applications. Designed per ARINC 404 specifications AR connectors utilize pin and socket contacts manufactured in conformance with MIL-C-39029. They meet or exceed the requirements of MIL-C-81659 and ARINC Specification 404.

These connectors are available in five shell styles with up to four insert cavities. Inserts in AR product line accommodate signal and power contacts in sizes 12, 16, 20 and 22. Coaxial contacts are available in sizes 5 and 9. Insert arrangements are available utilizing a single type contact or a combination of standard and coaxial contacts.

Non-environmental and environmentally sealed connectors are offered. The environmental sealing is accomplished by wire sealing grommets and interfacial seals. Application specific designs, including transient protection, are available from Amphenol. 

For additional information please refer to the supplied documentation.

Note: Special Order items. Non-Cancellable/Non-Returnable Upon Order Placement (NCNR). Minimum Order Quantities & long lead times usually apply. Contact us. 

AMPHENOL Cable & Harness...

Different wiring accessories such as cable and harness supports are used to secure and guide wire bundles throughout an aircraft, train, UAV, mass transport vehicle or other platform. They are designed, manufactured and offered by AMPHENOL Corporation, a premier manufacturer of interconnects systems for Military, Aerospace and Industrial applications as part of product lines of AMPHENOL subsidiaries Air LB,  PCD or CONEC.

NSA935504 wiring supports (brackets) by AMPHENOL Air LB and combine strength, reliability, stability and light weight. They secure cable harnesses with the use of ties simplifing wire bundle installation & maintenance. They feature an operating temperature between -55°C and +135°C. AMPHENOL Air LB wiring supports are offered in a variety of materials, shapes,  and sizes to meet intended application requirements. 

Cable Supports by AMPHENOL PCD are offered in nylon, ultem, and PEEK and are designed for use in airframe, fuel tank, and engine applications. Available in various standard configurations and sizes, AMPHENOL PCD  also offers customized products to help meet specific customer requirements.Their features & benefits include:

Lightweight & Easy to install

Multiple types: L-Frame/P-Frame, S-Frame, and Anchor Support

FAR25-853 compliance: Can meet high temperature requirements

Multiple colors available: Helps identify different sizes

Nylon 6/6 (PA), Ultem (PEI), or PEEK available

No loose parts (reduction of FOD): Lean manufacturing; reduces costs

Harness supports by AMPHENOL PCD are designed for lean manufacturing and durability and are used to secure and guide wire bundles throughout an aircraft. Built in a one-piece, lightweight design with multiple fixing points, these high performance products are strong, durable and make wire bundle installation and maintenance easy. They are able to support large bundles and high stress requirements.

Wiring accessories are sold  in pieces or pacls (bags) with a specified number of pieces indicated after the letters "PK" in the product reference number (SKU). Equivalent products are also offered y other manufacturers. For more information please refer to the supplied documentation.

AMPHENOL BNC Series RF...

AMPHENOL Bayonet Neill Concelman (BNC) product series connectors are miniature quick connect RF connectors. They feature two bayonet lugs on the female connector. BNCs are ideally suited for termination on miniature and subminiature coaxial cable (RG-58, 59, to RG-179, RG-316, etc.). Other BNC series include:

HD-BNC product series featuring the trusted, push and turn interface of a traditional BNC and providing tactile feedback and a positive lock for quick and guaranteed mating and 

Mini-BNC product series allowing higher connector densities while preserving the positive characteristics of the full-size 75 Ω BNC. The Mini-BNC provides the same positive locking bayonet system found on the BNC but allows 40% more interconnects in the same area.

ATTWOOD S3 Series Automatic...

ATTWOOD S3 Series Automatic Bilge Switch incorporates a proprietary Electronic Sensing technology to detect bilge water levels and trigger pump activation and has been engineered to operate in any bilge water mixture consistently without failure. Your pump won’t be exposed to continuous cycling as the S3 switch can easily distinguish splashing bilge water, chemicals, sludge build up or foam and comes equipped with fully sealed electronics that are completely protected from water or chemical damage. For added convenience, the bilge switch can be mounted on the floor of the bilge directly to a stringer wall or alongside the basket of the pump without added components or brackets. The S3 Series switches are also directly compatible with all competitive products and free of moving parts that can jam up, break or wear out over time.

They carry a 5-year warranty.

The S3 Series Automatic Bilge Switches are offered in different Amp and Voltage ratings and also as clamshell.

AVEO PowerBurst NG™ DayLite...

At only 26 millimeters in height (1.024 inch) the new PowerBurst NG™ DayLite by AVEO ENGINEERING is a Nav/Position/Strobe light that does not sacrifice anything in performance or standards as other economy-priced lights offered by the competition.The exclusive and highly advanced optics and chrome reflector system, unmatched power and LED management circuitry, and AVEO 's famous lowest-drag profile in the industry are all combined into a product that gives you unmatched power and features. Lower, narrower and shorter PLUS much lighter than industry lights in this category. This is not a TSO certified light. Intended for experimental aircraft.

Product Features:

3-in-1 Nav/Position/Strobe

Extremely lightweight

Unmatched circuit technology

Waterproof

Vibration-proof

Shock-proof

Dust-proof

Limited 3yr Warranty - Product must be registered within 30 days of purchase Here

Product Specifications:

Dimensions (mm): 115 mm x 33 mm x 26 mm

Dimensions (inches): 4.547” x 1.302” x 1.024”

Weight: 70 g / 2.47 oz

Operating Voltage Range: 9 – 18 V DC

Input Current – Position / Nav - green (@14V): 0.28 A

Input Current – Position / Nav - red (@14V): 0.23 A

Input Current – Strobe (@14V): 2 A peak

Output Power - Position / Nav - green: 3.3 W

Output Power - Position / Nav - red: 2.5 W

Output Power - Strobe: 24 W peak

AVIATIONEU NEW ERA Silicone...

The AVIATIONEU NEW ERA silicone insulated waterproof cables are available in different numbers of solid or stranded tinned copper conductors and AWG sizes (*) with silicon insulation jacket. Suitable for AC rated voltage 450/750V and all kinds of high temperature environment such as mobile motor, steel, aviation, power plant, petrochemical, etc. They feature a strong resistance to acids & alkali, oils, moisture and they are easy to peel and cut. They pass pass the UL VW - 1 and CSA FT1 flammability tests. Nominal Temperature : 200℃. Nominal voltage : 300/500V. Sold in rolls of 100 meters each, in increments of one roll and with a Minimum Order Quantity (MOQ) 3 rolls. Appearing price is for reference only. Contact us for a quotation.

(*) Wire gauge is a measurement of wire diameter. This determines the amount of electric current a wire can safely carry, as well as its electrical resistance and weight.

AVIATIONEU NEW ERA RNB DIN...

AVIATIONEU NEW ERA RNB brazed seam lug type battery terminals are made from brass and are tin plated. They can be used for control cabinets & similar applications. The seam in the barrel of the terminal is brazed allowing the terminal to be crimped in any position around the barrel, which helps give extra wire holding strength. They comply with DIN 46234 standard for solderless terminals. Solderless terminals are used in crimping with several, fine and super-fine stranded conductors. However, solderless terminals according to DIN 46234 are not suitable for single-stranded solid conductors.RNB terminals can be used with different wire sizes (American Wire Gauge  AWG) 22-2 and stud sizes. Please refer to the specifications table.  IMAX: 19A/27A/37A/48A/62A/88A/115A/160A. Sold in packs of 100 pieces each with Minimum Order Quantity (MOQ) 20 packs. The appearing price is for reference only. Please contact us for quotation.

AVIATIONEU NEW ERA SC Screw...

When battery terminals with heavy current capacity and high conductivity are required AVIATIONEU NEW ERA SC HEAVY DUTY lug type battery terminals are recommended. Similar to the AVIATIONEU NEW ERA SC brass battery terminals except that they are are produced from pure copper  and tin plated, they are available in three versions: SC(JGA), SC(JGY) and SC(JGB). Please refer to the specifications table. They can be used with wire sizes 1.5-1000mm2 (16AWG - 777MCM). Sold in packs of 20 pieces each with Minimum Order Quantity (MOQ) 5 packs. The appearing price is for reference only. Please contact us for quotation.

AVIATIONEU NEW ERA SC Screw...

AVIATIONEU NEW ERA SC screw lug type battery terminals are available in three versions: SC(JGA), SC(JGY) and SC(JGB). Please refer to the specifications table. They are made from brass (99.7% copper), tin plated and can be used with wire sizes 1.5-1000mm2 in a wide range of applications. Operating Temperature: :-55 to 150 deg. C. Sold in packs of 100 pieces each with Minimum Order Quantity (MOQ) 25 packs. The appearing price is for reference only. Please contact us for quotation.

AVIATIONEU NEW ERA RV...

AVIATIONEU NEW ERA RV ring tongue round crimp type battery terminals are made from tin plated brass (99.7% copper) with vinyl (PVC) insulation. They are available in red, blue, black and yellow colors and can be used in car industry as well as other applications. They can be used with different wire sizes (American Wire Gauge  AWG) 22-16,16-14 and 12-10 and stud sizes. Please refer to the specifications table.  IMAX: 19A/27A/37A/48A. VMAX: 600 volts. Maximum Temperature: 75 deg. C. Sold in packs of 100 pieces each with Minimum Order Quantity (MOQ) 20 packs. The appearing price is for reference only. Please contact us for quotation.

AVIATIONEU NEW ERA TR...

When there is a need for connection of a set of electrical wires, terminal blocks provide a safe & convenient way to keep them organized. AVIATIONEU NEW ERA TR series of snap on (clip type) terminal blocks allows for terminal block assemblies to be installed and realeased fast and easily. Terminal block connectors are rugged, easy to use and designed to keep wires of varying gauges securely connected. They can be mounted on the 35/7.5mm DIN rail of 1 or 2 meter length made from aluminum or zinc plated steel which is in turn can be mounted on control panel backplates. Any pole assembly is possible. With the use of a DIN rail protective conductor terminal block, the rail itself can be used as the grounding terminal block.

The connectors are offered in black color (or other colors as per customer requirements), with a rated voltage of  600V and different rated current options (10A,20A,30A or 40A). They are sold in packs of 100 pieces each and come with paper marker strips & transparent cover. DIN mount rail & accessories are available at additional cost. These can be ordered only together with the terminal blocks. Appearing prices are for reference only. Contact us for a quotation.

AVIATIONEU NEW ERA MIL...

Connectors are used on electrical wiring harnesses and are essentially enclosures (i.e., shells) which house contacts with wires. The electrical connection into the system at the contact termination is either a soldered or crimped connection (the latter removable from the connector with the use of a special tool). The shell and insert may be moisture resistant or a hermetic seal. The inserts in each connector must be oriented for correct mating, and the shell or insert usually contains a keying feature to prevent miss-mating that could damage the connector or result in an electrical problem. 

Connectors can be of a Plug (“male”) or Receptacle (“female”) type. Receptables are also termed as sockets or jacks. Plugs have prolonged connecting pins which fit into the mating sockets. Receptables have mounting features such as a flange with holes. Connectors used in aircraft are mostly those complying with Military Standards (MIL-STD) and Military Specifications (MIL-SPEC).

Different connectors, structured in series, are offered as part of our own branded (AVIATIONEU NEW ERA) product lines to provide cost-effective solutions for a variety of applications. Sourced by quality suppliers, they are available in plug or receptable types. 

AVIATIONEU NEW ERA MIL Standard MS5015 series connectors meet MIL-C-5015 specification. They ensure high electrical capability and durability at an acceptable cost and can be used for a range of applications including military ground support equipment, aircraft installations and others. Available in different case sizes (10SL,14S,16S,18,20,22,24,28 and 32) and  sold by the piece (pc.).

Product Specifications:

Shock: 490 m/s2

Relative humility: 95+-4% at 40℃ 

Insulation resistance: 5.000 Mega ohms minimum (at 25°C) 

Frequency Range: 10-2000Hz/147m/s2

Voltage Rating: 500VAC 700VDC 

Mating Type: threaded coupling

Termination : Solder

Durability (mating) ≧ 500 cycles 

Temprature Range:  -55°C ~ +125°C

AVIATIONEU NEW ERA Round...

Copper wires are conductors of electricity and they are used for a wide range of applications including power generation, power transmission, power distribution, telecommunications, electronics circuitry and others. Apart from the high conductivity copper features durability, tensile strength and corrosion resistance.

AVIATIONEU NEW ERA copper round wire product range includes bare copper, copper, paper insulated copper wires as well as double cotton covered and silver or tinned plated copper wires. 

They are offered in rolls in different wire gauges (*). Sold in kilograms except the double cotton covered wire which is sold by the meter. Appearing prices is for reference only per UOM. Please contact us for a quotation.

Bare Copper Wire, Gauge 0-5

Paper Insulated Stranded Wire, Gauge 0-5

Tinned Plated Copper Wire (Temperature 120 deg. C), Gauge 0.2-2

Silver Plated Copper Wire (Voltage up to 1000 V, Flame Retardant), Gauge 0-5

Double Cotton Covered Copper Wire, Gauge 0-5

(*) Wire gauge is a measurement of wire diameter. This determines the amount of electric current a wire can safely carry, as well as its electrical resistance and weight. Please refer to the respective table.

AVIATIONEU NEW ERA...

Thermocouple and thermocouple extension wires are flexible, insulated wires the first used to link a thermocouple to a temperature control device or make the sensing point (or probe) of the thermocouple while the second to extend a thermocouple signal from a probe back to the measuring instrument reading the signal over long distances.

There are different types of thermocouples conctructed from 2 conductor solid core thermocouple grade specified gauge insulated wires with a positive and negative lead and an insulated outer jacket. Types N, K, E, J, T are base metal thermocouple wires  mostly used while Types S, R and B are precious metal thermocouple wires. Common Thermocouple Wire Types are outlined below while their more detailed presentation and characteristics are included in the Product Description section.

K-Type thermocouple (nickel-chromium (nickel-silicon - nickel-aluminum). Base metal thermocouple with strong oxidation resistance with a temperature measurement capability from 0 to 1300 °C.  Main disadvantages include among others a high-temperature stability of thermoelectric potential lower than of N-type and precious metal thermocouples and a poor short-term thermal cycle stability in the range of 250-500 °C.

T-Type thermocouple (copper-copper-nickel). It has the highest accuracy and good uniformity among the base metal thermocouples and an operating temperature between -200 and 350 ℃.

J-Type thermocouple (iron-constantan ). Suitable for reducing or inert atmosphere for vacuum oxidation, and the temperature range from -200 to 800 °C.

N-Type thermocouple (NiCrSi-NiSi). Features of the thermocouple are strong anti-oxidation ability in temperature regulation below 1300 °C, good long-term stability and short-term thermal cycle repeatability, good nuclear radiation resistance, and low-temperature resistance. 

E-Type thermocouple (nickel-chromium-copper-nickel [constantan] thermocouple). Its thermoelectric potential is the highest among the commonly used thermocouples. Often selected for applications in conditions of high sensitivity, low thermal conductivity, and large resistance that can be tolerated. Less sensitive than Type K to corrosion in atmospheres containing higher humidity.

Thermocouple wires of diferent types and wire sizes (Gauges) are offered as part of own labelled (AVIATIONEU NEW ERA) product lines. Priced and sold by the foot and offered in specified or cut to order lengths (usually in 10 ft increments).

AVIATIONEU NEW ERA M27500...

Sourced from quality producers, the MIL-DTL-27500 shielded electical cables are offered as part of our own label (AVIATIONEU NEW ERA) product lines consisting cost-effective alternatives to the respective OEM products. Depending on the producer and specification, MS27500 cables come with stranded copper single or mltiple conductors (cores), nickel, silver or tin-plated and individually insulated, different number of strands, different chemically inert fluoropolymer insulation materials with good ozone and oxidation resistance as well as single or double shields. Their jackets are made of fluoropolymer, PTFE, glass, or polyamide tape.

The MIL-DTL-27500 shielded cables are used in a range of applications including avionics, military and civilian aerospace and airframe applications and ground support equipment and they are rated to a maximum voltage of 600 volts and maximum usable temperatures from 150 °C to 260 °C. 

The AVIATIONEU NEW ERA MIL-DTL-27500 cables are offered in different configurations with single or multiple individually insulated conductors (cores) in various AWG sizes, insulation materials and shields to meet application requirements. Those commonly used include components listed below but other configurations can be available. For additional information on M27500 cables, please see our brief presenation in the Product Description section.

- Stranded tin-plated cooper single or multiple-conductor(s) (aka cores) comforming with MIL-W-22759/18 specification,

- Tefzel™(**) ETFE (ethylene-tetrafluoroethylene resin) insulation on each conductor

- tin- plated copper braided shield

- Tefzel™(**) ETFE jacket

The AVIATIONEU NEW ERA MIL-DTL-27500 cables are available in cut-to-order or pre-determined lengths in feet indicated in the product reference number (SKU) and packaged in rolls or spools. They are accompanied by our Certificate of Conformance (CoC). Due to their large variety of these cables, listed products shall continuously increase. If wanted cables cannot by found, please contact us.

(*) American Wire Gauge (AWG): Wire gauge is a measurement of wire diameter. This determines the amount of electric current a wire can safely carry, as well as its electrical resistance and weight.

(**) Tefzel™ and Teflon™ are registered trademarks of the DuPont Corporation.

AVIATIONEU NEW ERA SAE...

MIL-spec were initially developed to standardize wires and cables used in military equipment. For many years, wires used in aircraft met MIL-W-5086  mil-spec and SAE-AS50861 standards superseeding them. They were manufactured with the use of tin-coated copper conductors rated at 600 volts and temperatures of 105°C and various insulating coatings including polyvinyl chloride (PVC). The PVC insulation provided resistance to abrasion, among many other things. Still in production, MIL-W-5086  cables in their various types of conductors and jacket constructions are used, apart from the aircraft in other applications that require resistance to abrasion, cut-through, impact, chemicals, and fuels. They are gradually replaced by those made in accordance with Mil-W-22759 standard due to toxic fumes generated by PVC insulation in the event of a fire. The Mil-W-22759 standard transitioned to SAE AS22759 in 2004. These two standards are essentially identical and cover a of wide range of single conductor wires (please refer to the Product Description section and supplied documentation for assistance).

Sourced from quality producers, AS22759/M22759 wires are offered as part of our own labelled (AVIATIONEU NEW ERA) product lines in different configurations, various AWG(*) sizes, in white (standard) or other color variations (desired color should be specified at the time of ordering). They are suitable for use in a range of applications in military and civilian aircraft, in harsh aircraft engine environments, for control surfaces as well as applications in areas subject to severe weather and moisture-prone (SWAMP).

Those commonly used are SAE AS22759/16  unshielded wires (replacing wires produced as per M22759/16 /17/18 and /19  specifications) but other configurations can be available. This specification uses stranded tin plated copper or silver plated high strength alloy conductors and extruded ethylene/tetrafluorbethylene (ETFE) insulation. Respective wire ratings are 150° C and 600 Volts.

The AVIATIONEU NEW ERA AS22759/M22759 wires are sold in cut-to-order lengths in 10 ft increments or pre-determined lengths in feet, indicated in the product reference number (SKU), and packed in rolls or spools. These wires are accompanied by our Certificate of Conformance (CoC). 

(*) American Wire Gauge (AWG): Wire gauge is a measurement of wire diameter. This determines the amount of electric current a wire can safely carry, as well as its electrical resistance and weight.

BRP-ROTAX® Aircraft Engine...

ROTAX® aircraft engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Ignition systems and parts are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from BRP-ROTAX® but also from other manufacturers.  Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

BRP-ROTAX® Aircraft Engine...

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different starter relay assemblies are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" after the part number in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

BRP-ROTAX® Aircraft Engine...

ROTAX® aircraft  engines form part of the product portfolio  of BRP-Powertrain GmbH & Co. KG which develops and manufactures engines for snowmobiles, watercrafts, boats, roadsters, all-terrain and side-by-side vehicles, motorcycles, carts, and aircrafts.

BRP-ROTAX® product range includes certified and non certified internal combustion engines, parts and accessories for light and ultralight aircraft.

Different spark plugs and plug connector are used in BRP-ROTAX® aircraft engines. They are offered as certified or non certified parts from the manufacturer. Non certified parts can be used in ultralights or other aircraft not requiring certification of parts for their installation. Certified parts are designated by the letters "CERT" in the product reference number (SKU).

Aircraft engine  parts are subject to changes from time to time. Some parts may be no longer available or replaced by others with different part numbers. Listed BRP-ROTAX® engine parts do not imply their current availability or suitability for your engine application. Always consult the most recent Illustrated Part Catalogs (IPCs) or other documentation available from the manufacturer for the correct part number before ordering.

CONCORDE RG Series Aircraft...

CONCORDE® BATTERY CORPORATION is a manufacturer of premium quality lead-acid batteries. The present product lines include valve regulated sealed lead-acid batteries (VRSLA) for aircraft, marine, medical, telecommunications, emergency backup, and photovoltaic applications. The CONCORDE RG Series are low resistance, valve regulated lead acid (VRLA) batteries. RG® Series batteries ship Hazmat Exempt.

The RG-25XC General Aviation  AGM 12 V aircraft battery belongs to CONCORDE Platinum Series Aircraft Batteries comprised of premium hand made AGM Aircraft Batteries with excess power for many applications. RG-25XC has the highest cranking power and capacity in the 25 Group.

TCM/BENDIX FAA-PMA Approved...

FAA-PMA Approved original equipment TCM Bendix magneto ignition switches  with 3 positions (Right/Left/Both Mags). They come complete with two keys and faceplate. For dual ignition aircraft systems, ignition switch grounds both magneto P-leads in off position.

DIALIGHT 801 Series MS25041...

Miniature press-to-test indicators with built-in bulb testing device with adjustable dimmer. The 801-series indicators feature a T-1 3/4 midget flange for 15/32" mounting hole with solder termination, black anodized mounting bushing, aluminum mounting and flange nuts hardware. The push-to-test marking is die-stamped and filled on all lens cap assemblies used with 3 terminal units.

Available in different colors (clear, green, blue, red and amber). These indicators use GE-330 (12V) or GE-327 (24V) bulbs. Bulbs are NOT INCLUDED. They can be ordered separately.

ELECTRONICS INTERNATIONAL...

The AL-1 series of Annunciator lights from ELECTRONICS INTERNATIONAL are more attractive, operate on less power and are smaller than the old fashioned indicator lights. These lights are an excellent indicator light for displaying boost pump on, gear status, power on, flags, etc. Also, they can be used as remote warning lights for any E.I. instrument featuring an external warning line. They are available in different light colors, operate on a 12 or 24-volt system and have a service life of over 1000 times that of incandescent bulbs. Mount hole: 5/16" . Size: .4" diameter x 1" depth. The come with 32" leads and E.I. documentation and certifications.

EMAS MA Series Toggle...

EMAS MA Series toggle switches feature maximum product reliability with V0 material and are offered in different contact and badge options. 

NOTE: This product is no longer available. Limited quantities may be offered from existing stocks of different vendors.

FINDER 66 Series Power...

FINDER 66 Series 30 A Power relays are electromagnetic devices available in DPDT (66.22/66.82) and DPST-NO versions (66.22-x300/66.82-x300) & different variants.

Product Features:

• Reinforced insulation between coil and contacts according to EN 60335-1

• 8 mm creepage and clearance distances

• AC coils & DC coils

• Cadmium Free option available

• ATEX compliant (EX nC) options available

Double Pole Double Throw (DPDT) Changeover (66.22 and 66.82). Commonly used to separate two circuits electrically and connect them magnetically. They are often used to interface an electronic circuit, which works at a low voltage to an electrical circuit which works at a high voltage. 

66.22 type with 30 A rated contacts, PCB mount and bifurcated terminals

66.82 type with 30 A rated contacts, Flange mount and Faston 250 connections 

Double Pole Single Throw Normally Open (DPST-NO) (66.22-x300 and 66.82-x300). Equivalent of 2 SPST switches (NO Normally Open and NC Normaly Closed) and can be used to switch 2 different loads.

66.22-x300 type with 30 A rated contacts, PCB mount and bifurcated terminals

66.82-x300  type with 30 A rated contacts, Flange mount and Faston 250 connections 

GILL LT 7000 Series Sealed...

Gill has become the OEM "original equipment battery" for Raytheon, Cessna, LearJet, Mooney, Piper, Ayres, Airtractor, Maule, Scheizer and other commercial, private and military aircraft  in the aviation industry and continues to be the industry's choice for quality battery products. In addition to the traditional Dry Battery line, Gill offers the LT Battery Sealed products featuring improved shelf life, lower weight, dependability, durability, high reliability, improved energy density, robust construction, testing and approval to DO-160E as well as FAA/PMA approval.

LT Series Batteries are fully recyclable and ship Hazmat exempt (Non Dangerous Goods).

GILL Dry Charge (Flooded)...

Gill has become the OEM "original equipment battery" for Raytheon, Cessna, LearJet, Mooney, Piper, Ayres, Airtractor, Maule, Scheizer and other commercial, private and military aircraft  in the aviation industry and continues to be the industry's choice for quality battery products. In addition to the traditional Dry Battery line, Gill offers the LT Battery Sealed products featuring improved shelf life, lower weight, dependability, durability, high reliability, improved energy density, robust construction, testing and approval to DO-160E as well as FAA/PMA approval.

LT Series Batteries are fully recyclable and ship Hazmat exempt (Non Dangerous Goods).

HARBOUR INDUSTRIES...

Harbour Industries is a QPL approved manufacturer of high temperature, high performance PTFE dielectric coaxial cables supplied in accordance with the MIL-DTL-17 specification. They are high temperature, high performance constructions exhibiting high dielectric strength and low capacitance in proportion to the cable’s dielectric constant with tolerances tighter than the MIL-DTL-17 specification to ensure uniformity of electrical characteristics, especially impedance, attenuation, and VSWR. They are priced and sold by the foot and are offered as cut to order in 10 ft increments.

Product Specifications:

Please refer to the attached table.

HARTZELL ENGINE...

SKY-TEC, a HARTZELL ENGINE TECHNOLOGIES brand, includes starters and support for Prestolite, Electrosystems, Lamar and Kelly designs. SKY-TEC OEM contactors are today installed in many general aviation aircraft while SKY-TEC FAA-PMA contractors can be used for starter, battery master/auxiliary or auxiliary power applications in replacement of OEM parts.

SKY-TEC STS-S Series FAA-PMA certified aircraft starter solenoids (aka relays) are intermittent duty suitable for starter applications. They are available in 12V (STS-S12) or 24V (STS-S24) versions. Activation: +V to S-Terminal (Frame is grounded by mounting).

SKY-TEC STS-M Series FAA-PMA approved Battery/Master solenoids are continuous duty solenoids intended for use in battery master/auxiliary applications in certified aircraft. They are available in 12V (STS-M12) or 24V (STS-M24) versions. Activation: -(Ground) to S-Terminal. (Floating ground frame).

SKY-TEC STS-A Series FAA-PMA approved solenoids are continuous duty and typically used for connecting auxiliary (ground) power. They are available in 12V (STS-A12) or 24V (STS-A24) versions. Activation: varies.

Product Features:

FAA-PMA Certified

All-metal case construction

Silver contacts (vs. copper) for high-current capability and long-life. They provide 300A in-rush capability. Much higher than the original units.

Strong spring and high-current coil for quick contact opening - minimizing arcing

Single coil terminal (other end connected to case)

High quality manufacturing 

Upgraded to perform best with today's lightweight, high torque starters

Same OE terminal layout simple to install

For additional information on different SKY-TEC series of slenoids and their applications in different aircraft please refer to the respective product presentations.

HARTZELL ENGINE...

SKY-TEC, a HARTZELL ENGINE TECHNOLOGIES brand, includes starters and support for Prestolite, Electrosystems, Lamar and Kelly designs. SKY-TEC OEM contactors are today installed in many general aviation aircraft while SKY-TEC FAA-PMA contractors can be used for starter, battery master/auxiliary or auxiliary power applications in replacement of OEM parts.

SKY-TEC STS-S Series FAA-PMA certified aircraft starter solenoids (aka relays) are intermittent duty suitable for starter applications. They are available in 12V (STS-S12) or 24V (STS-S24) versions. Activation: +V to S-Terminal (Frame is grounded by mounting).

SKY-TEC STS-M Series FAA-PMA approved Battery/Master solenoids are continuous duty solenoids intended for use in battery master/auxiliary applications in certified aircraft. They are available in 12V (STS-M12) or 24V (STS-M24) versions. Activation: -(Ground) to S-Terminal. (Floating ground frame).

SKY-TEC STS-A Series FAA-PMA approved solenoids are continuous duty and typically used for connecting auxiliary (ground) power. They are available in 12V (STS-A12) or 24V (STS-A24) versions. Activation: varies.

Product Features:

FAA-PMA Certified

All-metal case construction

Silver contacts (vs. copper) for high-current capability and long-life. They provide 300A in-rush capability. Much higher than the original units.

Strong spring and high-current coil for quick contact opening - minimizing arcing

Single coil terminal (other end connected to case)

High quality manufacturing 

Upgraded to perform best with today's lightweight, high torque starters

Same OE terminal layout simple to install

For additional information on different SKY-TEC series of slenoids and their applications in different aircraft please refer to the respective product presentations.

HARTZELL ENGINE...

SKY-TEC, a HARTZELL ENGINE TECHNOLOGIES brand, includes starters and support for Prestolite, Electrosystems, Lamar and Kelly designs. SKY-TEC OEM contactors are today installed in many general aviation aircraft while SKY-TEC FAA-PMA contractors can be used for starter, battery master/auxiliary or auxiliary power applications in replacement of OEM parts.

SKY-TEC STS-S Series FAA-PMA certified aircraft starter solenoids (aka relays) are intermittent duty suitable for starter applications. They are available in 12V (STS-S12) or 24V (STS-S24) versions. Activation: +V to S-Terminal (Frame is grounded by mounting).

SKY-TEC STS-M Series FAA-PMA approved Battery/Master solenoids are continuous duty solenoids intended for use in battery master/auxiliary applications in certified aircraft. They are available in 12V (STS-M12) or 24V (STS-M24) versions. Activation: -(Ground) to S-Terminal. (Floating ground frame).

SKY-TEC STS-A Series FAA-PMA approved solenoids are continuous duty and typically used for connecting auxiliary (ground) power. They are available in 12V (STS-A12) or 24V (STS-A24) versions. Activation: varies.

Product Features:

FAA-PMA Certified

All-metal case construction

Silver contacts (vs. copper) for high-current capability and long-life. They provide 300A in-rush capability. Much higher than the original units.

Strong spring and high-current coil for quick contact opening - minimizing arcing

Single coil terminal (other end connected to case)

High quality manufacturing 

Upgraded to perform best with today's lightweight, high torque starters

Same OE terminal layout simple to install

For additional information on different SKY-TEC series of slenoids and their applications in different aircraft please refer to the respective product presentations.

HONEYWELL MICRO SWITCH...

Honeywell is a leading switch and sensor provider for many HVAC applications, including airflow, VAV control, boiler/chillers, motors, and more.  Products include pressure sensors, digital humidity/temperature sensors, magnetic position sensor ICs, current sensors, pressure switches, basic switches, and more.

Honeywell's MICRO SWITCH switches fill many roles in a wide range of applications, including presence/absence/positioning, inspection/recognition, condition measurement, and operator/machine interface. They range from sealed switches used in high temperature aerospace applications to large cable-pull switches ensuring safety on conveyors.

Honeywell's snap-action basic switches are simple, superior, durable, and irreplaceable. Globally compliant and known worldwide for their compact and lightweight design, MICRO SWITCH snap-action switches are designed for accurate repeatability and extended life. MICRO SWITCH Basic switches are designed for presence and absence detection where physical contact with an object is permissible. They also excel in applications requiring simple on-and-off actions. 

Honeywell's  Standard families of Basic and Miniature switches include V15 series, and are designed with the same high quality standards, but for low cost-of-failure applications — ones where the cost of replacing the switch is less than the total cost of a switch failing.

The Premium families of MICRO SWITCH Large and Subminiature switches are designed for high-precision applications where the cost of a switch failing is high maintaining enhanced accuracy and repeatability. MICRO SWITCH premium basic switches are offered in different series, they feature precise and accurate characteristics. Available in large, miniature, and subminiature switch sizes, MICRO SWITCH premium basics are customizable to provide unique actuators, different terminal combinations, custom characteristics, and even value-added wires… to meet customers’ application requirements. With many Honeywell premium basics, they are tested and certified to a higher cycle count.

INTERCONNECT SOLUTIONS...

INTERCONNECT SOLUTIONS COMPANY (ISC) is a manufacturer of cables, cable assemblies, harnesses, and control panels which are used in a wide range of applications in Commercial and Military Aircraft, Lifesaving Medical Devices, Weapon Systems, Inflight Entertainment and Power Systems. The company is a supplier of Boeing and Airbus for their commercial aircraft. 

KNITTER-SWITCH Professional...

KNITTER-SWITCH & CO.KG (KNITTER-SWITCH) manufactures  a wide range of professional switches including toggle,  pushbutton, tact, slide, dual-in-line, rotary coded, rotary, encoders and snap action switches.

KNITTER switches are available in different versions (configurations), Standard with silver or silver-plated contacts and terminals, Configuration B with gold-plated (over Nickel) contacts and terminals and Configuration G with gold-plated (over silver) contacts and terminals. All switches are sealed on the terminal side and meet CE regulations. Switches for SMT as well as most series for PCB mounting are generally fully washable.

Some KNITTER switches are ESD-resistant and have an approved IP 67 waterproof rating.

KNITTER range of toggle switches includes miniature, subminiature and microminiature toggle switches offered in different series and types. Depending on the selected series and type there are offered in one or multiple poles and switching functions.

 For additional information please consult the supplied documentation.

LAMAR ELECTRODELTA X61...

Aviation grade ELECTRODELTA X61 series solenoids by LAMAR TECHNOLOGIES LLC are offered in continuous  or intermitant duty in 12 or 24 Volt. They fit current GA production aircraft as well as legacy aircraft and replace both single terminal switched units, as well as the current double terminal switched units in production today. All units have multiple quality and functional tests prior to certification and delivery. Non FAA-PMA Approved.

Product Features:

Replace most contactors in general aviation

Available in 12 or 24 Volt

Available for Continuous or Intermittent duty

All units inspected and tested to performance standards

Warranty 24 months